• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.29 no.5
• /
• pp.203-207
• /
• 2019

Calcium phosphates such as hydroxyapatite (HAp), tricalcium phosphate (${\beta}$-TCP), and biphasic calcium phosphate (BCP, HAp/${\beta}$-TCP) have been prepared via hydrothermal treatment. The synthesis was conducted by reacting ($Ca(OH)_2$) aqueous solution with phosphoric acid ($H_3PO_4$) under different hydrothermal synthesis conditions (temperatures up to $150^{\circ}C$ and pH lower than 12). The effects of initial precursor Ca/P ratio (1.30, 1.50 and 1.67) and post heat treatment on the phase evolution behavior of the powders and sintered ceramics were investigated. The phases of resulting powders and sintered ceramics were controllable by adjusting the initial Ca/P ratio. A single HAp phase without any noticeable second phase was obtained for the initial Ca/P ratio of 1.67 in the overall heat treatment range. Pure ${\beta}$-TCP and biphasic calcium phosphate (HAp/${\beta}$-TCP) were synthesized from precursor solutions having Ca/P molar ratios of 1.30 and 1.50, respectively, after having been heat treated at $900^{\circ}C$ or higher. Dense ceramics with translucency were obtained at considerably lower sintering temperatures.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.38 no.2
• /
• pp.71-80
• /
• 2022

Although low translucency 3 mol% yttria stabilized tetragonal zirconia polycrystal has excellent mechanical properties, it has limited application as a monolithic prosthesis. To improve these optical limitations, translucent zirconia has improved esthetics due to an increase in the cubic phase; however, it is accompanied by a decrease in mechanical properties simultaneously. Lithium disilicate has improved its mechanical properties through crystal size reduction and various heat treatment methods; therefore, its clinical application range is continuously increasing. Translucent zirconia shows a wide distribution of physical properties depending on the yttria content and lithium disilicate according to the size and density of crystal grains. As a result, the indications for translucent zirconia and lithium disilicate are increasing. Therefore, in this literature review, we intend to examine the rationale behind the material selection criteria in clinical situations and considerations for designing fixed dental prostheses including pontic, in particular, by summarizing recent studies.

• Journal of Genetic Medicine
• /
• v.6 no.1
• /
• pp.74-80
• /
• 2009

Purpose: To assess the value of first-trimester pregnancy-associated plasma protein-A (PAPP-A), nuchal translucency (NT) and second-trimester alpha-fetoprotein (AFP), human chorionic gonadotropin (hCG), unconjugated estriol (uE3), and inhibin-A in predicting pregnancy complications other than fetal aneuploidy. Materials and Methods: A retrospective study in 3,121 singleton pregnancies with integrated testing was performed at Kangnam CHA hospital between January 2005 and December 2006. Baseline characteristics, pregnancy outcomes, and serum marker levels were obtained by review of the medical records. We analyzed the data to identify associations between the integrated screening markers and adverse pregnancy outcomes. Statistical analyses were performed with the SPSS program. Results: In preterm labor and preeclampsia, high AFP, hCG, and inhibin-A levels and low PAPP-A and NT levels were found to be significantly correlated (P<0.05). Elevated second-trimester inhibin-A levels were associated with preeclampsia (odds ratio 2.843), low birth weight (odds ratio 1.446), and preterm labor (odds ratio 1.287), and while decreased first-trimester PAPP-A levels were associated with preeclampsia (odds ratio 0.51) and preterm labor (odds ratio 0.75). Conclusion: First- and second-trimester maternal serum markers screening can be used for predicting high-risk pregnancies.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.35 no.1
• /
• pp.34-43
• /
• 1990

Six commerical rice varieties were cultivated and harvested at different locations in 1987 and 1988 to clarify the degree of locational variations. of several characteristics related to rice grain quality using the rice samples harvested from 8 to 20 locations for a variety each year. Locational variations of percent brown rice, percent milled rice, 1000-grain weight and amylose content were small, but whole grain rate, alkali digestibility, gel consistency, percent white-center and white-belly grain, degree of chalkiness and degree of translucency showed larger variations between locations. The degree of locational variation of sensory evaluation score for eating quality of cooked rice were varied from small to large along with rice variety used and year cultivated. Texture palatability index and stickiness of cooked rice among rheogram characteristics showed larger locational variations, but cohesiveness and springiness showed smaller variations between locations. Set back, break down and maximum viscosity showed larger locational variations among amylogram characteristics of rice flour. Special attention was given to a cultivated location, Anseong, because rice samples harvested at Anseong showed lower percent white-center and white-belly grain, and low set back and high break down in Chucheongbyeo, lower percent white-center and white-belly grain, higher texture palatability index and viscousness/hardness ratio, and low set back and high break down in Dongjinbyeo, higher texture palatability index, and low set back and high break down in Yongmunbyeo, lower percent white-center and white-belly grain in Sangpungbyeo, and low set back and high break down in Samkangbyeo. No other locations in this study produced rice samples showing wide acceptable quality-related characteristics except Anseong.

• Restorative Dentistry and Endodontics
• /
• v.24 no.2
• /
• pp.299-309
• /
• 1999

The composite resin, due to its esthetic qualities, is considered the material of choice for restoration of anterior teeth. With respect to shade control, the direct-placement resin composites offer some distinct advantages over indirect restorative procedures. Visible-light-cured (VLC) composites allow dentists to match existing tooth shades or to create new shades and to evaluate them immediately at the time of restoration placement. Optimal intraoral color control can be achieved if optical changes occurring during application are minimized. An ideal VLC composite, then, would be one which is optically stable throughout the polymerization process. The shade guides of the resin composites are generally made of plastic, rather than the actual composite material, and do not accurately depict the true shade, translucency, or opacity of the resin composite after polymerization. So the numerous problems associated with these shade guides lead to varied and sometimes unpredictable results. The aim of this study was to assess the color changes of current resin composite restorative materials which occur as a result of the polymerization process and to compare the color differences between the shade guides provided with the products and the actual resin composites before- and after-polymerization. The results obtained from this investigation should provide the clinician with information which may aid in improved color match of esthetic restoration. Five light activated, resin-based materials (${\AE}$litefil, Amelogen Universal, Spectrum TPH VeridonFil-Photo, and Z100) and shade guides were used in this study. Three specimens of each material and shade combination were made. Each material was condensed inside a 1.5mm thick metal mold with 10mm diameter and pressed between glass plates. Each material was measured immediately before polymerization, and polymerized with Curing Light XL 3000 (3M Dental products, USA) visible light-activation unit for 60 seconds at each side. The specimens were then polished sequentially on wet sandpaper. Shade guides were ground with polishing stones and rubber points (Shofu) to a thickness of approximately 1.5mm. Color characteristics were performed with a spectrophotometer (CM-3500d, Minolta Co., LTD). A computer-controlled spectrophotometer was used to determine CIELAB coordinates ($L^*$, $a^*$ and $b^*$) of each specimen and shade guide. The CIELAB measurements made it possible to evaluate the amount of the color difference values (${\Delta}E{^*}ab$) of resin composites before the polymerization process and shade guides using the post-polishing color of the composite as a control, CIE standard D65 was used as the light source. The results were as follows. 1. Each of the resin composites evaluated showed significant color changes during light-curing process. All the resin composites evaluated except all the tested shades of 2100 showed unacceptable level of color changes (${\Delta}E{^*}ab$ greater than 3.3) between pre-polymerization and post-polishing state. 2. Color differences between most of the resin composites tested and their corresponding shade guides were acceptable but those between C2 shade of ${\AE}$litefil and IE shade of Amelogen Universal and their respective shade guides exceeded what is acceptable. 3. Comparison of the mean ${\Delta}E{^*}ab$ values of materials revealed that Z100 showed the least overall color change between pre-polymerization and post-polishing state followed by ${\AE}$litefil, VeridonFil-Photo, Spectrum TPH, and Amelogen Universal in the order of increasing change and Amelogen Universal. Spectrum TPH, 2100, VeridonFil-Photo and ${\AE}$litefil for the color differences between actual resin and shade guide. 4. In the clinical environment, the shade guide is the better choice than the shade of the actual resin before polymerization when matching colors. But, it is recommended that custom shade guides be made from resin material itself for better color matching.

• Korean Journal of Dental Materials
• /
• v.44 no.2
• /
• pp.129-139
• /
• 2017

This study investigated the colors and mechanical properties of layered dental composites. Four nanocomposite resins (Aelite LS, Grandio, Tetric EvoCeram, Filtek Z350XT) and a silorane-based composite resin (P90) were used for overlying and underlying materials, respectively, with different thickness combinations. Colors, translucency parameter (TP), flexural and compressive properties were evaluated. All tested specimens had different color coordinates, although all were of A3 shade. Color coordinates and TP values of layered specimens better matched those of the corresponding overlying product as the thickness of the overlying product was increased. High TP values were related with high $b^*$ value differences between specimens (p<0.05). Both flexural strength and modulus, compressive strength and modulus of layered specimens with different thickness combinations were mostly lower than those of the corresponding overlying products, respectively, in their non-layered state.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.35 no.5
• /
• pp.379-386
• /
• 1990

Varietal difference of protein content in forty eight Korean recommended rice cultivars and environmental Variation in protein content of milled rice harvested at six sites of the middle and/or southern plain and four locations of mid-mountainous and/or alpine area in 1989 were investigated. Also, the composition of amino acid in milled rice was compared among three rice varieties: a high-protein japonica rice, Nongbaek, a high-protein Tongil-type rice, Yongjubyeo, and a low-protein japonica rice, Hwaseongbyeo. Korean recommended rice varieties showed 7.93% of average protein content with varietal variation from 5.5% to 10.2% for milled rice harvested in 1988, and 9.17% of mean protein content with the variation from 6.3% to 12.0% for milled rice harvested in 1989. Tongil-type rice was about 1% higher in protein content of milled rice than japonica. The low-protein japonica rice, Hwaseongbyeo exhibited lower content of essential amino acids per g of rice flour sample than the high-protein japoinica, Nongbaek and/or Tongil-type rice, Yongjubyeo, but the relative content of essential amino acids per 16.8g of nitrogen in milled rice of the former was not so different with those of the latters. Among amino acids the content of glutamic acid was highest and among essential amino acids the content of leucine was highest while methionine was lowest. The protein content of milled rice was negatively correlated with days from seeding to heading, K/Mg ratio, alkali digestion value(l-7) and amylose content, but it was positively correlated with translucency and magnesium content of milled rice. The protein content of milled rice harvested in the southern plain paddy field was about 1% higher compared with those harvested in the Middle plain. Also, the protein content of milled rice harvested in the southern mid-mountainous and alpine area was about 0.8% higher compared with those harvested in the resemble altitude area of the middle-northern part of Korea. The contribution of environmental variation to total in plain area was about 28.1% while that in mid-mountainous and alpine area was about 56.4%.

• Korean Journal of Breeding Science
• /
• v.51 no.1
• /
• pp.34-40
• /
• 2019

'Jungmo1033', a japonica rice variety, was developed by the rice breeding team at the National Institute of Crop Science (NICS) in 1992. It is derived from a cross between a native variety 'Jagwangdo', which has translucent milled rice and medium maturity; and 'Hwayeong', which is an elite line with bacterial blight resistance and mid-late maturity. The heading date of 'Jungmo1033' was August 10 in the middle plain area of Korea, which was two days later than that of 'Hwaseong'. 'Jungmo1033' has a culm length of 79 cm, which was 5 cm shorter than that of 'Hwaseong', and 105 spikelets per panicle. 'Jungmo1033' showed resistance to bacterial blight (K1, K2, and K3 races) and stripe virus, but susceptibility to the K3a race of bacterial blight, dwarf and black-streaked dwarf viruses, and planthoppers. The milled rice of this variety exhibited translucency and a medium short grain shape. It had an excellent appearance and lower amylose content (19.1%) than that of 'Hwaseong'. The characteristics related to grain milling were better than those of 'Hwaseong', especially head rice milling recovery ratio and head rice ratio (94.8%). 'Jungmo1033' showed a milled rice productivity of 5.38 MT/ha at 11 sites under ordinary cultivation conditions. (Registration No. 5723)