• 한국초전도ㆍ저온공학회논문지
• /
• 제17권1호
• /
• pp.21-24
• /
• 2015

New results of dependence of magnetic field, trapped by a stack of HTS tapes, on amount of tapes in a stack are reported. Commercial GdBCO tape 12 mm width and without Cu layer was used for the research. Tape was divided in square pieces $12{\times}12mm^2$ from which stacks were formed. Filling factor of the tape was about 1.4%. Measurements were carried out for stacks with height from 5 to 250 pieces and at wide temperature range from liquid helium to liquid nitrogen. Both FC (field cooling) and ZFC (zero field cooling) cooling methods were used in the research. These two methods show matching results with good accuracy. As a result dependences of trapped magnetic flux on amount of tapes for different temperatures were received. Research shows, that with increasing height of the stack trapped magnetic field value reach saturation at about 60 tapes in a stack for low temperatures. From 60 to 100 tapes increase of magnet flux is only 5%. Thus increase amount of tapes in a stack is not profitable. Also investigation of trapped magnet field relaxation was carried out. Relaxation speed decreases with increasing amount of elements. It means that the higher the stack is, the longer trapped flux will be held in cause of the same temperature.

• 한국초전도ㆍ저온공학회논문지
• /
• 제19권3호
• /
• pp.27-32
• /
• 2017

The effects of artificial holes on the trapped magnetic fields and magnetic levitation forces of very large single-grain $Y_{1.5}Ba_2Cu_3O_{7-y}$ (Y1.5) bulk superconductors were studied. Artificial holes were made for Y1.5 powder compacts by die pressing using cylindrical dies with a diameter of 30 mm or 40 m, or rectangular dies with a side length of 50 mm. The single grain Y1.5 bulk superconductors (25 mm, 33 mm in diameter and 42 mm in side length) with artificial holes were fabricated using a top-seeded melt growth (TSMG) process for the die-pressed Y1.5 powder compacts. The magnetic levitation forces at 77 K of the 25 mm single grain Y1.5 samples with one (diameters of 4.2 mm) or six artificial holes (diameters of 2.5 mm) were 10-17% higher than that of the Y1.5 sample without artificial holes. The trapped magnetic fields at 77 K of the Y1.5 samples with artificial holes were also 9.6-18% higher than that of the Y1.5 sample without artificial holes. The 33 mm and 42 mm single grain Y1.5 samples with artificial holes (2.5 mm and 4.2 mm in diameter) also showed trapped magnetic fields 10-13% higher than that of the Y1.5 samples without artificial holes in spite of the reduced superconducting volume fraction due to the presence of artificial holes. The property enhancement in the large single grain Y1.5 bulk superconductors appears to be attributed to the formation of the pore-free regions near the artificial holes and the homogeneous oxygen distribution in the large Y123 grains.

• 한국초전도ㆍ저온공학회논문지
• /
• 제19권1호
• /
• pp.30-35
• /
• 2017

The effects of the crystallographic orientation and sample thickness on the magnetic levitation forces (F) and trapped magnetic field (B) of single grain YBCO bulk superconductors were examined. Single grain YBCO samples with a (001), (110) or (100) surface were used as the test samples. The samples used for the force-distance (F-d) measurement were cooled at 77 K without a magnetic field (zero field cooling, ZFC), whereas the samples used for the B measurement were cooled under the external magnetic field of a Nd-B-Fe permanent magnet (field cooling, FC). It was found that F and B of the (001) surface were higher than those of the (110) or (100) surface, which is attributed to the higher critical current density ($J_c$) of the (001) surface. For the (001) samples with t=5-18 mm, the maximum magnetic levitation forces ($F_{max}s$) of the ZFC samples were larger than 40 N. About 80% of the applied magnetic field was trapped in the FC samples. However, the F and B decreased rapidly as t decreased below 5 mm. There exists a critical sample thickness (t=5 mm for the experimental condition of this study) for maintaining the large levitation/trapping properties, which is dependent on the material properties and magnitude of the external magnetic fields.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 1999년도 High Temperature Superconductivity Vol.IX
• /
• pp.358-362
• /
• 1999

Magnetic levitation forces and trapped magnetic fields of top-seeded melt growth-processed YBCO superconductors with multiseeding were studied. The number of seeds was varied from one to six. The surface magnetic field of the prepared YBCO samples was dependent on the number of the seeds. The trapped magnetic field of the top surface decreased with increasing the number of the seed. Particularly, it drastically decreased at the YBCO grain boundary, probably due to the weak rink nature of the boundary. The magnetic levitation force also decreased with increasing the number of the seeds, similar to the variation of the surface magnetic field.

• Progress in Superconductivity
• /
• 제14권1호
• /
• pp.39-44
• /
• 2012

The fabrications condition and superconducting properties of top-seeded melt growth (TSMG) processed $GdBa_2Cu_3O_{7-y}$ (Gd123) bulk superconductors were studied. Processing parameters (a maximum temperature ($T_{max}$), a temperature for crystal growth ($T_G$) and a cooling rate ($R_G$) through a peritectic temperature ($T_P$) for the fabrication of single grain Gd123 superconductors were optimized. The magnetic levitation forces, trapped magnetic fields, superconducting transition temperature ($T_c$) and critical current density ($J_c$) of the Gd123 bulks superconductors were estimated. Single grain Gd123 bulk superconductors were successfully fabricated at the optimized processing condition. The $T_c$ of a TSMG processed Gd123 sample was 92.5 K and the $J_c$ at 77 K and 0 T was approximately $50kA/cm^2$. The trapped magnetic field contour and magnetic levitation forces were dependent on the top surface morphology of TSMG processed Gd123 samples. The single grain Gd123 samples, field-cooled at 77 K using a Nd-B-Fe permanent magnet with 5.27 kG and 30 mm dia., showed the trapped magnetic field contour of a single grain with a maximum of 4 kG at the sample center. The maximum magnetic levitation forces of the single grain Gd123 sample, field-cooled or zero field-cooled, were 40 N and 107 N, respectively.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1998년도 IUMRS-ICEM ABSTRACT BOOK
• /
• pp.127.3-127
• /
• 1998

• 한국초전도ㆍ저온공학회논문지
• /
• 제24권3호
• /
• pp.19-23
• /
• 2022

We have been developing a magnetic separation device that can be used in low magnetic fields for paramagnetic materials. Magnetic separation of paramagnetic particles with a small particle size is desired for volume reduction of contaminated soil in Fukushima or separation of iron scale from water supply system in power plants. However, the implementation of the system has been difficult due to the needed magnetic fields is high for paramagnetic materials. This is because there was a problem in installing such a magnet in the site. Therefore, we have developed a magnetic separation system that combines a selection tube and magnetic separation that can separate small sized paramagnetic particles in a low magnetic field. The selection tube is a technique for classifying the suspended particles by utilizing the phenomenon that the suspended particles come to rest when the gravity acting on the particles and the drag force are balanced when the suspension is flowed upward. In the balanced condition, they can be captured with even small magnetic forces. In this study, we calculated the particle size of paramagnetic particles trapped in a selection tube in a high gradient magnetic field. As a result, the combination of the selection tube and HGMS (High Gradient Magnetic Separation-system) can separate small sized paramagnetic particles under low magnetic field with high efficiency, and this paper shows its potential application.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2001년도 학술대회 논문집
• /
• pp.139-141
• /
• 2001

YBCO superconductors were prepared by top-seeded melt growth process using various numbers of seeds. The levitation forces and trapped magnetic fields of the top surfaces of the samples were measured using Nd-B-Fe permanent magnets It was found that the processing time was greatly reduced by multiple seeding, but the properties were decreased as the number of seeds was increased. The degradation of the properties is attributed to the presence of the nonsuperconducting phases at the grain boundaries as result of the entrapment of a residual melt at grain boundaries during melt processing.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.293-297
• /
• 2000

Multiseeding with (100)/(100) grain junctions of top-seeded melt growth (TSMG) processed YBCO superconductors was studied. The effect of the number of seeds and the distance between two seeds on the levitation forces and the trapped magnetic fields of the TSMG-processed YBCO samples was investigated. Multiple seeding shortened the processing time for the fabrication of TSMC-processed YBCO superconductors. The large magnetic field was trapped at the grain junction when two seeds was placed without spacing, while the amount of the magnetic field decreased when the seed distance increased. This is attributed to the increased amount of the residual melt phases around the grain junctions.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제3권3호
• /
• pp.217-223
• /
• 2015

유체채널 내에서의 미세입자의 패터닝은 생물 및 의료 응용분야에서 활용될 가치가 높은 응용 기술이다. 본 연구는 미세유체 채널 내에서 구조물 없이 외부 자석의 배열만을 이용한 미세입자 패터닝 방법을 제안한다. 자석의 같은 극과 서로 다른 극끼리의 배열을 이용한 일렬 배열, 적층 배열 등을 고안하여, 다양한 미세입자 패터닝에 실험적으로 적용하였다. 서로 같은 극끼리의 배열은 입자 포획에 쉽게 적용 가능하여, 독립적 배열이 가능하였다. 특히 적층 배열은 다양한 패터닝을 할 수 있음을 확인할 수 있었다. 자기력 1.08mT 수준에서까지 자석 배열에 의한 일정한 패턴을 관찰할 수 있었고, 패터닝된 입자들은 20 ml/hr 의 유체 속도에서도 안정하게 유지되었다. 본 연구는 간단하면서도 자성 입자의 다양한 패터닝을 가능케 하는 방법으로 면역자기성 입자를 이용한 의학/바이오 분야로의 폭넓은 응용을 기대케 한다.