• 한국음향학회지
• /
• 제27권8호
• /
• pp.403-410
• /
• 2008

급속한 도시인구의 증가와 교통량증가로 도로변 주거지역의 소음문제가 날로 심각해지고 있다. 본 연구에서는 도로교통량과 건축물의 위치와 형태를 고려한 소음수준을 평면적, 입체적으로 예측한다. 소음현황수준을 기초로 하여 소음원인 차량의 속도제어와 차종별 통행제한을 통한 변화치를 비교하여 개선방안을 도출하고자 한다. 분석결과 건물의 입체적분석보다 평면적 분석에서 소음환경기준치를 초과하는 면적의 비율이 높았고 주간보다 야간의 초과비율이 높게 나타났다. 개선방안은 하나의 방안을 실시했을 때보다 여러가지의 개선방안을 조합한 경우에 저감효과가 높게 나타났다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1995년도 추계학술대회논문집; 한국종합전시장, 24 Nov. 1995
• /
• pp.99-103
• /
• 1995

소음저감 설계기술은 제품의 경쟁력 향상을 위해 자동차, 항공기, 건설 장비, 선박, 심지어 가전 제품에 있어서도 소음 문제에 대한 관심이 크게 대두되고 있다. 특히 수출을 하기 위해서는 그 지역의 소음 규제법을 만족시켜야 하며 제품의 경쟁력을 위해서는 그 이상의 것이 요구되고 있다. 또한, 소음 문제는 소비자의 제품구매 선택에 영향을 주기도 한다. 일본의 경우 JIS 규격으로 건설 장비의 소음을 규제하고 있으며, 소음수준에 따라 일반 장비, 저 소음 장비, 초 저소음 장비로 구분하여 장비에 따라 건설 작업을 제한하기도 하며, 특히 초 저소음 장비 인증을 받은 것은 장비 사용 단가 및 사용에 있어 차등을 두어 혜택을 주고 있다. 본 논문에서는 현재 구미지역에서 소음규제로 사용되는 BITA 방식에 따라 지게차의 소음원 규명 및 소음 저감 대책을 논하고자 한다.

• 한국소음진동공학회논문집
• /
• 제16권11호
• /
• pp.1124-1131
• /
• 2006

This paper presents a novel method to determine sound power level(PWL) emitted by a travelling vehicle for road traffic noise simulation. The PWL is evaluated by the equivalent sound pressure level (SPL) measured by close proximity method and the sound power correction factor derived from the maximum SPL measured by pass-by method and the propagation attenuation of vehicle noise during the pass-by measurement. Using the method, we derive the empirical formula for PWL estimation in 1/1-octave and overall frequency bands for 8 vehicles (automobile, SUV, small truck, large bus, trailer, 3 dump trucks) tested at two road surfaces (dense graded asphalt, 30mm transverse tinning concrete) of Korean highway test road. The suggested approach, if securing sufficient data to represent the acoustic characteristics of all vehicle types, has il strong merit to be able to evaluate sound power levels for any combination of vehicle categories and traffic volumes.

• 동력기계공학회지
• /
• 제6권3호
• /
• pp.57-63
• /
• 2002

This paper describes the acoustic analysis of mid duty truck. The focus of the analysis is on structure borne engine noise with major contributions of 2nd order. It has been previously recognized that the noise contribution of each transfer path of structure borne noise can be varied with the charateristics of each mounts and vibro acoustic sensitivity of car body. The structure of car body will be split up into three major sub components, which are modeled separately, the engine, the frame and the cab. The acoustic performance is evaluated on three levels: engine to frame transfer, frame to cab transfer, and panel contribution from cab to driver. In order to perform these analyses, analytical models are created for the engine, frame, cab and acoustic cavity. The models are linked through a coupled fluid structure calculation, and through FRF Based Substructuring for the structural couplings. Based on the structural coupling calculations, a transfer path analysis is performed to identify the most important transfer paths. These paths are then the focussing points for applying modifications to the structure or the mount system. Finally, a number of modification are proposed and their effect is quantified.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.421-427
• /
• 2006

This paper presents a novel method to determine sound power level(PWL) emitted by a travelling vehicle for road traffic noise simulation. The PWL is evaluated by the equivalent sound pressure level(SPL) measured by close proximity method and the sound power correction factor derived from the maximum SPL measured by pass-by method and the propagation attenuation of vehicle noise during the pass-by measurement. Using the method, we derive the empirical formula for PWL estimation in 1/1-octave and overall frequency bands for 8 vehicles(automobile, SUV, small truck, large bus, trailer, 3 dump trucks) tested at two road surfaces(dense graded asphalt, 30mm transverse tinning concrete) of Korean highway test road. The suggested approach, if securing sufficient data to represent the acoustic characteristics of au vehicle types, has a strong merit to be able to evaluate sound power levels for any combination of vehicle categories and traffic volumes.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.97-102
• /
• 2008

The vibration of a vehicle, which is caused by and transmitted from the engine, has significant effect on the ride comfort and the dynamic characteristics of the engine mount system have direct influence on the vibration and noise of the vehicle. This paper examines the body shake caused by the engine excitation force on engine key on/off of a medium truck by experiment and simulation. The analysis model consists of the engine, a body including the frame, front and rear suspensions and tires. The force element between the body and the suspension is modeled as a combination of a suspension spring and a damper. The engine shake obtained from the experiment was compared with the result of the computer simulation, and by using the verified computer model, parametric study of the body shake on engine key on/off is performed with changing the stiffness of an engine mount rubber, the engine mount angle, and the position of engine mounts.

• 설비공학논문집
• /
• 제25권11호
• /
• pp.624-630
• /
• 2013

A truck refrigeration system using phase change material (PCM) is expected to have a lower noise level, reduced energy cost, and much lower local greenhouse gas emission. Recently, a forced convection type PCM refrigeration module has been developed. As the operation time increases, the PCM around the air inlet melts, because of a large temperature difference between the PCM and air. Therefore, the latent heat transfer area decreases and the heat transfer rate of the module decreases even though there is a lot of PCM which does not melt around the air outlet. A computational fluid dynamic modeling of the PCM refrigeration module was developed and validated by the experiment. Using the CFD, the design parameters, such as the mass flow rate of the air and roughness of the slab, were investigated to improve the heat transfer inhomogeneity. As a result, the adoption of partial roughness on the slabs improved the heat transfer inhomogeneity and reduced a fan power.

• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.762-767
• /
• 1998

The main torsional vibration source of the powertrain is the fluctuation of engine torque. The gear rattle is impact generating in the backlash of the free gear due to this torsional vibration. Optimization of the clutch torsional characteristic is one of the effective method to reduce the idle gear rattle. Many researches have been reported on this problem but only few of them give sufficient consideration to the detailed clutch modeling and the experiment. This paper pays attention to the optimization of clutch design parameters and the experiment to reduce the idle gear rattle vibration and noise.

• Journal of Mechanical Science and Technology
• /
• 제17권7호
• /
• pp.958-965
• /
• 2003

Structural integrity of either a passenger car or a light truck is one of the basic requirements for a full vehicle engineering and development program. The results of the vehicle product performance are measured in terms of ride and handling, durability, noise/vibration/harshness (NVH), crashworthiness and occupant safety. The level of performance of a vehicle directly affects the marketability, profitability and, most importantly, the future of the automobile manufacturer In this study, we used the virtual proving ground (VPG) approach for obtaining the dynamic characteristics. The VPG approach uses a nonlinear dynamic finite element code (LS-DYNA3D) which expands the application boundary outside the classic linear static assumptions. The VPG approach also uses realistic boundary conditions of tire/road surface interactions. To verify the predicted dynamic results, a single lane change test has been performed. The prediction results were compared with the experimental results, and the feasibility of the integrated CAE analysis methodology was verified.

• International Journal of Automotive Technology
• /
• 제2권4호
• /
• pp.135-145
• /
• 2001

DEUTZ AG, co-founded in 1864 by Nicolaus August Otto, the inventor of the four-stroke cycle engine, has developed the new 2013 engine for commercial vehicles on the basis of the tried and tested 1012 and 1013 series. With 4 and 6 cylinder models, the engine covers the power range between 100 and 190 kW. At the time of their introduction to the market, the engines will meet the exhaust emission legislation of EURO IV and incorporate the potential for EURO IV, Further engineering targets were. (Compactness, Favourable power/cost relation, Low weight, Low fuel consumption and Low noise level). All targets could be accomplished in a relatively short development period via the application of modem simulation tools and test methods. In this paper, the design configuration of the engines is described with particular emphasis on measures for noise emission reduction and the combustion system including injection and turbo charging. Furthermore, we demonstrate the engine's potential to fullfill the European emission legislation EU4, which comes into force in 2005.