• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.2
• /
• pp.27-35
• /
• 2009

The roundabout was developed in the United Kingdom to rectify problems associated with these traffic circles. In 1966, the United Kingdom adopted a mandatory "give-way" rule at alt circular intersections, which required entering traffic to give way, or yield, to circulating traffic. However, the roundabout used in United States or Europe do not common use in Korea. The purposes of the study is to comparatively analyze the effectiveness of roundabout. In pursuing the above, this study designs the scenarios which can reflect the directional traffic volumes, and analyzes the average control delay of roundabout and 4-leg signalized intersection by SIDRA. The main study results are as follows. First, when the entering traffic volume are less than 2,000pcph, the single-lane roundabout is analyzed to be more effective than 4-leg signalized intersection. Second, when the entering traffic volume are less than 3,200pcph, the double-lane roundabout is evaluated to be more effective than 4-leg signalized intersection. Third, which is installed left and right turn lane at intersection, area for the roundabout is analyzed to be less than that for general intersection area.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.5
• /
• pp.57-70
• /
• 2009

According to the change of the traffic conditions, the requirement of controlling the separated left(or right) turn, the median bus lane and bicycle signal is increasing. However, the traffic signal controller standard based on the four-set lights restricts to control the three-set lights which control the separated direction and kind of traffics. This study suggests the method to control the three-set lights signal by improving the hardware and software for the traffic signal controller which is operated currently in the traffic scene. The 6 output ports of Load Signal Unit(LSU) which is consisted of Pedestrian Red, Pedestrian Green, Red, Yellow, Arrow and Green signal reconstitute 2 rows of the Red, Yellow, Green for three-set lights while the Signal Map data's code values which control the signal step of an individual Ring and LSU are established to adjust the LSU's output ports(R1 Y1 G1 R2 Y2 G2) of the three-set lights. The effect of using the separated through/left turn and the median lane bus signal of three-set lights is analyzed from a Mangwoo intersection in Seoul. The results of analysis show that the delay time of the east-west direction where the median bus lane is operated is especially improved with over 70 sec/veh.

• Journal of Korean Society of Transportation
• /
• v.4 no.1
• /
• pp.3-11
• /
• 1986

One important element of a systematic approach to the management and control of the flow of people over an urban street network is the monitoring and evaluation of system performance. The nature of TSM strategies that, in part, differentiates them from traditional long-range transportation improvement alternatives is that they are less costly, are more quickly implemented and modified, and are often oriented toward sub-area problems which must be addressed at a more microscopic level of analysis. These factors suggest that pre-implementation evaluations of alternative TSM actions will often have to rely on quick-turn around, manual methods of analysis to guide the choice of which management action should be implemented. This paper was prepared to focus on the definition and importance of TSM, specifically associated with monitoring and evaluating traffic performance in the context of TSM startegies. A simple case study of reversible lane technique was presented. The purposes of the case study is to illustrate the methodology of evaluating TSM strategies and demonstrate to identify the benefit from the reversible lane technique, which may otherwise be overlooked in real world. Applying the reversible lane technique to Sam-Il elevate highway, it was found to be a very promising low cost alternative to reduce total travel time(or delay) and fuel consumption.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.3
• /
• pp.323-330
• /
• 2018

In this paper, design and fabrication of a MSP(Multiple Scattering Points) discriminator for a simulated target measurement using a HRR(High Range Resolution) RADAR are described. The MSP discriminator is designed to provide a reference signal at the installed point on the simulated target in an outdoor test. The MSP discriminator is designed to have a remote control function that can turn the MSP discriminator on and off when the target moves to a remote location. While the MSP discriminator is off, the MSP discriminator is designed to be small enough not to spoil the target's unique RCS. The MSP discriminator consists of RF components in the Ku-band. In order to prevent spreading of the signal, a cable were added to the MSP discriminator to have an appropriate feedback loop delay considering the resolution of the RADAR. The fabricated MSP discriminator provided a reference scattering point as an RCS of approximately 1 dBsm. As a result, by using the MSP discriminator, the physical scattering points of the target were clearly identified in the measured signals with the RADAR.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.4
• /
• pp.692-699
• /
• 2008

Semiconductor research and development(R&D) fabs are very different than production fabs in many ways such as the scales of production, job priority, production methods, and performance measures. Efficient operations of R&D fabs are very important to the development of new product, process stability, high yield, and ultimately company competitiveness. This paper proposes the fab-wide scheduling method for operational optimization of the R&D fabs. Most scheduling systems of semiconductor fabs have only focused on maximizing throughput of each separated areas without considering WIP(works in process) flows of entire fab. In this paper, we proposes the a fab-wide scheduling system which schedules all lots to entire fab equipment at once. We develop the MIP(mixed integer programing) model which allocates the lots to production equipment considering many constraints of all processes and the CP(constraint programming) model which determines the sequences of the lots in the production equipment. The proposed FAB-wide scheduling model is applied to the newly constructed R&D fab. As a result, we have accomplished the system based automated job reservation, decrease of the hot lot delay, increase of the queue time satisfaction, the high throughput by maximizing the batch sizes, decrease of the WIP TAT(Turn Around Time).

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.68-78
• /
• 2019

The emergence of high voltage conversion applications has resulted in a trend of using semiconductor device series associations. Series associations allow for operation at blocking voltages, which are higher than the nominal voltage for each of the semiconductor devices. The main challenge with these topologies is finding a way to guarantee the voltage balance between devices in both blocking and switching transients. Most of the methods that have been proposed to mitigate static and dynamic voltage unbalances result in increased losses within the device. This paper introduces a new series stack topology, where the voltage unbalances are reduced. This in turn, mitigates the switching losses. The proposed topology consists of a circuit that ensures the soft switching of each device, and one auxiliary circuit that allows for switching energy recovery. The principle for the topology operation is presented and experimental tests are performed for two modules. The topology performs excellently for switching transients on each of the devices. The voltage static unbalances were limited to 10%, while the activation/deactivation delay introduced by the lower module IGBT driver takes place in the dynamic unbalances. Thus, the switching losses are reduced by 40%, when compared to hard switching configurations.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.1
• /
• pp.27-41
• /
• 2011

This research proposes new tram signal coordination model, called MAXBAND MILP-Tram for a passive tram signal priority strategy. The proposed model was formulated based on the MAXBAND model that was a traditional arterial signal optimization model. The model could calculate the bandwidth solutions for both general-purpose-lane traffic and median-tram-lane traffic. Lower progression speed are applied for the tram traffic considering lower running speed and dwell time at the stations. A phase sequence procedure determines the green times and left-turn phase sequences for tram traffic in median tram lane. To estimate the performance of the MILP-Tram model, the control delay of trams were estimated using the micro simulation model, VISSIM. The analysis results showed 57 percent decrease of the tram compared to the conventional signal timing model. The delay for car, however, increased 18 percent. The sensitivity analysis indicated that the passive tram signal priority strategy using the offset and phase sequence optimization was effective in reducing the person delay under the congested traffic condition.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.12 no.3
• /
• pp.45-55
• /
• 2009

This study was intended to increase efficiency of traffic flow management on intersection. The result suggested to establish a left-turn at own risk lane to increase efficiency of traffic flow on intersection. The scope of the research was to investigate the geometric structure of a signal-controlled intersection, traffic volume(density) with respect to directions and traffic signal display, and to select a signalling intersection into which a car waiting for a traffic signal enters by adjusting the display sequence of traffic signal. The delay with respect to directions and for the whole intersection was compared for the current situation and an improvement plan. Using TSIS, a traffic analysis package, the traffic situation on an intersection was investigated. Based on the simulation result for Seok-Jeon intersection in Ma-San selected from the field investigation of intersections to which an improvement plans would be applicable, the waiting time in the direction without a entering traffic signal was decreased to be 78.6 seconds per car and that of the direction expecting the increase of waiting time was increased by 4 seconds per car only. It was confirmed that the waiting time for the whole intersection was improved.

• Korean Journal of Construction Engineering and Management
• /
• v.19 no.4
• /
• pp.61-69
• /
• 2018

Research on additional indirect cost due to construction period extension in general contracts has continuously been active whereas the same for the subcontract operations has not been. In this research, we review previous research on evaluation methods for additional indirect costs which are widely being used on construction sites as well as previously proposed methods altogether, applying them to analyze model-cases for comparison. We acknowledge that this pattern for construction cost fluctuation over the construction period demonstrates an S-curve. This S-curve shaped indirect cost occurrence is then used to generate model-cases that are used throughout the research which models we applied previous evaluation methods on. Finally in pursuit of finding out some problems of evaluation methods, we came to derive a conclusion that the "Average Actual Cost Evaluation Method on Extended Duration," which, in turn, were proved to be valid for application on general contracts, was also valid for general application on subcontractor operations.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.30-31
• /
• 2009

Early detection of schedule delay in field construction activities is vital to project management. It provides the opportunity to initiate remedial actions and increases the chance of controlling such overruns or minimizing their impacts. This entails project managers to design, implement, and maintain a systematic approach for progress monitoring to promptly identify, process and communicate discrepancies between actual and as-planned performances as early as possible. Despite importance, systematic implementation of progress monitoring is challenging: (1) Current progress monitoring is time-consuming as it needs extensive as-planned and as-built data collection; (2) The excessive amount of work required to be performed may cause human-errors and reduce the quality of manually collected data and since only an approximate visual inspection is usually performed, makes the collected data subjective; (3) Existing methods of progress monitoring are also non-systematic and may also create a time-lag between the time progress is reported and the time progress is actually accomplished; (4) Progress reports are visually complex, and do not reflect spatial aspects of construction; and (5) Current reporting methods increase the time required to describe and explain progress in coordination meetings and in turn could delay the decision making process. In summary, with current methods, it may be not be easy to understand the progress situation clearly and quickly. To overcome such inefficiencies, this research focuses on exploring application of unsorted daily progress photograph logs - available on any construction site - as well as IFC-based 4D models for progress monitoring. Our approach is based on computing, from the images themselves, the photographer's locations and orientations, along with a sparse 3D geometric representation of the as-built scene using daily progress photographs and superimposition of the reconstructed scene over the as-planned 4D model. Within such an environment, progress photographs are registered in the virtual as-planned environment, allowing a large unstructured collection of daily construction images to be interactively explored. In addition, sparse reconstructed scenes superimposed over 4D models allow site images to be geo-registered with the as-planned components and consequently, a location-based image processing technique to be implemented and progress data to be extracted automatically. The result of progress comparison study between as-planned and as-built performances can subsequently be visualized in the D4AR - 4D Augmented Reality - environment using a traffic light metaphor. In such an environment, project participants would be able to: 1) use the 4D as-planned model as a baseline for progress monitoring, compare it to daily construction photographs and study workspace logistics; 2) interactively and remotely explore registered construction photographs in a 3D environment; 3) analyze registered images and quantify as-built progress; 4) measure discrepancies between as-planned and as-built performances; and 5) visually represent progress discrepancies through superimposition of 4D as-planned models over progress photographs, make control decisions and effectively communicate those with project participants. We present our preliminary results on two ongoing construction projects and discuss implementation, perceived benefits and future potential enhancement of this new technology in construction, in all fronts of automatic data collection, processing and communication.