• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.117-124
• /
• 2004

The mixing enhancement is one of the most important problems for the development of scramjet engines. The influence of the streamwise vortices produced by a ramp in a unheated supersonic flow on the mixing of twin jets injected from its base was experimentally investigated. Nominal Mach number of the main airstream and of the twin jets at the nozzle exits were 2.35 and 2.0, respectively. Three dimensional velocity distributions near the ramp with and without injection were measured by Particle Image Velocimetry (PIV). A pair of counter rotating streamwise vortices could be seen behind the injector without injection. On the other hand, two pairs of streamwise vortices could be seen with injection. The outer one had the same direction as the vortex pair produced by the ramp, but they were stronger than those produced by the ramp. The inner ones had the opposite directions to the outer ones. It is considered that these vortices enhance the mixing near the injector.

• 대한토목학회논문집
• /
• 제26권3B호
• /
• pp.253-262
• /
• 2006

본 연구에서는 복단면 개수로 난류흐름에 대한 직접수치모의(DNS)를 수행하였다. DNS 자료를 이용하여 평균흐름 및 난류 구조를 제시하며, 기존의 실험자료 및 수치해석결과와 비교된다. 주수로와 홍수터의 접합부 부근에서 쌍와(雙渦)가 생성되는데, 그 최대크기는 체적평균된 주흐름방향 유속의 약 5%로 나타났다. 쌍와(雙渦)의 영향에 의해 접합부에서 벽전단응력이 최대값을 보였는데, 이는 기존 LES 자료와는 일치하지만 기존 실험연구결과와는 다른 것으로 그 원인에 대해 상세히 논의되었다. 사분면 해석을 통해 접합부 부근에서 레이놀즈 전단응력은 주로 쓸기현상 및 분출현상에 의해 생성되는 것으로 나타났다. 또한 조건부사분면 해석을 통해 지배적인 고유구조의 방향성이 레이놀즈 전단응력 및 쌍와(雙渦)의 생성을 결정한다는 것을 확인하였다.

• Wind and Structures
• /
• 제26권5호
• /
• pp.305-315
• /
• 2018

A numerical study based on a delayed detached eddy simulation (DDES) is conducted to investigate the aerodynamic mechanism behind the suppression of vortex-induced vibrations (VIVs) of twin box girders by central grids, which have an inhibition effect on VIVs, as evidenced by the results of section model wind tunnel tests. The mean aerodynamic force coefficients with different attack angles are compared with experimental results to validate the numerical method. Next, the flow structures around the deck and the aerodynamic forces on the deck are analyzed to enhance the understanding of the occurrence of VIVs and the suppression of VIVs by the application of central grids. The results show that shear layers are separated from the upper railings and lower overhaul track of the upstream girder and induce large-scale vortices in the gap that cause periodical lift forces of large amplitude acting on the downstream girder, resulting in VIVs of the bridge deck. However, the VIVs are apparently suppressed by the central grids because the vortices in the central gap are reduced into smaller vortices and become weaker, causing slightly fluctuating lift forces on the deck. In addition, the mean lift force on the deck is mainly caused by the upstream girder, whereas the fluctuating lift force is mainly caused by the downstream girder.

• 한국항해학회지
• /
• 제9권2호
• /
• pp.43-63
• /
• 1985

As a circular cylinder has a comparatively simple shape and becomes a basic problem for flows around other various shapes of bodies, the problem of two-dimensional viscous flow around the circular cylinder has been investigated, both theoretically and experimentally. But not a few problems are left unsolved. It is well known that the calculations are successfully made with the approximations of Stokes or Oseen for very low Reynolds numbers, but as Reynolds number is increased, Oseen's approximations as well as Stokes's ones become more and more remote from the exact solution of the Navier-Stokes equations. Therefore, in this paper, the authors transform the Navier-Stokes equations into the finite difference equations in the steady two-dimensional viscous flow at Reynolds number up to 45, and then solve the solution of the Navier-Stokes equations numerically. Also, the authors examine the accuracy of the solution by means of flow visualization with aluminum powder. The main results are as follows; (1) The critical Reynolds number at which twin vortices begin to form in the rear of the circular cylinder is found to be 6 in the experiment and 4 in the numerical solution. (2) As Reynolds number is increased, it is proved that the ratio of the length of the twin vortices to the diameter is grown almost linearly, both experimentally and numerically. (3) Separation angle is also increased according to reynolds number. But it is found that it would converge into 101.3 degrees, both experimentally and numerically.

• 대한토목학회논문집
• /
• 제34권3호
• /
• pp.813-820
• /
• 2014

본 연구에서는 부분 식생된 개수로에서 평균흐름 및 난류구조에 관한 수치모의 결과를 제시하였다. 이를 위하여 식생항력항이 포함된 레이놀즈 평균 Navier-Stokes 방정식을 수치해석 하였고 난류 모형으로 비선형 k-${\varepsilon}$ 모형을 이용하였다. 제시된 모형을 Nezu and Onitsuka (2001)의 실험수로에 적용하여 모의된 결과를 실험 계측자료 및 Kang and Choi (2006)의 Reynolds stress model 모의결과와 비교하였다. 실험결과와 비교한 결과에 따르면, 비선형 k-${\varepsilon}$ 모형이 평균흐름의 대체적인 경향을 잘 모의하는 것으로 확인되었다. 또한, 식생 영역과 비식생 영역의 경계면에서 쌍와 (twin vortices)가 생성되고 난류강도와 레이놀즈 응력의 최대점이 위치하는 것을 확인하였다. 레이놀즈 응력에 대해서는 경향은 잘 모의하지만 정량적으로 과소 산정하는 것으로 나타났다.

• Wind and Structures
• /
• 제30권4호
• /
• pp.367-378
• /
• 2020

Two-dimensional Delayed Detached Eddy Simulation (DDES) was carried out to investigate the uniform flow over a twin-box bridge deck (TBBD) with various gap ratios of L/C=5.1%, 12.8%, 25.6%, 38.5%, 73.3% and 108.2% (L: the gap-width between two girders, C: the chord length of a single girder) at Reynolds number, Re=4×104. The aerodynamic coefficients of the prototype deck with gap ratio of 73.3% obtained from the present simulation were compared with the previous experimental and numerical data for different attack angles to validate the present numerical method. Particular attention is devoted to the fluctuating pressure distribution and forces, shear layer reattachment position, wake velocity and flow pattern in order to understand the effects of gap ratio on dynamic flow interaction with the twin-box bridge deck. The flow structure is sensitive to the gap, thus a change in L/C thus leads to single-side shedding regime at L/C≤25.6%, and co-shedding regime at L/C≥35.8% distinguished by drastic changes in flow structure and vortex shedding. The gap-ratio-dependent Strouhal number gradually increases from 0.12 to 0.27, though the domain frequencies of vortices shedding from two girders are identical. The mean and fluctuating pressure distributions is significantly influenced by the flow pattern, and thus the fluctuating lift force on two girders increases or decreases with increasing of L/C in the single-side shedding and co-shedding regime, respectively. In addition, the flow mechanisms for the variation in aerodynamic performance with respect to gap ratios are discussed in detail.

• 대한조선학회지
• /
• 제27권4호
• /
• pp.27-31
• /
• 1990

양력면(揚力面)의 양력계산(揚力計算)에 흔히 쓰이고 있는 방법(方法)을 크게 나누면 Vortex Lattice 법(法)과 Mode Function법(法)이 있다. 잘 알려진 것 처럼, Vortex Lattice법(法)은 해(解)의 수렴성(收斂性)은 좋으나 계산시간(計算時間)이 많이 걸리는 문제점(問題點)이 있고, Mode Function법(法)은 계산시간(計算時間)은 짧으나 해(解)가 특이(特異)해 지는 경우가 있다. 그러므로 본(本) 논문(論文)에서는 양방법(兩方法)의 장점(長點)들을 살리도록, 양력면(揚力面)을 Span 방향(方向)으로 분할(分割)하고 각(各) Strip Mode Function을 사용하여 Vortex를 분포(分布)시켜, 양력면이론(揚力面理論)으로 양력(揚力)을 계산(計算)하였다. 우선 Horn Type의 반균형타(半均衡舵)에 본(本) 계산법(計算法)을 적용(適用)하여 타직압력(舵直壓力)을 계산(計算)하고 타(舵) 단독시험(單獨試驗)을 병행(竝行)하여 계산법(計算法)의 유용성(有用性)을 검증(檢證)하였다. 그 결과(結果), Stall과 같은 비선형적(非線形的) 유체현상(流體現象)이 일어나지 않는 한(限), 본(本) 계산법(計算法)은 유용(有用)하다는 결론(結論)을 얻었다. 끝으로, 본(本) 계산법(計算法)을 평행(平行)하게 늘어선 한척(隻)의 장방형타(長方形舵)에 적용(適用)하여 두 타(舵) 사이의 상호간섭(相互干涉)도 계산(計算)하였다.

• International Journal of Aeronautical and Space Sciences
• /
• 제4권1호
• /
• pp.88-98
• /
• 2003

Compared to the noise limits (CAN7) specified in ICAO Annex 16 for civil helicopters, the Lynx helicopter equipped with BERP blades has only 0.2 EPNdB margin in the approach case although it has more than 4 EPNdB margin in fly-over and take-off conditions. The objectives of the study described in this paper were to devise a low noise main rotor blade for the Lynx using UEAF combined with the high resolution airload model ACROT. A design requirement is that the new blade, KBERP (Korean BERP) blade should achieve a significant reduction in noise during approach(at least 6EPNdB margin) without any noise penalty in fly-over and take-off conditions and minimal performance penalty. It was decided to investigate a tip modification to the BERP blade, employing the twin vortex concept to reduce the BVI noise and to retain the excellent high speed performance characteristics of BERP. Through the parametric study, the KBERP blade with optimized twin vortices has at least a 9 EPNdB noise margin in approach flight condition with only a small penalty in fly-over and take-off conditions. The KBERP tip is thus a very cost effective wav to reduce BVI noise during approach.

• 한국항공우주학회지
• /
• 제31권7호
• /
• pp.69-74
• /
• 2003

Vane tip 개념을 도입하여 소음 특성을 개선하도록 설계된 차세대 로터 블레이드(NRSB-I)의 공력 성능을 기존의 BERP 블레이드와 비교하기 위하여, 제자리 비행에 대한 점성 압축성 계산을 수행하였다. 깃끝 영역의 면적감소에 의하여 설계된 로터 블레이드의 절대 추력이 6-7% 정도 감소하지만, 동력계수의 감소폭이 더 크기 때문에 제자리 비행 성능상의 손실은 거의 없는 것으로 파악되었다. 또한, 깃끝 절단부에서 발생한 와류는 블레이드 표면을 지날 때 확산에 의하여 그 강도가 현저하게 약화되므로, 설계요구조건을 만족시키기 위해서는 절단부 위치에 펜스가 필요함을 확인할 수 있었다.

• Wind and Structures
• /
• 제28권5호
• /
• pp.285-298
• /
• 2019

For super long-span bridges, the aerodynamic forces induced by the flow passing the box girder should be considered carefully. And the Reynolds number sensitively of aerodynamic characteristics is one of considerable issue. In the study, a numerical study on the Reynolds number sensitivity of aerodynamic characteristic (flow pattern, pressure distribution and aerodynamic forces) of a twin-box girder were carried out using large eddy simulation (LES) with the dynamic Smagorinsky-Lilly subgrid model. The results show that the aerodynamic characteristics have strong correlation with the Reynolds number. At the leading edge, the flow experiences attachment, departure, and reattachment stages accompanying by the laminar transition into turbulence, causing pressure plateaus to form on the surface, and the pressure plateaus gradually shrinks. Around the gap, attributing that the flow experiences stages of laminar cavity flow, the wake with alternate shedding vortices, and turbulent cavity flow in sequence with an increase in the Reynolds number, the pressures around the gap vary greatly with the Reynold number. At the trailing edge, the pressure gradually recovers as the flow transits to turbulence (the flow undergoes wake instability, shear layer transition-reattachment station), In addition, at relative high Reynolds numbers, the drag force almost does not change, however, the lift force coefficient gradually decreases with an increase in Reynolds number.