• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.3
• /
• pp.215-226
• /
• 2017

This paper presents numerical results of the performance of a marin propeller in cavitating and non-cavitating flow conditions. The geometry and experimental validation data of the propeller are provided in Potsdam Propeller Test Case(PPTC) in the framework of the second International Symposium on Marine Propulsors 2011(SMP'11) workshop. The PPTC includes open water tests, velocity field measurements and cavitation tests. The present numerical analysis was carried out by using the Reynolds averaged Navier-Stokes(RANS) method on a wall-resolved grid ensuring a y+=1, where the SST k-${\omega}$ model was mainly used for turbulence closure. The influence of the turbulence model was investigated in the prediction of the wake field under a non-cavitating flow condition. The propeller tip vortex flows in both cavitating and non-cavitating conditions were captured through adaptation of additional grids. For the cavitation flows at three operation points, Schnerr-Sauer's cavitation model was used with a Volume-Of Fluid(VOF) approach to capture the two-phase flows. The present numerical results for the propeller wake and cavitation predictions including the open water performance showed a qualitatively reasonable agreement with the model test results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.36-43
• /
• 2017

The results of a numerical study on the performance of a propeller operating near a free surface are presented in this paper. The simulations are verified through comparison with experimental data, which was performed in a circulating water channel. The propeller performance as a function of the submerged depth was investigated. The effect of the propeller advance ratio on the wave patterns, flow structures around propeller, and thrust and torque of the propeller was also studied. Air ventilation was not observed for low advance coefficients. However, the simulations showed that wave pattern was strongly related to the tip vortex strength and inflow velocity. When air ventilation does not occur, the deduction of propeller thrust and torque increase for high advance coefficients.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.3 s.108
• /
• pp.291-297
• /
• 2006

The BVI(blade vortex interaction) noise Prediction has been one of the most challenging acoustic analyses in helicopter aeromechanical Phenomenon. It is well known high resolution airloads data with accurate tip vortex positions are necessary for the accurate prediction of this phenomenon. The truly unsteady time-marching free-wake method, which is able to capture the tip vortices instability in hover and axial flights, is expanded with the rotor flapping motion and trim routine to predict unsteady airloads in forward and descent flights. And Farassat formulation 1-A based on the FW-H equation is applied for the noise prediction considering the blade flapping motion. Main objective of this study is to validate the newly developed prediction code. To achieve the objective, the descent flight condition of AH-1 OLS(operational loads survey) configuration is analyzed using present code. The predicted sectional thrust distribution and sectional airloads time histories show the present scheme is able to capture well the unsteady airloads caused by a parallel BVI. Finally, the predicted noise data, observed in two different positions where are 3.44 times of rotor radius far from the hub center, are quite reasonable agreements with the experimental data compared to the other analysis results.

• Advances in aircraft and spacecraft science
• /
• v.10 no.2
• /
• pp.107-125
• /
• 2023

Drag reduction is significant research in aircraft design due to its effect on the cost of operation and carbon footprint reduction. Aircraft currently use conventional solid winglets to reduce the induced drag, adding extra structural weight. Fluidic on-demand winglets can effectively reduce drag for low-speed flight regimes without adding any extra weight. These utilize the spanwise airflow from the wingtips using hydraulic actuators to create jets that negate tip vortices. This study develops a computational model to investigate fluidic on-demand winglets. The well-validated computational model is applied to investigate the effect of injection velocity and angle on the aerodynamic coefficients of a rectangular wing. Further, the turbulence parameters such as turbulent kinetic energy (TKE) and turbulent dissipation rate are studied in detail at various velocity injections and at an angle of 30°. The results show that the increase in injection velocity shifted the vortex core away from the wing tip and the increase in injection angle shifted the vortex core in the vertical direction. Further, it was found that a 30° injection is efficient among all injection velocities and highly efficient at a velocity ratio of 3. This technology can be adopted in any aircraft, effectively working at various angles of attack. The culmination of this study is that the implementation of fluidic winglets leads to a significant reduction in drag at low speeds for low aspect ratio wings.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.3
• /
• pp.17-26
• /
• 2002

The pressure distributions on a semi-span wing 1/12 scale mode and sic component aerodynamic forces and moments on a complete 1/16 scale advanced trainer model were measured. To reduce wing-tip vortex strength, 3 wing-tip jet slot shaped(forward $35{^{\circ}C}$ direction, straigt direction, backward $35{^{\circ}C}$ direction) and 3 blowing coefficents (0.004, 0.009, 0.017) were considered. From experiment results, the case of straight direction and blowing coefficent of 0.017 was the best effective in the reduction of drag and in increase of lift-drag ratio and A rate of drag decrease and a rate of lift-drag ratio increase were of most effective on angle of attack 8 degree.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.4
• /
• pp.337-345
• /
• 2008

this study, three dimensional surface pressure distributions of SWIM whose main wing has NACA4412 airfoil with NACA0012 flaps were experimentally measured by pressure sensitive paint. Surface pressures on suction and pressure sides of the wing were measured by changing an angle of attack at a Reynolds number of 3.1x105 in KARI 1m subsonic wind tunnel. The experimental results showed that as an angle of attack increases minimum pressure region on a suction side moved from the wing root to the tip and low pressure region around trailing edge of the wing tip which causes wing tip vortex was observed. Although low pressure region at the tip still observed at an angle of attack 15 deg., other area on a suction side showed flat pressure distribution in a span-wise direction. It was also observed that the mean value of pressure coefficients was about 0.077 through a comparison between PSP and pressure taps at the same test conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.2
• /
• pp.94-101
• /
• 2016

In this paper, aerodynamic effects on the flow field under the wing with varying aspect ratio were investigated by measuring pressures on the lower surface of wing and analysing velocity components using Particle Image Velocimetry at Reynolds numbers of $1.384{\times}10^5$ and $2.306{\times}10^5$. In case of aspect ratio 4.8 which keeps the wing tip at a distance of 80% chord length from the pylon, the vortex from the wing tip influenced the flow field under the wing by reducing static pressures on the lower surface and increasing the velocity in proximity of the wing tip. Throughout the results, it is observed that aerodynamic effects of wing tip on the flow field around pylon under wing become insignificant as the aspect ratio increases.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.1
• /
• pp.1-7
• /
• 2014

The present study numerically investigated the effect of the advance ratio on the wake characteristics of the marine propeller in the propeller open water test. Therefore, a wide range of the advance ratio(0.2${\kappa}-{\omega}$SST Model are considered. The three-dimensional vortical structures of tip vortices are visualized by the swirl strength, resulting in fast decay of the tip vortices with increasing the advance ratio. Furthermore, to better understanding of the wake evolution, the contraction ratio of the slip stream for different advance ratios is extracted from the velocity fields. Consequently, the slip stream contraction ratio decreases with increasing the advance ratio and successively the difference of the slip stream contraction ratio between J=0.2 and J=0.8 is about 0.1R.

• Journal of Power System Engineering
• /
• v.21 no.5
• /
• pp.20-28
• /
• 2017

The steady-state, incompressible and three-dimensional numerical analysis was performed to investigate the flow fields around the seabed tiller used for soil improvement in coastal fisheries and the pulling force and buoyancy generated by tiller operation. The turbulence model used in this study is a realizable $k-{\varepsilon}$. As a results, at a stationary current or a current speed of 1.2 knots, where rotor rotates in a clockwise direction, a typical vortex pair appears near the tip of the rotor except for the edge, and the strength of the vortex pair increases with the number of revolutions of the rotor. The pulling force of the tiller rotating in the counterclockwise direction increases with the number of revolutions. Also, when the current flows at 1.2 knots and the rotor rotates clockwise, the pulling force of the tiller acts on the upstream side irrespective of the number of rotations of the rotor, so that no force is applied. The buoyancy of the tiller acts on the seawater surface if the flow direction inside the rotor is the same as the direction of rotation of the rotor, regardless of the current velocity, otherwise it acts on the seabed.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.2 s.41
• /
• pp.32-40
• /
• 2007

The present study investigated local pressure drop in a rotating smooth square duct with turning region. The duct has a hydraulic diameter $(D_h)$ of 26.7mm and a divider wall of 6.0mm or $0.225D_h$. The distance between the tip of the divider and the outer wall of the duct is $1.0D_h$. The Reynolds number (Re) based on the hydraulic diameter is kept constant at 10,000, and the rotation number (Ro) is varied from 0.0 to 0.20. The pressure coefficient distribution $(C_p)$, the friction factor (f) and the thermal performance $({\eta})$ are presented on the leading, the trailing and the outer surfaces. It is found that the curvature of the $180^{\circ}-turn$ produces Dean vortices that cause the high pressure drop in the turning region. The duct rotation results in the pressure coefficient discrepancy between the leading and trailing surfaces. That is, the high pressure values appear on the trailing surface in the first-pass and on the leading and side surfaces in the second-pass. As the rotation number increases, the pressure discrepancy enlarges. In the fuming region, a pair of the Dean vortices in the stationary case transform into one large asymmetric vortex cell, and then the pressure drop characteristics also change.