• Journal of the Korean Geotechnical Society
• /
• v.24 no.2
• /
• pp.5-14
• /
• 2008

Shear characteristics of quarry blasted rocks were compared using large scale direct shear tests and triaxial tests. For comparison purpose, similar test conditions were simulated as much as possible and three types of relative density (50%, 70%, 90%) were employed for the test. Results indicate that stress-strain behavior shows the same trend for two tests, but the measured shear strengths differ for the different test ms and depends on the relative density. At low relative density, the internal friction angles from direct shear test are smaller than those from triaxial tests. However, at high relative density, this phenomenon is reversed.

• Geomechanics and Engineering
• /
• v.38 no.2
• /
• pp.165-177
• /
• 2024

Liquefaction phenomenon refers to a phenomenon in which excess pore water pressure occurs when a dynamic load such as an earthquake is rapidly applied to a loose sandy soil ground where the ground is saturated, and the ground loses effective stress and becomes liquid. The laboratory repetition test for liquefaction evaluation can be performed through a repeated triaxial compression test and a repeated shear test. In this regard, this study attempted to evaluate the effects of the relative density of sand on the liquefaction resistance strength according to particle size distribution using repeated triaxial compression tests, and additional experimental verification using numerical analysis was conducted to overcome the limitations of experimental equipment. As a result of the experiment, it was confirmed that the liquefaction resistance strength increased as the relative density increased regardless of the classification of soil, and the liquefaction resistance strength of the SP sample close to SW was quite high. As a result of numerical analysis, it was confirmed that the liquefaction resistance strength increased as the confining pressure increased under the same relative density, and the liquefaction resistance strength did not decrease below a certain limit even though the confining pressure was significantly reduced at a relatively low relative density. This is judged to be due to a change in confining pressure according to the depth of the ground. As a result of analyzing the liquefaction resistance strength according to the frequency range, it was confirmed that there was no significant difference from the laboratory experiment results in the basic range of 0.1 to 1.0 Hz.

• Journal of the Korean Society for Railway
• /
• v.20 no.1
• /
• pp.64-75
• /
• 2017

The role of a track subgrade is to provide bearing capacity and distribute load transferred to lower foundation soils. Track subgrade soils are usually compacted by heavy mechanical machines in the field, such that sometimes they are attributed to progressive residual settlement during the service after construction completion of the railway track. The progressive residual settlement generated in the upper part of a track subgrade is mostly non-recoverable plastic deformation, which causes unstable conditions such as track irregularity. Nonetheless, up to now no design code for allowable residual settlement of subgrade in a railway trackbed has been proposed based on mechanical testing, such as repetitive triaxial testing. At this time, to check the DOC or stiffness of the soil, field test criteria for compacted track subgrade are composed of data from RPBT and field compaction testing. However, the field test criteria do not provide critical design values obtained from mechanical test results that can offer correct information about allowable permanent deformation. In this study, a test procedure is proposed for permanent deformation of compacted subgrade soil that is used usually in railway trackbed in the laboratory using repetitive triaxial testing. To develop the test procedure, an FEA was performed to obtain the shear stress ratio (${\tau}/{\tau}_f$) and the confining stress (${\sigma}_3$) on the top of the subgrade. Comprehensive repetitive triaxial tests were performed using the proposed test procedure on several field subgrade soils obtained in construction sites of railway trackbeds. A permanent deformation model was proposed using the test results for the railway track.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.41-50
• /
• 2011

It is well-known that pavement is easily damaged by several factors including permanent deformation and fatigue crack, causing service life of the pavement to be shorter than expected. It is very important to predict amount of permanent deformation for designing pavement and developing design method of pavement. A new model of permanent deformation of pavement materials based on concept of shear stress ratio has been proposed because the lower pavement materials are highly affected by shear strength of the material. In this study a large repetitive triaxial load test has been adapted for performing test of permanent deformation of crushed subbase materials. The test procedure which includes concept of shear stress ratio has been newly developed. Several important model parameters can be obtained from the test that can be used for making correct permanent deformation model of the material.

• Geomechanics and Engineering
• /
• v.32 no.1
• /
• pp.49-68
• /
• 2023

The three-dimensional failure criterion is essential for maintaining wellbore stability and sand production problem. The convenient factor for a stable wellbore is mud weight and borehole orientation, i.e., mud window design and selection of borehole trajectory. This study proposes a new three-dimensional failure criterion with linear relation of three in-situ principal stresses. The number of failure criteria executed to understand the phenomenon of rock failure under in-situ stresses is the Mohr-Coulomb criterion, Hoek-Brown criterion, Mogi-Coulomb criterion, and many more. A new failure criterion is the extended Mohr-Coulomb failure criterion with the influence of intermediate principal stress (σ₂). The influence of intermediate principal stress is considered as a weighting of (σ₂) on the mean effective stress. The triaxial compression test data for eleven rock types are taken from the literature for calibration of material constant and validation of failure prediction. The predictions on rock samples using new criteria are the best fit with the triaxial compression test data points. Here, Drucker-Prager and the Mogi-Coulomb criterion are also implemented to predict the failure for eleven different rock types. It has been observed that the Drucker-Prager criterion gave over prediction of rock failure. On the contrary, the Mogi-Coulomb criterion gave an equally good prediction of rock failure as our proposed new 3D failure criterion. Based on the yield surface of a new 3D linear criterion it gave the safest prediction for the failure of the rock. A new linear failure criterion is recommended for the unique solution as a linear relation of the principal stresses rather than the dual solution by the Mogi-Coulomb criterion.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.1
• /
• pp.161-173
• /
• 1999

Settlement analysis based on oedometer test results with or without Skempton-Bjerrum's modification method ( widely used for practical purposes when estimating consolidation settlements of soft clay deposits) has shortcomings that it cannot simulate real stress states and deformation behaviors of soils in case that in-situ loading and deformation conditions are not 1-dimensional. In this study, the stress path method, reflecting various probable stress paths, was employed to normally - consolidated kaolinite samples by using automated triaxial testing device which can control stress paths automatically. From this experimental study, elastic, consolidation, secondary compression and pore pressure development - dissipation behaviors under various stress paths were analyzed and deformation characteristics of soft clays, which can be the basis of rational estimation of settlements, were studied. Also by comparing results of stress path tests with those of 1-dimensional consolidation tests, limitations and problems of conventional methods were clarified.

• Journal of the Korean earth science society
• /
• v.25 no.1
• /
• pp.22-31
• /
• 2004

Laboratory experiments were conducted in order to find effects of the intermediate principal stress of ${\sigma}_{2}$ on rock fractures and faults. Polyaxial tests were carried out under the most generalized compressive stress conditions, in which different magnitudes of the least and intermediate principal stresses ${\sigma}_{3}$ and ${\sigma}_{2}$ were maintained constant, and the maximum stress ${\sigma}_{1}$, was increased to failure. Two crystalline rocks (Westerly granite and KTB amphibolite) exhibited similar mechanical behavior, much of which is neglected in conventional triaxial compression tests in which ${\sigma}_{2}$ = ${\sigma}_{3}$. Compressive rock failure took the form of a main shear fracture, or fault, steeply dipping in ${\sigma}_{3}$ direction with its strike aligned with ${\sigma}_{2}$ direction. Rock strength rose significantly with the magnitude of ${\sigma}_{2}$, suggesting that the commonly used Mohr-type failure criteria, which ignore the ${\sigma}_{2}$ effect, predict only the lower limit of rock strength for a given ${\sigma}_{3}$ level. The true triaxial failure criterion for each of the crystalline rocks can be expressed as the octahedral shear stress at failure as a function of the mean normal stress acting on the fault plane. It is found that the onset of dilatancy increases considerably for higher ${\sigma}_{2}$. Thus, ${\sigma}_{2}$ extends the elastic range for a given ${\sigma}_{3}$ and, hence, retards the onset of the failure process. SEM inspection of the micromechanics leading to specimen failure showed a multitude of stress-induced microcracks localized on both sides of the through-going fault. Microcracks gradually align themselves with the ${\sigma}_{1}$-${\sigma}_{2}$ plane as the magnitude of ${\sigma}_{2}$ is raised.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.3
• /
• pp.185-192
• /
• 2003

This study consolidation undrain Triaxial Compression Tests using constant confining pressure in clay that receive preconsolidation stress that is different and, void ratio, pore water pressure coefficient, shear strength compare with another thing theory and studied analyzing change relation of elastic modules. The summary of analysis is follows: If preconsolidation stress increases in same confining stress in relation of preconsolidation stress and deviator stress, deviator stress is proportional and increased. Can know that excess void pressure is proportional and decreases in size of preconsolidation stress in same confining stress state if preconsolidation stress increases preconsolidation stress and relation of excess void pressure. Also, over consolidated state can assume that this is thing by Dilatancy's effect though excess void pressure decreased remarkably. Preconsolidation stress and relation of stress path can know that shear strength degree increases preconsolidation stress increases, and specially, preconsolidation stress was appear in stress path form of overconsolidated state case of clay that receive at 300, 400, 500kPa in 100, 150kPa's deviator stress.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2049-2056
• /
• 2011

The reinforced-roadbed materials composed of crushed stones are used for preventing vertical deformation and reducing impact load caused by highspeed train. Repeated load application can induce deformation in the reinforced-roadbed layer so that it causes irregularity of track. Thus it is important to understand characteristics of permanent deformation in the reinforced-subbase materials. The characteristics of permanent deformation can be simulated by prediction model that can be obtained by performing repetitive triaxial test. The prediction model of permanent deformation is a key-role in construction of design method of track. The prediction model of permanent deformation is represented in usual as the hyperbolic function with increase of number of load repetition. The prediction model is sensitive to many factors including stress level etc. so that it is important to define parameters of the model as clearly as possible. Various data obtained from repetitive triaxial test and resonant column test using the reinforced-roadbed of crushed stone are utilized to develop a new prediction model based on concept of shear-stress ratio and elastic modulus. The new prediction model of permanent deformation can be adapted for developing design method of track in the future.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.2
• /
• pp.243-252
• /
• 1993

Undrained cyclic simple shear tests and undrained cyclic triaxial tests were performed on silt containing sand in order to investigate the effects of silt contents on the liquefaction strength and shear characteristics of the sand. From the view that the difference of liquefaction strength for different content of silt stems from dilatancy characteristics of the sand, stress-dilatancy relation of the sand was obtained from drained triaxial test in which the mean stress was kept constant. Considerations on liquefaction behaviors were made by comparing the drained and undrained behaviors of sands during static shear test. It is concluded that ${\lambda}$-value of the stress-dilatancy relation will be closely related to the liquefaction strength.