• 전자공학회논문지A
• /
• 제33A권5호
• /
• pp.65-74
• /
• 1996

in this paper, the propagation characteristics of the dominant modes in multiple coupled microstrip lines on a magnetized ferrite substrate are analyzed. The propagation constants and characteristic impedances are calculated by using the spectral domain method. With the numerical results, multi-port impedance parameters as well as scattering parameters are derived from nonreciprocal transmission line equations which are consistent with conventional transmission line theory. In additon, the numerical resutls of nonreciprocal characteristics for various values of structural, material parameters, and external magnetic fields are also presented.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 1999년도 추계종합학술대회
• /
• pp.501-504
• /
• 1999

Chua's circuit is a simple electronic network which exhibits a variety of bifurcation and attractors. The circuit consists of two capacitors, an inductor, a linear resistor, and a nonlinear resistor. In this paper, a transmitter and a receiver using two identical Chua's circuits are proposed and a synchronizations of lossless transmission line are investigated. Since the synchronization of the transmission system is impossible by coupled synchronization, the drive-response synchronization theory were used. As a result, the chaos synchronization has delay characteristics in the lossless transmission system caused by the line parameters L and C.

• Journal of Electrical Engineering and Technology
• /
• 제9권1호
• /
• pp.154-161
• /
• 2014

To study and locate partial discharge(PD) and analyze the transient state of power transformer, there is a need for a high frequency model of transformer winding and calculation of its parameters. Due to the high frequency nature of partial discharge phenomenon, there is a need for an accurate model for this frequency range. To attain this goal, a Multi-Conductor Transmission Line (MTL) model is used in this paper for modeling this transformer winding. In order that the MTL model can properly simulate the transformer behavior within a frequency range it is required that its parameters be accurately calculated. In this paper, all the basic parameters of this model are calculated by the use of Finite Element Method (FEM) for a 20kV winding of a distribution transformer. The comparison of the results obtained from this model with the obtained shape of the waves by the application of PD pulse to the winding in laboratory environment shows the validity and accuracy of this model.

• 설비공학논문집
• /
• 제6권4호
• /
• pp.344-353
• /
• 1994

This study numerically analyzed the dynamic characteristics of the frequency response on the pneumatic transmission line with load impedances. The pressure transfer function is represented by the distributed parameter line model. To validate the mathematical approximations of Bessel function ratios, the results of frequency response in a blocked line were compared with those obtained by the Infinite-product, Brown's and Square-root approximations. Special emphasis was given to the frequency response characteristics on the pneumatic transmission line with load impedances. Computations were carried out for the wide range of parameters in terms of load capacitance ratio and load resistance ratio. The present results indicated that the theoretical model is capable of accurately predicting the frequency response characteristics for any configuration of a fluid transmission line.

• 대한전자공학회논문지TC
• /
• 제47권8호
• /
• pp.61-67
• /
• 2010

일반적으로 MIS(도체-부도체-반도체)의 다층 구조로 이루어진 대칭 결합선로에 대한 해석 절차는 모드(even and odd) 해석에 기초한 특성임피던스와 전파상수를 추출함으로서 단층의 결합선로 해석 절차와 동일하다. 본 논문에서는 손실매질의 다층구조로 이루어진 마이크로 스트립선로의 손실특성의 개선을 위한 새로운 구조를 제안한다. MIS 구조로 된 전송선로의 Si와 SiO2층 사이에 0전위를 가진 도체를 일정한 간격의 주기적인 배열로 고안된 새로운 모델의 MIS구조에 대한 유한차분법을 이용한 해석방법이 사용된다. 특히 전송선로에 대한 유전체의 영향을 줄이기 위하여 0전위를 가진 주기적인 결합의 도체로 이루어진 구조가 시간영역의 신호를 통해 시험된다. 다양한 손실률을 가진 불완전 유전체에 따른 주파수 의존적인 추출된 전송선로 파라미터와 등가회로 파라미터가 주파수 함수로서 나타내진다. 특히 본 논문에서 제안한 새로운 구조의 불완전 유전체에 대한 전송선로 파라미터가 주파수 함수로 구해진다.

• Journal of Information Processing Systems
• /
• 제13권5호
• /
• pp.1358-1371
• /
• 2017

Dynamic thermal rating (DTR) system is an effective method to improve the capacity of existing overhead line. According to the methodology based on CIGRE (International Council on Large Electric systems) standard, ampacity values under steady-state heating balance can be calculated from ambient environmental conditions. In this study, simulation analysis of relations between parameters and ampacity is described as functional dependence, which can provide an effective basis for the design and research of overhead transmission lines. The simulation of ampacity variation in different rating scales is described in this paper, which are determined from real-time meteorological data and conductor state parameters. To test the performance of DTR in different rating scales, capacity improvement and risk level are presented. And the experimental results show that the capacity of transmission line by using DTR has significant improvement, with low probability of risk. The information of this study has an important reference value to the operation management of power grid.

• Wind and Structures
• /
• 제38권4호
• /
• pp.325-339
• /
• 2024

The longitudinal force resulting from tornado loads on transmission line is considered a crucial factor contributing to the failure of transmission line structures during tornado events. Accurate estimation of this longitudinal force poses a challenge for structural designers. Therefore, the objective of this paper is to provide a set of charts that can be easily used to estimate the peak longitudinal forces transferred from the conductors to a tower. The critical wind field and corresponding configuration considered in this paper are previously studied and determined. The charts should account for all the conductor parameters that can affect the value of the longitudinal force. In order to achieve that, a parametric study is first conducted to assess the variation of the longitudinal forces with different conductor parameters, based on the critical tornado configuration. Results of this parametric study are used to develop the charts that can be used to calculate longitudinal forces by adopting a multi-variable line regression. The forces calculated from charts are validated by finite element analysis. An example for the usage of the charts is provided at the end of this paper.

• 전기학회논문지
• /
• 제57권11호
• /
• pp.2041-2046
• /
• 2008

A frequency-dependent slow-wave factor (SWF) and equivalent circuit model of transmission line with defected ground structures (DGS) is described. Once S-parameters of a DGS transmission line are given, the conventional frequency -independent equivalent circuit elements are extracted using 3dB cutoff and resonant frequencies (Fc and Fo) as the first step. Using the initial equivalent elements and simple transmission line theories, a frequency-dependent equivalent transmission line model is established through an analytical method, and finally the frequency dependent SWF is calculated. The proposed equivalent circuit model and SWF are frequency-dependent and more reliable because even small insertion loss within available passband is considered, while they have been independent of frequency.

• 전자공학회논문지A
• /
• 제31A권10호
• /
• pp.39-47
• /
• 1994

In this paper, by modeling the Multilayer-Multiconductor Transmission Line(MMTL) with the characteristic parameters-effective dielectric constant, eigen modal voltages, characteristic impedances at each mode, pulse propagation characteristics of MMTL network are simulated. Transmission line modelling is performed in frequency domain, then time domain resposes are obtained by transforming the frequency domain response using fast Fourier transform.

• 산업기술연구
• /
• 제28권B호
• /
• pp.251-255
• /
• 2008

Metamaterial are artificial structures that can be designed to exhibit specific electromagnetic properties not commonly found in nature. Metamaterial transmission lines are usually fabricated with a microstrip structure and it's equivalent circuit is composed of two series capacitances and a shunt inductance. However microstrip structure need a via hall for realizing a shunt inductance. To eliminate via hall, we proposed a CRLH transmission line using a CPW structure, and obtained equivalent circuit values, line parameters.