• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.213-213
• /
• 2000

A sensor system which can measure the transmittance of ITO(Indium Tin Oxide) layed glass is proposed. The sensor system includes a single wavelength laser beam source, photo diodes and electronic circuit processing sensor signal. The wavelength of laser is 543.5 m, this is most sensitive wavelength to photopic and scotopic vision. We applied the sensor to measure transmittance of ITO layer on general manufacturing environment and verified the effectiveness of sensor through experimental measurement.

• Journal of Environmental Impact Assessment
• /
• 제21권1호
• /
• pp.219-227
• /
• 2012

Daily solar radiation is essential for water resources planning and environmental impact assessment. However, radiation data is not commonly available in Korea other than in big cities, and there has been no direct measurement for rural areas where water resources planning and environmental impact assessment is usually most needed. In general, missing radiation data is estimated from nearby regional stations within a certain distance, and this study compared two dominant methods (modified Angstrom equation and transmittance interpolation method) at six stations in Nakdong River watershed area. Two methods shows a similar level of accuracy but the transmittance interpolation method is likely to be superior in that there is no need for any measurement element since the modified Angstrom equation require the sunshine hour measurement. This study will contribute to improve water resource and water quality management in Nakdong River watershed.

• Journal of the Korean Ceramic Society
• /
• 제32권6호
• /
• pp.697-702
• /
• 1995

The rough growth surfaces of diamond films fabricated by the hot filament CVD were polished using thermomechanical polishing method. And then, its application to the optical windows was discussed through the measurement of transmittance in the range of infrared radiation and analysis of surfaces structure. The results were compaerd with those of the films polished with conventional mechanicla polishing. The transmittance of the mechanically polished film reached 57~66% over the whole range from 500 to 4000 cm-1. But the transmittance of the film polished with thermomechanical polishing method was reduced below 35%. This decrease in transmittance was due to both the graphitization of diamond on the polished surface and the growth of $\beta$-SiC at diamond/Si interface during polishing. The residual Fe in hte thermomechanically polished surface was confirmed by SIMS analysis. This Fe played the role of the graphitization of near surface region of the diamond film.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.283-284
• /
• 2023

Green remodeling of pubic buildings for improving indoor environment and reducing energy consumption is increasingly promoted. The objective of this study is to measure and analyze for wall's thermal performance, thermal transmittance, of existing buildings. The method of this present study refered the ISO 9869-1 and is to measured heat flow, surface temperature of wall, and in/outdoor temperature over 7 days. And it was compared the calculated thermal transmittance with measured one. The measured wall's thermal transmittance value is about two times than the calculated thermal transmittance value.

• Journal of Institute of Control, Robotics and Systems
• /
• 제14권4호
• /
• pp.336-341
• /
• 2008

Recently, research on a flat panel display(FPD) has focused on organic light-emitting display(OLED) which has wide angle of view, high contrast ratio and low power consumption. ITO(Indium-Tin-Oxide) films are the most widely used material as a transparent electrode of OLED and also in many other display devices like LCD or PDP. The performance and efficiency of OLED is related to the surface condition of ITO coated glass substrate. The typical surface defect of glass substrate is measured for electric characteristics and physical condition for transmittance and roughness. Since ITO coated glass substrate can be destroyed for inspection about surface roughness, sheet resistance, film thickness and transmittance, precise fabrication condition should be made based on the estimated relationship. In this paper, ITO films were prepared on the commercial glass substrate by the Ion-Plating method changing the partial pressure of gas(Ar, 02) and the chamber temperature between $200^{\circ}C$ and $300^{\circ}C$. The characteristics of films were examined by the 4-point probe, supersonic thickness measurement, transmittance measurement and AFM. We estimated the relationship between processing parameters(Ar gas, O2 gas, Temperature) and properties of ITO films (Sheet Resistance, Film Thickness, Transmittance, Surface Roughness).

• Journal of Korean Ophthalmic Optics Society
• /
• 제19권4호
• /
• pp.471-477
• /
• 2014

Purpose: We have analyzed the transmittance distribution of the ocular lens using local transmittance microscope to investigate the optical homogeneity of the lens. Methods: The transmittance of the laser which is focused on the surface of the ocular lens was measured by using the photo-detector and lock-in amplifier and analyzed. Multi-coated, uncoated, and progressive lenses were analyzed. Results: In the measurement of the progressive lens and a physical stimulated lens, local transmittance microscopy analysis showed a high degree of match with the measurement results through the optical microscope. In addition, the average value of the transmittance is reduced and the standard deviation was increased in the presence of optical defects. In unstimulated lens, there are a large impact on transmittance whether the anti-reflective coating is presence or absence in both the local transmittance microscopy and general transmittance analysis. Conclusions: The distribution of the transmittance measured by local transmission microscopy were changed when the various stimulus is applied to the lenses. These analyzes by local transmission microscopy can be utilized as a way to evaluate or determine the uniformity of the coating film or lens.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• 제38권1호통권113호
• /
• pp.16-20
• /
• 2006

The effect of the freeness of pulp slurries on turbidity and transmittance of papermaking stocks was investigated using beaten bleached hardwood pulp stocks with freeness ranging from 651 mL to 403 mL CSF. Also the influence of fiber length on the turbidity and transmittance was examined with fractionated pulp stocks. Increases in stock consistency increased the turbidity. Transmittance of stock samples decreased, however, with the increase of stock consistency. Second order equations and exponential equations have been obtained as regression equations for the turbidity and transmittance of these stock samples, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제16권12호
• /
• pp.1091-1096
• /
• 2003

Ion implantation in polymeric materials can induce dramatic chemical modifications, such as bond breaking, cross linking, formation of new chemical products, which have strong influences on the macroscopic properties of the materials. In this study ion implantation was performed onto polymer, PC(polycarbonate), in order to investigate change of the optical transmittance property focusing ultraviolet ray range(200-400nm). PC was irradiated with N, Ar, Kr, Xe ions at the ion energy of 50keV and the dose range of 5 ${\times}$ 10$\^$15/, 1 ${\times}$ 10$\^$16/, 7${\times}$10$\^$16/ ions/$\textrm{cm}^2$. FT-IR, XPS, UV/Vis transmittance spectroscopy measurement technologies were employed to obtain chemical. structural properties and optical transmittance of irradiated polymer. The original PC(unimplanted) is quite transparent that it has more than 88% transmittance in the range UV-A(320∼400nm), but after ion implantation, surface colors were changed to the dark brown and the transmittance of UV ray decreased for all implantation condition, and the absorption edge was shift to visible range with increasing mass of implanted ion species and dose.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 한국윤활학회 1990년도 제12회 학술강연회초록집
• /
• pp.58-62
• /
• 1990

The size and concentration of wear debris in lubricating oil often reveal the operating condition of the rotating machinery. To evaluate the possible application of light attenuation measurement for the estimation of wear debris concentration in the lubricating oil, the light transmittance through the lubricating oil cell contaminated with various concentrations of diatomite particles was measured, the attenuation coefficient was estimated from the transmittance measurement and the coefficients were compared with those obtained from the scattering theory. The comparision showed good agreements between them. It is also noted that the experimentally determined attenuation coefficient showed almost linear relation with particle weight concentrations for the concentrations within the range of 2000 ppm. For the case of 0 ppm weight concentration of diatomite particles in the lubricating oil cell, the thickness of the cell required to give $100 \mu W$ light attenuation is 7.75 mm. This result indicates that the light attenuation method will be one of the possible candidates of machine failure diagnostic sensors for the estimation of wear debris concentration in the lubricating oil.

• Tribology and Lubricants
• /
• 제6권2호
• /
• pp.94-98
• /
• 1990

The size and concentration of wear debris in lubricating oil often reveal the operating condition of the rotating machinery. To evaluate the possible application of light attenuation measurement for the estimation of wear debris concentration in the lubricating oil, the light transmittance through the lubricating oil cell contaminated with various concentrations of diatomire particles was measured, the attenuation coefficient was estimated from the transmittance measurement and the coefficients were compared with those obtained from the scattering theory. The comparision showed good agreements between them. It is also noted that the experimentally determined attenuation coefficient showed almost linear relation with particle weight coucentrations for the concentrations within the range of 2000 ppm. For the case of 0 ppm weight concentration of diatomire particles in the lubricating oil cell, the thickness of the cell required to give $100 \muW$ light attenuation is 7.75 mm. This result indicates that the light attenuation method will be one of the possible candidates of machine failure diagnostic sensors for the estimation of wear debris concentration in the lubricating oil.