• Structural Engineering and Mechanics
• /
• 제51권1호
• /
• pp.67-88
• /
• 2014

It is shown that topology optimization is a valuable tool for the design of bridge girders. This paper is a follow-up to (Kuty${\l}$owski and Rasiak 2014) and it includes an analysis of truss members' outer dimensions dictated by the standards. Moreover, a frame bridge girder mapped from a selected topology is compared with a typical frame girder on the basis of (Kuty${\l}$owski and Rasiak 2014). The analysis shows that topology optimization by means of the proposed algorithm yields a topology from which one can map a frame bridge girder requiring less material for its construction than the typical frame girder currently used in bridge construction.

• 한국생산제조학회지
• /
• 제19권2호
• /
• pp.224-229
• /
• 2010

This paper presents a reliability-based topology optimization (RBTO) using bi-directional evolutionary structural optimization (BESO). An actual design involves uncertain conditions such as material property, operational load and dimensional variation. Deterministic topology optimization (DTO) is obtained without considering of uncertainties related to the uncertainty parameters. However, the RBTO can consider the uncertainty variables because it has the probabilistic constraints. In this paper, the reliability index approach (RIA) is adopted to evaluate the probabilistic constraint. RBTO based on BESO starting from various design domains produces a similar optimal topology each other. Numerical examples are presented to compare the DTO with the RBTO.

• 융복합기술연구소 논문집
• /
• 제5권2호
• /
• pp.7-12
• /
• 2015

A novel topology for the magnet gear is proposed in this study. Differently from the existing methods, both sides of magnet array in this topology are used, resulting in increasing the efficiency of the mechanism. The closed magnetic path between the magnetic elements decreases the leakage flux, so the interlinking magnetic flux through the air-gap is focused and intensified. This paper discusses the dominant parameters of the proposed magnet gear influencing the resulting transmission torque. The parameters are designed from the sensitivity analysis using the commercial FEM analysis tool. And, the test setup for verifying the performance of the system is described.

• 전력전자학회논문지
• /
• 제24권4호
• /
• pp.229-236
• /
• 2019

This study proposes a DC-DC converter topology of solid-state transformer for low-voltage DC distribution. The proposed topology consists of a voltage balancer and bipolar DC-DC converter. The voltage and current equations are obtained on the basis of switching states to design the controller. The open-loop gain of the controller is achieved using the derived voltage and current equations. The controller gain is selected through the frequency analysis of the loop gain. The inductance and capacitance are calculated considering the voltage and current ripples. The prototype is fabricated in accordance with the designed system parameters. The proposed topology and designed controller are verified through simulation and experiment.

• 자동차안전학회지
• /
• 제14권4호
• /
• pp.27-34
• /
• 2022

In the development of automated driving, interest in the interior parts of vehicle is to become more significant in terms of the occupant safety and comfort. This study proposed an optimal design of front seat according to the design requirements for frame stiffness and seat comfort. For the seat comfort, the appropriate foam thickness was obtained using the structural analysis under reclined occupant loadings. While the strength and stiffness analyses were performed to evaluate the seat frame structure. Topology optimization was carried out based on the simulation results and the derived optimal model and baseline seat design was updated. The conceptual seat design for the autonomous vehicle in this study showed that the model development process is appropriate for the design parameters in both frame stiffness and seat comfort.

• 전기학회논문지
• /
• 제63권11호
• /
• pp.1519-1525
• /
• 2014

This paper presents the shape design for reducing cogging torque and characteristic analysis in Brushless DC (BLDC) motor. In this BLDC motor, ${\Delta}$(delta)-winding is applied, and in order to obtain the $60^{\circ}$ trapezoidal phase back-EMF waveform, permanent magnet shape design is carried out. And then, a method on specifying design parameters to effectively reduce cogging torque is developed. back-EMF, input voltage and input current which are analyzed by the Finite Element Method (FEM) are validated by experimental results. Also, efficiency calculations based on analysis and experimental results are performed and analyzed.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2008년도 정기총회 및 학술발표대회
• /
• pp.755-758
• /
• 2008

Currently, the increased run-off and the shortened arrival time are one of the causes of the city environmental disasters in urbanization. Therefore, it is necessary to properly design the hydrologic structures, but it is very difficult to forecast the values necessary to design from the planning stage. Moreover, as the parameter is changed due to the urban development, it is difficult not only to analyze the run-off influences but also to find the related studies and literatures. The purpose of this study is to utilize the results as the important basic data of the hydrologic structures, its proper design and run-off influences through the sensibility analysis of the model parameter variables. In this study, the absolute and relative sensibility analysis method were used to find out the correlation through the sensibility analysis of the topology and hydrology parameters. Especially, in this study, the changes in the run-off amount and volume were calculated according to increase/decrease in CN, the coefficient of discharge, and the empirical formula is prepared and proposed through the regressive analysis among the parameters. In the meantime, the parameter sensibility analysis was performed through the simulation HEC-HMS that is used and available in Korea. From the results of this study, it was found that the run-off amount is increased about by 10% when the CN value is increased by 5% before and after the development through the HEC-HMS simulation and data analysis. As long as there will be additional data collection analysis and result verification, and continuous further studies to find out the parameters proper to the domestic circumstances, it is expected to considerably contribute to the proper design of the hydrologic structures with respect to the ungauged basin.

• 대한기계학회논문집A
• /
• 제36권11호
• /
• pp.1335-1343
• /
• 2012

논문은 위상최적화와 치수최적화 해석기법을 이용한 샌드위치 복합재와 알루미늄 압출재로 구성되는 하이브리드 철도차량 차체 구조물의 경량 모듈화 설계에 관한 연구이다. 위상최적설계는 초기설계단계에 차체 구조물의 최적의 재료적용부위를 선정하기 위해 사용되었으며, 치수최적화설계는 하이브리드 차체 구조물의 최적 설계 변수를 찾기 위해 사용되었다. 이때, 최적화해석은 일계법과 부분문제근사법을 사용하였다. 위상최적설계해석을 통해 차체 구조물의 강성 및 제작성을 향상시키기 위한 언더프레임, 로우 사이드 패널 모듈에 1차 부재인 알루미늄 압출재의 적용이 적절하고, 샌드위치 복합재는 무게를 최소화하기 위한 2차 부재로서 루프 및 미들 사이드 패널 모듈에 적용이 적합하다는 결론을 얻었다. 또한, 알루미늄 압출재와 샌드위치 복합재로 구성되는 하이브리드 차체 구조물의 무게는 샌드위치 복합재로만 만들어진 차체 구조물과 비교하여 최대 17.7%까지의 경량화 효과를 얻을 수 있음을 확인하였다.

• Journal of Power Electronics
• /
• 제18권3호
• /
• pp.902-909
• /
• 2018

This study investigates the influences of different core parameters on the dynamic performances, such as rise time and overshoot, in pulse transformers for the triggering circuit of SCRs. First, a simplified transformer equivalent circuit, which emerges from a standard transformer equivalent circuit, is developed to analyze the step response. Second, the relations between the dynamic performances and the parasitic parameters are calculated by the simplified equivalent circuit. Third, the variations of rise time and overshoot, which are vital to the stability of triggering SCRs, with different core parameters, such as mechanic dimensions and topologies, are comprehensively investigated by analyzing the parasitic parameters. Finally, prototype transformers are fabricated to experimentally validate the analysis. The presented method can practically instruct the design of a pulse transformer for triggering SCRs.

• Tribology and Lubricants
• /
• 제32권6호
• /
• pp.207-211
• /
• 2016

To interpret the perception that originates from tactile sensibility during people touch and recognize the object surfaces, this study focuses on the development of a friction model that can describe the interaction of a stylus pen sliding over the counter surfaces. In addition, the study includes several other experimental factors such as the pressure, temperature, and topology of surface, which can have an effect on the emotional user experience concerning various surfaces; this research aims to suggest a method to quantitatively evaluate the relation between these experimental parameters and emotional user experience. Accordingly, the objective of research comprises the friction characteristic technology for measurement of fine tribological behavior and a standard to quantify the emotional feedback. Existing panels or input devices that provide interaction feedback about user actions simply operate with a single frequency vibration or sound response. On the contrary, this research investigates various interaction characteristics including friction force, frequency, and surface topology synthetically. Using the developed model, which can explain the relation between the friction parameters and emotional user experience, developers can design their product in order to provide the user with expected emotional sensibility. Consequently, it can contribute to reduce the development cost about sensitivity model.