• 펄프종이기술
• /
• 제38권2호
• /
• pp.16-21
• /
• 2006

Uneven ink transfer of a print can be traced to several causes such as an incomplete contact between the paper surface and ink film, a coarse pattern of a continuous ink film after transfer, uneven absorption, etc. Uneven ink transfer was studied in this points by the Tollenaar. Uneven distributions of printed density are reflected in low ${\ulcorner}m{\lrcorner}$ values of the print. Tollenaar's smoothness coefficient ${\ulcorner}m{\lrcorner}$ value was important factor that deciding printed quality which was easily obtain by densitometry. Limiting print density $D_{\infty}$ that obtained Tollenaar's formulation working as a influence factor at the printed quality. In this study, we obtained limiting print density $D_{\infty}$ and smoothness coefficient ${\ulcorner}m{\lrcorner}$ value of domestic newspapers and foreign newspapers. And we analyzed about properties of the newspaper. The result of this study, smoothness coefficient ${\ulcorner}m{\lrcorner}$ value and limiting print density $D_{\infty}$ showed the good results in the low porosity and low roughness newspaper. Datum which obtained by this study was used as printability factor for the quality control and improvement of domestic newspaper and wished to apply as a basic data for the domestic newspaper quality.

• 한국인쇄학회지
• /
• 제28권2호
• /
• pp.31-44
• /
• 2010

Ever since the introduction of offset lithography, an operator have looked for ways to improve the process by reducing need for dampening solution. Lithography like off-set printing is processed using the repellent properties between water and oil, so all inks for lithography printing must work with dampening solution. The dampening solution may cause the emulsification of ink by the printing pressure in the printing nip. Emulsified ink changed viscosity, tack and causes problems such as bad transfer, uniform density and printed mottle. For a high quality web printing, we studied the effect of emulsified heat-set web inks on the printability, such as amount of ink transfer, printed density and uniformity. For this study, we were carried out by using IGT printability tester C1. For determination of ink properties using the spread meter and Thwing Albert Ink-o-meter, and using the densitometer and image analysis for printed quality determination. The experimental results of this study, we look forward to can be used as the basis for improve of the web print quality.

• 펄프종이기술
• /
• 제38권1호통권113호
• /
• pp.27-33
• /
• 2006

Newsprint is quantitatively the most important printing paper. The demands for its printability are continuously increasing. It is well known that the relationship between the physically tested paper properties and newspaper printability is unsatisfactory. In order to improve the printing quality of Korean newsprint, the printability coefficients such as maximum ink requirement(Ymax), print through were investigated. Kinds of newspapers and black printing ink were tested by IGT printability tester. Experiment condition of IGT printability tester was 14 steps between $0.2{\sim}2.8g/m^2$ of ink requirement, printing pressure was 200 N and printing velocity was 1 m/sec. The properties of newspaper samples (basis weight, bulk density, roughness, smoothness, porosity, i. e.) were examined in accordance with KS and TAPPI standard testing methods. The result of this study are respected for usefulness printing quality management of Korean newsprint.

• 한국의상디자인학회지
• /
• 제20권2호
• /
• pp.47-62
• /
• 2018

This study examined recycled fashion design utilizing natural images for application to recent trends. This study is significant in that it presents the possibility of the development of recycled women's wear design by reflecting the characteristics and expressions of natural images and using denim material, which is the most common clothing material for everyday life. The results of this study are summarized as follows. First, five types of women's clothing was produced, pursuing a natural design with a soft and feminine silhouette. Second, the colors used were blue and white, which could represent nature. Third, as for materials, this study used clothing that was to be thrown away: four pairs of denim pants and two denim dresses. This study chose denim cloth, with its great value for reuse, because of the characteristics of the strong and durable fiber, because everyone has more than one article of clothing made from denim and because it can be easily sourced. Fourth, for textile motifs, this study expressed a peaceful natural scenery with tropical animals and plants. In addition, this study further emphasized natural images using transfer media printing. This study has significance in that it presented the possibility of recycled fashion design and expanded the range of utilization using transfer media printing, a dyeing treatment to reduce the environmental burden.

• 펄프종이기술
• /
• 제39권2호
• /
• pp.31-37
• /
• 2007

Lithography like off-set printing is processed using the repellent properties between water and oil, so all inks for off-printing must work with dampening solution(water). The dampening water may cause the emulsification of ink by the printing pressure in the printing nip. This study aimed to investigate the effect of emulsified inks on print mottle. The cyan ink was emulsified artificially with the different IPA(isopropyl alcohol) content in this study. We evaluated the print mottle by densitometer and image analysis method. The print mottle phenomenon was directly affected by IPA content. The emulsification of inks also had an influence on flow properties of inks and it increased ink transfer rate. It, however, caused low ink density. Moreover the emulsified inks were spreaded to around dots and cause the thinning density on the non-printing area like print mottle. The trial printing showed that the emulsified inks also cause scumming on the printing result with little mistake of adjusting dampening solution and mostly decreasing dot reproduction. We could, therefore, find out the obvious effect of emulsified inks on print mottle.

• 한국인쇄학회지
• /
• 제26권2호
• /
• pp.1-13
• /
• 2008

Printed mottle of coated paper is one of the most common phenomenon and the most difficult problem in offset printing. Offset printing is processed mainly processed by the attractive properties between water and oil, so all inks for off-printing must work with dampening solution(water). It may cause the emulsion on the printing nip from the printing pressure. This study aimed to investigate the effect of emulsified inks on print mottle from emulsified cyan ink by force with each different IP A contents. We measured the print mottle by densitometer and image analysis method. The emulsified inks also give effect to now properties of inks and it caused more ink transfer rate, however, it caused low density of inks. Moreover the emulsified inks were spreaded to around of dots and cause the thinning density on the non-printing area like print mottle. The results showed that the emulsified inks also cause scumming on the printing result with little mistake of adjusting dampening solution and mostly decreasing dot reproduction. So we could find out the obvious effect of emulsified inks to print mottle.

• 펄프종이기술
• /
• 제44권4호
• /
• pp.77-84
• /
• 2012

The lithographic process depends on a satisfactory ink-in-water emulsion being formed during printing and the speed of wet presses makes the choice of fountain solution vitally important as the ink and fount must react quickly to form a stable emulsion. Ink and water come into contact with each other on the rolls of the press and are forced together in the roll nips. The water is not soluble in the ink since it is slightly fat. Instead, an emulsion is formed, a heterogeneous mass consisting of small water drops mixed into the ink, if the water feed is too great. This emulsification can affect the properties of an off-set ink and negatively affect the printability. So we investigated the effects of the emulsification of phenol free heat-set ink and existing heat-set ink on printed quality, such as amount of ink transfer, printed density, print-through and uniformity. We used Duke emulsification tester for the emulsification of inks, and used IGT printability tester for printed quality. The printed quality were measured by densitometer and were evaluated by the image analysis system. Compared to conventional printing ink, phenol-free ink showed better results of the printability at the emulsification.

• 펄프종이기술
• /
• 제44권2호
• /
• pp.42-48
• /
• 2012

In the 21st century, the printing industry as well as the IT industry has made rapid development. However, despite these technological advancement in the printing industry, it is still harmful for the environment, the state regulation is insufficient. Therefore, we studied the printability for the existing heat-set web inks and the newly created phenol-free eco-inks. This ink was made by reacting rosin and unsaturated dibasic acid and ester reactant, ester reactant was used instead of phenol. Printability test were used in the IGT printability tester. Experimental conditions, the temperature $22.7^{\circ}C$, humidity 57% under conditions of 0.6cc of ink supply, the print speed 1m/sec, pressures were set at 250N. As results of this study, we were able to get the following conclusions. The properties of phenol-free ink is the same as the existing inks. So we are thought to improve some characteristics such as dispersion, able to replace the existing ink.

• 펄프종이기술
• /
• 제38권4호
• /
• pp.41-46
• /
• 2006

Printed mottle of coated paper is one of the most common but the most difficult problem in offset printing. Printed mottle is caused by an uneven penetration of Ink into the paper, binder migration, etc. For a high quality printing, development of new paper coating technologies to prevent print mottle is required. So for, the study of solving printed mottle is coated paper absorption controlled by base paper sizing and coating layer binder migration control. As a results, printed mottle has improved in coated paper. But printing is worked by interaction of printing ink, coated paper and printing pressure, then we need to understand of interaction printing work and coated paper. This research focused on a way of improving printed mottle by investigating various printing conditions such as ink dispersion, nip condition and amount of ink transfer using IGT printability tester.