• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.125-131
• /
• 2000

The turbo chiller uses centrifugal compressor, which operates at about 14500 rpm. Due to the high rpm of the impeller, the noise of chiller makes one of the serious problems. The possibility of the sound reduction by using absorbing material is studied in this paper. The generated sound propagates through the duct and then radiates to the outer field. So, the use of sound absorption material inside the duct is one of the effective methods. To study the effect of location of the material, we use Boundary Element Method to analyze the sound field inside the duct system. Numerical study shows the highest sound pressure region is near the elbow of curved duct. From the analysis, it is also shown that the elbow duct is the main radiator of noise and sound absorption treatment of this duct results noise reduction of the highest noise level at BPF and high frequency region.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제23회 추계학술대회 논문집
• /
• pp.62-67
• /
• 2004

이 논문에서는 메탄을 연료로 하는 에어터보램제트(ATR) 엔진의 아음속 영역에서의 탈설계점 성능 해석을 수행하였다 이를 위하여 ATR 엔진을 수치적으로 모델링하여 성능을 모사하였다. 각 구성품에 대해 탈설계점 성능을 계산할 수 있도록 모델을 작성하였다. 압축기 작동점은 노즐과의 유량매칭(matching)에 의하여, 터빈 작동점은 일 매칭에 의하여 결정하였다. 성능 해석 결과, ATR 엔진은 기존의 개스 터빈 엔진과 비교해 상당히 다른 탈설계점 특성을 가지고 있음을 보였다.

• 한국분무공학회지
• /
• 제24권3호
• /
• pp.130-136
• /
• 2019

Spray visualization of a vaporizer fuel injection system of a micro turbo jet engine was experimentally studied. The fuel heating by combustion was simulated by the high pressure steam generator and combustor inlet air from the centrifugal compressor was simulated by compressed air stored in the high pressure air tank. Spray visualization was performed with single vaporizer, and then six vaporizers which are same number of micro turbojet engine were used. As a results, the spray characteristics of the vaporizer were understood with pressure difference of the combustor inlet air and the fuel supply pressure. Spray angles with three types of vaporizer configuration were measured. In the results, guide vane configuration has a wider spray angle than the straight tube and smooth curve tube with a swirler, so it is expected that the fuel will be effectively distributed inside the combustor flame tube.

• 대한기계학회논문집B
• /
• 제27권10호
• /
• pp.1427-1434
• /
• 2003

Turbo- or Super-charging has been used to boost engine power for Gasoline- and Diesel Engine since beginning of 20th century. So far turbo-charger has enjoyed a high reputation in the charging field for its technical advantages such as no demand of operation power from engine and an excellent charging effect in a static operation at mid- and high engine speed. A mechanically driven super-charger, however, is now popular due to the high engine power at quick change of the driving mode - high engine torque even at low engine speed. Since super-charger needs operation power from engine, it is difficult to improve its relatively higher fuel consumption than that of turbo-charger. This negative point is still an obstacle to the wide use of supercharger. Super-charger using screw-type compressor will fulfill the purpose to reduce fuel consumption by minimizing operation power owing to no charge at idling or part load driving condition. This study aims to develop power control concept to achieve the minimization of operation power. A screw type super-charger was modified in design partially and installed with an internal bypass valve and a bypass tube to control charging pressure at part load. The various control concepts show a possibility to reduce operation power of super-charger.

• 한국유체기계학회 논문집
• /
• 제7권3호
• /
• pp.7-13
• /
• 2004

In this paper, we identify the noise source and the path of a chiller. This chiller is newly developed for R-l34a refrigerant and 250 RT cooling capacity. The measured overall SPL of the developed turbo-chiller is about 100 dBA. Due to the high rotating speed of the centrifugal impeller, the nun noise source of the chiller is the blade passing frequency and its higher harmonics of the centrifugal impeller. This generated soundpropagates through the duct, and then transmits and radiates to the outer field. From the experiment, it is found that the high frequency noise is mostlytransmitted and radiated through the elbow duct, but the low frequency noise is transmitted and vadiated through the condenser wall. Therefore applying the absorbing material is an effective way of reducing the high and low frequency noise simultaneously. Measurement results show that the application of the sound absorbing material to the elbow duct reduced the overall sound pressure level by 4 dB compared to the 9 dBA reduction for the case of full enclosure. In order to control the generated noise, a dissipativetype silencer is also designed and tested. The silencer reduced the radiated noise about 7.5 dBA.

• 소음진동
• /
• 제9권3호
• /
• pp.593-599
• /
• 1999

A rotordynamic analysis is performed with a motor-bull gear rotor system supported on two partial bearings, which is intended to drive a high-speed turbo-chiller compressor impeller shaft through its built-in pinion gear. The motor-bull gear rotor system has a rated speed of 3,600 rpm, and is modeled utilizing the finite element method for analysis. As loadings on the bearings due to the gear action are significant in the system considered, each resultant bearing load is calculated statically by considering the generalized forces of the gear action as well as the rotor itself. The two support partial bearings are designed to take their varying loads along with their varying load angles, and they are also analyzed to give their rotordynamic coefficients. Then, a complex rotordynamic analysis of the motor-bull gear rotor-bearing system is carried out to evaluate its whirl natural frequencies and mode shapes and unbalance responses under various loading conditions. Results show that the bearings and entire rotor system are well designed regradless of operating conditions, i.e., loads and operating speeds.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.173-181
• /
• 2008

Gas turbine engine for aircraft are usually operated at the altitude condition which is quite different from the ground condition. In order to measure the precise performance data at the altitude condition, the engine should be tested at the altitude condition by a real flight test or an altitude simulation test with an altitude test facility. In this paper describes the design of altitude test facility for turbo shaft engine. This facility will be located in test cell #2 at the Korea Aerospace Research Institute. Test Cell #2 will be used for altitude testing engines with mass flow rate up to 40kg/s and inlet temperatures in the range from $-65^{\circ}C$ to $200^{\circ}C$. The existing compressor/exhauster station with heater & cooler system will be used to simulate altitude conditions in Test Cell #2.

• 한국기계가공학회지
• /
• 제14권3호
• /
• pp.141-148
• /
• 2015

The cryogenic cooling system should maintain the HTS power cable below 77 K. As the length of HTS power cables has increased, there have been many efforts to develop large capacity cryocoolers. Brayton, Joule-Thomson, and Claude refrigerators were considered for the large capacity cryocooler. Among the various cryocoolers, the Brayton refrigerator is the most competitive in terms of the HTS power cable. At present, it is thought that a 10-kW class refrigerator will be able to be used as a unit cooling system for the commercialization of HTS power cables in the near future. The Brayton refrigerator is composed of recuperative heat exchangers, a compressor, and a cryogenic turbo expander. Among the various components, the cryogenic turbo expander is the part that decreases the temperature, and it is the most significant component that is closely related with overall system efficiency. It rotates at high speed using high-pressure helium or neon gas at cryogenic temperatures. This paper describes the design of a 300-W class Brayton refrigeration cycle and the cryogenic turbo expander as a downscale model for the practical 10-kW class cycle. Flow and structural analyses are performed on the rotating impeller and nozzle to verify the efficiency and the design performance.

• Composites Research
• /
• 제29권3호
• /
• pp.111-116
• /
• 2016

터보/컴프레셔(Turbo compressor)용 틸팅 패드 저널 베어링(Tilting pad journal bearing)은 고속, 고하중의 주축(Rotor)을 지지하는 역할을 하며, 화이트 메탈(White metal)이 대표적인 소재로 널리 사용되어왔다. 그러나 예기치 않은 윤활유 공급 중단 상황(Oil cut situation) 또는 베어링과 주축 사이에 유막(Oil film)이 제대로 형성되지 않을 경우, 기존의 화이트 메탈 베어링은 융착(Seizure) 현상에 의해 바로 정지하게 되고 주축에 심각한 손상을 유발한다. 이러한 융착 문제를 해결하기 위해 기존의 화이트 메탈에 비해 높은 비강성, 비강도 그리고 뛰어난 마찰 특성(Tribological characteristic)을 가지는 탄소섬유 강화 복합재료(Carbon fiber reinforced composite)가 틸팅 패드 저널 베어링에 사용될 수 있다. 본 연구에서는 고 내열성 탄소섬유/에폭시 복합재료 틸팅 패드 저널 베어링의 오일공급 중단 상황에서의 내구성에 대한 연구를 진행하였다. 이를 위해 상온 및 오일공급 중단상황의 고온에서 인장, 압축, 전단 등의 기초적인 복합재료 물성 실험을 진행하였고, 복합재료 틸팅 패드 저널 베어링에 있어 가장 중요한 물성인 층간 계면 강도를 측정하기 위해 Short Beam Shear 실험을 진행 하였다. 오일 공급 중단 상황에서 복합재료 틸팅 패드 저널 베어링의 파손(Failure) 가능성을 알아보기 위해 유한 요소 해석(Finite element analysis)을 진행함으로써 베어링 표면에 가해지는 최대 응력을 도출하였고, 해석 결과와 물성 시험으로부터 측정된 강도 값을 이용하여 Tsai-Wu Failure index를 계산하였다. 해석 결과를 검증하기 위해 산업용 테스트 벤치를 이용하여 탄소섬유/에폭시 복합재료로 제조된 틸팅 패드 저널 베어링의 오일 공급 중단 실험을 진행하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.561-564
• /
• 2007

FCEV uses electric energy which generated from the reaction between Hydrogen and Oxygen in fuel cell stack as driving force. As fossil fuels are exhausted, fuel cell is regarded as a potent substitute for next generation energy source, and thus, most of car-makers make every efforts to develop fuel cell electric vehicle (FCEV). In addition, fuel cell is also beneficial in aspect of environment, because only clean water is produced during chemical reaction process instead of harmful exhausted gas. Generally, Hydrogen is supplied from high-pressured fuel tank, and air blower (or compressor) supply Oxygen by pressurizing ambient air. Air blower which is driven by high speed motor consumes about $7{\sim}8$ % of energy generated from fuel cell stack. Therefore, the efficiency of an air blower is directly linked with the performance of FCEV. This study will present the development process of an air blower and its consisting parts respectively.