• Journal of Biosystems Engineering
• /
• v.36 no.6
• /
• pp.422-433
• /
• 2011

Market demand for hydro-mechanical transmission (HMT) for agricultural tractors has increased recently. To select a type of HMT satisfying design conditions, performance characteristics of 12 HMT types must be understood. This study was conducted to provide tractor engineers with a guideline to select the most appropriate HMT type for their design requirements. Characteristics on speed reduction ratio, power transmission efficiency, power regeneration, lock-up angular velocity, output torque ratio and torque ratio of planetary gear train axis of the 12 HMT types were investigated and presented as either formula or graphical forms. A guideline to select proper HMT type was also presented using 2 parameter: lock-up angular velocity (${\omega}_L$) and torque ratio of the planetary gear train axis. In addition, effect of gear ratio of the planetary gear train on the power transmission efficiency was investigated and a guideline to select the best gear ratio was also presented.

• Journal of Biosystems Engineering
• /
• v.34 no.5
• /
• pp.331-341
• /
• 2009

A double-end rod hydraulic cylinder is widely used with a steering valve for the steering control system in large tractors. For the development of automatic steering controller, the feasibility of using a proportional control valve replacing the conventional manual steering valve to control the position of hydraulic steering cylinder was investigated in terms of the max. overshoot, the steady-state error and the rise time. A simulation model for the electrohydraulic steering system with load using AMESim package was developed to be valid so that the proper control algorithm could be chosen through the computer simulation. It could be concluded that the P-control algorithm was sufficient to control the electrohydraulic steering system, where the control frequency should be no greater than 20 Hz at the P-gain of 5. In particular, the performance of the developed steering controller was satisfactory even at the conditions of varying flow rates and loads.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.3
• /
• pp.109-119
• /
• 2018

The purpose of this study is to evaluate the structural safety of the front-end loader for the 90 kW class of agricultural tractors in impact test conditions. Deformation and stress on the loader under the impact test conditions are analyzed using the commercial finite element analysis software ANSYS. In previous research dealing with the initial design of the loader, the maximum stress occurred in the mount and exceeded the yield strength of the material. In this paper, an improved design of the mount of the loader was proposed to reduce the stress concentration in the initial design. The safety of the improved design was verified by performing rigid-body dynamics analysis, transient structural analysis, and static structural analysis under three impact test conditions: a drop and catch test, a corner pull test, a corner push test. It was found that the local stress concentration in the mount that appeared in the initial design was greatly reduced in the improved design, and that the maximum stresses occurred in the three impact test conditions are smaller than the yield strength. It is expected that the design improvement of the mount proposed in this study and the method of analysis may be effectively used to enhance structural safety in the development of new model front loaders in the future.

• Asian Journal of Atmospheric Environment
• /
• v.9 no.1
• /
• pp.39-47
• /
• 2015

The emissions of ozone precursors, NOx and VOCs from a biogenic source and port-related sources (ship, shipping container truck, and cargo handling equipment) were estimated in Busan during 2013. Total biogenic isoprene emission in Busan during 2013 was estimated to be $4,434ton\;yr^{-1}$ with the highest emission (e.g., $28ton\;day^{-1}$) in summer using a BEIS method. Seasonal ozone production rates by isoprene ranged from 0.15 (winter) to 2.08 (summer) $ppb\;hr^{-1}$, contributing the predominant portion to ambient ozone levels. Total emissions of NOx and VOCs from ship traversing Busan ports were estimated to be 29,537 and $814ton\;yr^{-1}$, respectively, showing the significant contribution to total NOx emission in Busan. The emissions of ozone precursors were significantly different depending on ship tonnage and port location. Compared to the ship emission, the emissions of NOx and VOCs from the shipping container trucks in Busan were insignificant (2.9% for NOx and 3.9% for VOCs). Total NOx and VOCs emissions from the cargo handling equipment were estimated to be 1,440 and $133ton\;yr^{-1}$, respectively with the predominance of yard tractors.

• International Journal of Automotive Technology
• /
• v.7 no.5
• /
• pp.535-545
• /
• 2006

A nonlinear analysis of torsional self-excited vibration in the driveline system for wheeled towing tractors was presented, with a 2-DOF mathematical model. The vibration system was described as a second-order ordinary differential equation. An analytical approach was proposed to the solution of the second-order ODE. The mathematical neighborhood concept was used to construct the interior boundary and the exterior boundary. The ODE was proved to have a limit cycle by using $Poincar\'{e}-Bendixson$ Annulus Theorem when two inequalities were satisfied. Because the two inequalities are easily satisfied, the self-excited vibration is inevitable and even the initial slip rate is little. However, the amplitude will be almost zero when the third inequality is satisfied. Only in a few working modes of the towing tractor the third inequality is not satisfied. It is shown by experiments that the torsional self-excited vibration in the driveline of the vehicle is obvious.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.1176-1185
• /
• 1993

The purpose of this study is to propose a new dynamic model of wheels and agricultural tractors through verification of the existence of " lift resistance " and "perpendicular adhesion" which also can be called " contra-retractive adhesion". The existence of these forces was proved through experiments including the development of a sensor which can measure the forces acting on a wheel accurately. Consequently " perpendicular adhesion ratio" which is defined as the ratio of the perpendicular adhesion to the distributed load was observed to be in the range of 0.05 to 0.3. This means the influence of the " lift resistance " is comparable to that of motion resistance in wheel dynamics. The perpendicular adhesion ratio was observed to decrease logarithmically with the increase of ground contact pressure, and to increase linearly with increase of the travel speed of the wheel . Some examples to express the new dynamic model compared to the conventional dynamics are explained.

• Journal of Biosystems Engineering
• /
• v.26 no.6
• /
• pp.509-516
• /
• 2001

This paper introduced some advantages of the time-frequency analysis of vibration and investigated, using the time-frequency transform, the characteristics of the transient motion of a tractor seat, which occurred during the tractor traversed over a rectangular obstacle on the flat surface. The characteristics of the short-time courier and wavelet transforms as time-frequency analysis methods were introduced and discussed to figure out which is more suitable to the analysis of the transient motions of agricultural tractors. Using each transform, transient vibration of a tractor seat was analyzed. Results of the analysis showed that the transient vibration of the seat was influenced by the natural frequencies of vertical mode of chassis, pitching mode of engine and pitching mode of cab of the tractor. The time sequence of the natural mode of tractor vibration was also revealed by the time-frequency analysis. The vibration path analysis by the time-frequency transform showed that the vibration energies transmitted from the front mounts to the seat were less than those from the rear mounts. The energy reduction ratios between the cab mounts and seat were also estimated to be about 72∼78%. The front mounts showed larger reduction than the rear mounts. However, the reduction difference between the right and left sides mounts was negligibly small. The short time Fourier transform was found to be a proper method for investigating the transient motions of farm machines and their effects on the ride vibration.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.538-545
• /
• 1993

Individual farming involving small land parcel (0.5 to 1.0ha) is declining because it is uneconomic and unable to incorporate modern technological innovation to improve its production efficiency. A centrally managed medium scale mechanised rice share farming was implemented at Permatang Pauh, Sebeerang Perai, Malaysia in 1988-1991 for eight seasons on a contiguous 57 ha rice land rented from 100 owners. Ten participants were chosen to participate in this project which perpetuated from revolving fund of MR 165.000. The objective of the project was to overcome problem of production efficiency and to provide a stable income to farmers operating on a medium and full time basis. Mechanisation was given prime emphasis to optime and reduce labour requirement and meeting the targeted crop scheduling. Direct seeding and mechanical transplanting methods of crop establishment were adopted. Land preparations, crop establishment and crop care were done using machineries purchased by the group. Selected participants were trained to operate machineries which composed 2 and 4 wheel tractors, mechanical transplanters, motorised seeders and sprayers. Harvesting and transportation of rice to the mills were done on contractual basis using combine harvesters and bulk handling via 3-4 ton lorries respectively. The net clean yield (less 10-20 percent deduction at rice mills) obtained in such project has contributed to stabilise the production and income of participating farmers.

• Journal of Navigation and Port Research
• /
• v.35 no.1
• /
• pp.71-76
• /
• 2011

Recently, container terminal managers make an experiment on the double cycle and dual cycle operation, which ship loading and unloading were carried out simultaneously, for increasing the productivity of quay side. If, however, we make an experiment on dual cycle operation in a real job site, the efficiency is poor up to terminal operation method as YTs(Yard Tractors)' allocation method, QCs(Quay Cranes)' working speed, and position of export containers. Especially, using the existing yard operation method, it is difficult to support to dual and double cycle operation. Therefore, this paper examine more efficient terminal operation method, when terminal uses dual cycle operation. We developed a simulation model using simulation analysis software, Arena.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2011.11a
• /
• pp.170-171
• /
• 2011

Recently, container terminal managers make an experiment on the double cycle and dual cycle operation, which ship loading and unloading were carried out simultaneously, for increasing the productivity of quay side. If, however, we make an experiment on dual cycle operation in a real job site, the efficiency is poor up to terminal operation method as YTs(Yard Tractors)' allocation method, QCs(Quay Cranes)' working speed, and position of export containers. Especially, using the existing yard operation method, it is difficult to support to dual and double cycle operation. Therefore, this paper examine more efficient terminal operation method, when terminal uses dual cycle operation. We developed a simulation model using simulation analysis software, Arena.