• Tribology and Lubricants
• /
• v.19 no.5
• /
• pp.274-279
• /
• 2003

$Al-SiC_{p}$ composite layer was prepared by plasma thermal spray on aluminum substrate. The homogeneously dispersed composite powder for thermal spray was fabricated by mechanical alloying with ball mill. The friction tests of the composite layers and commercial aluminum alloys for comparison were performed in the temperature range of 20∼$260^{\circ}C$ with the interval of $40^{\circ}C$ with steel counter-face. Friction coefficient was recorded during test sequence, and the microstructure of surface and debris was investigated by optical and scanning electron microscope. Friction coefficients of composite and aluminum alloys at room temperature were similar except pure aluminum. As the temperature increase, friction coefficient was increased rapidly in AC4C, AC2A. But friction coefficient of $Al-SiC_{p}$ composite was not increased so much up to $220^{\circ}C$. Consequently, the reinforcement of $SiC_{p}$ into aluminum matrix increased the stability of friction coefficient as well as wear resistance.

• Tribology and Lubricants
• /
• v.16 no.4
• /
• pp.241-246
• /
• 2000

The effect of post-irradiation shelf-aging time on the wear of UHMWPE was investigated, and wear results were correlated with the time-dependent microstructural changes of polyethylene after gamma irradiation sterilization. The levels of oxidation and crosslinking in the shelf-aged acetabular liners were examined by FTIR and hot xylene extraction, respectively, and uni-directional repeat pass sliding wear tests were conducted by using a pin-on-disc wear tester. Gamma irradiation sterilization in the air environment caused an increase of oxidation, crosslinking, and wear resistance. With aging, however, oxidation progressed and decreased the level of crosslinking. This resulted in a decrease of wear resistance of UHMWPE that was accompanied with white bands and brittle cracking.

• Tribology and Lubricants
• /
• v.26 no.6
• /
• pp.322-328
• /
• 2010

An inter-propellant seal (IPS) for 75 ton class thrust turbopump was tested. Leakage characteristics were presented with a given range of pressure difference under cryogenic as well as room temperature conditions. For cryogenic tests, liquid nitrogen was used as analogic fluid of liquid oxygen (LOX) while water was used instead of kerosene for room temperature condition. Test results showed that IPS had satisfactory leakage performance. Additionally endurance test was conducted to prove the life time of manufactured IPS and the tested IPS had successfully survived during required life time, 2100 seconds.

• Tribology and Lubricants
• /
• v.29 no.6
• /
• pp.360-365
• /
• 2013

In this study, sliding wear tests were conducted to investigate the effects of tempered hardness on the sliding wear behavior of bearing steel. At a sliding speed of 0.3 m/s, the wear resistance of bearing steel with a tempered hardness of HRC 54 was superior to that with HRC 62. It was found that bearing steel with HRC 54 showed a strong tendency for the occurrence of oxidation wear at that speed, compared to that with HRC 62. This would be due to the troostitic structure of bearing steel with HRC 54, which is highly susceptible to corrosion. In this context, it is considered that sliding wear behavior could be affected by the corrosion resistance of the material.

• Tribology and Lubricants
• /
• v.29 no.2
• /
• pp.85-90
• /
• 2013

The effects of contact pressure on the sliding wear behavior of mild steel in a pin-on-disc type apparatus were investigated. Sliding wear tests were conducted with various combinations of the load and apparent area of contact. The wear behavior of mild steel as a function of sliding speed was independent of contact pressure. However, the wear rate at different sliding speeds was influenced by the load regardless of the apparent area of contact. This was attributed to the fact that there may be no difference in the real area of contact for any combination of the load and apparent area of contact.

• Tribology and Lubricants
• /
• v.29 no.1
• /
• pp.1-6
• /
• 2013

Hydraulic transmission is the main component delivering power to the drive wheels of an excavator during forward and backward movement, and it has low speed, high torque and high speed, low torque gear change ratios as a forward/backward two-speed main function. It also has additional function of ensuring that the excavator is stably fixed on the ground with the built-in parking brake during excavation operations. In this study, optimal design specifications are determined by modeling and simulating about the multi-disc-type friction clutch, which is the main component improving the reliability of the hydraulic transmission for a 14-ton wheel excavator, and the friction properties of the transmission clutch are analyzed by performing sample tests.

• Tribology and Lubricants
• /
• v.20 no.6
• /
• pp.299-305
• /
• 2004

The wear properties of clutch facing materials with two different copper amounts were evaluated against the fly-wheel materials used in clutch system, such as gray cast iron and spheroidal graphite cast iron. Sliding wear tests were carried out for four different combinations with these clutch facing materials and flywheel materials at different speeds and applied loads. Results showed that the clutch facing material contained a higher copper amount had the better wear resistance. And using the gray cast iron as the counter material, clutch facing material resulted in the much lower wear rate, regardless of the copper amount. It is obvious that the wear properties of clutch facing material are influenced from the thermal conductivities of the clutch facing material and the counter material.

• Tribology and Lubricants
• /
• v.22 no.1
• /
• pp.8-13
• /
• 2006

Sliding wear tests have been performed to evaluate the effect of normal load decrease on the wear depth of nuclear fuel rods in room temperature air. The objectives of this study are to quantitatively evaluate the supporting ability of spacer grid springs, to estimate the wear depth by using the contacting force decrease and to compare the wear behavior with increasing test cycles (up to $10^7$) at each spring condition. The result showed that the contacting load decrease depends on the spring shape and the applied slip amplitude. The estimated wear depth is smaller when compared with measured wear depth. Based on the test results, the wear mechanism, the role of wear debris layer and the spring shape effect were discussed.

• Tribology and Lubricants
• /
• v.10 no.4
• /
• pp.59-68
• /
• 1994

This study is concerned with the change of physical and chemical properties of the used oil in gasoline and LPG engine. The used oils of engine were sampled from dynamometer and cars. The field tests of car were done in city and on highway. The properties of oil were TAN, TBN, visocity, oxidation, ZDTP depletion factor and etc. Also the relation between the chemical change and antiwear property was studied. From the study, it was shown that the decrease of antiwear property of used oil was depended on the changes of ZDTP depletion factor as well as TAN (total acid number). Also, it was found that the oil used by LPG car was deteriorated within the shortest distance among the other gasoline cars. The antiwear property of oil decreased as the running distance increased. The gasoline engine oil drove mainly on highway was the least deteriorate of properities for the same running distance.

• Tribology and Lubricants
• /
• v.17 no.3
• /
• pp.209-215
• /
• 2001

In view of the effects of the hardness of material on fatigue, rolling contact fatigue process in hard metals seems to differ from it in soft metals. This paper has been aimed to compare the rolling contact fatigue process according to the hardness of materials. Rolling contact fatigue tests using the ball bearings assembled with the inner race of four different hardness have been carried out. In addition, residual stress and half-value breadth on/below the inner raceway during individual rolling contact fatigue have been measured by X-ray diffraction. The results of this study showed that the change of residual stress and half-value breadth during the rolling contact fatigue on race way in hard metals is the same as in soft metals. However, plastic deformation by rolling contact in hard metals is in microscopic scale but only for soft metals in macroscopic scale.