• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2005년도 춘계 학술기술논문발표대회 논문집
• /
• pp.173-178
• /
• 2005

The tile construction methods for existing have been used materials within limit which adhesion by wet method in masonry wall and concrete structure. These existing adhesive tech can caused many problems in construction of large and reform tile, after that it can be happened loose scale, peel off, falling off tile by heat and vibration or impact. In according to, this study is to test tile for bond stability, adhesive property by impact, vibration. low property by heat and then, we have the results as below; (1) The tile adhesive stability can be effected as adhesive area between bond agent and tile, adhesive area can more wide and press enough to ensure property. (2) Existing adhesive strength and standard relative tile construction is limited to adjust performance tile on the concrete and masonry wall. In summary, It is necessary to establish standard of performance and test method to ensure tile adhesive salability in dry wall.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 가을 학술논문 발표대회
• /
• pp.153-154
• /
• 2020

This study aims to find out the reason that tile adhesive(type III) for ceramic tile does not harden under some conditions especially high humidity even though long curing time. Bonding strength of adhesive between substrate and ceramic tile is evaluated depending on bonding conditions such as substrate kind(concrete, board), bonding material (tile adhesive, tile cement) and curing condition(humidity 50, 70%). Based on the results, this study aimed to establish the quality of tile adhesion strength under the relevant conditions.

• 한국건축시공학회지
• /
• 제2권3호
• /
• pp.163-170
• /
• 2002

Recently, polishing tile(porcelain homogeneous polished tile) was used in the construction field as a finishing material. But, there happened some problems such as tile exfoliation by construction condition in early ages. Also, for use of polishing tile in the dry wall system which used to lightweight wall, the examination of adhesive stability of polishing tile is needed. In this study, adhesive strength of Polishing tile was investigated by tile bond types on gypsum board and non asbestos board coated by tar-urethane and Polymer modified cementitious waterproofing membrane(Series I). Then, the effect of heat stress and vibration was estimated on gypsum and non asbestos board(Series II). As the result of study are the follows; (1) Polishing tile(600$\times$400mm) construction on waterproofing layer : Both laboratory estimation and spot examination sieve were happened that fall of tile because their hardening speed is late. (2) To using powder style adhesives in the dry wail with waterproofing layer : Adhesive strength of tile is Influenced by interface bond area and base side condition. (3) Shock and heat stresses : obvious decline of adhesive strength is not happened

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2020년도 봄 학술논문 발표대회
• /
• pp.128-129
• /
• 2020

In this study, flexural strength and tile adhesion strength were evaluated by using a mortar, dry mortar and an epoxy resin reinforced mortar to examine the adhesion performance by reinforcing the epoxy resin adhesive. As a result, it was clearly confirmed that the effect of improving the adhesion strength by reinforcing the epoxy resin adhesive regardless of the type of tile, and in particular, when applying the epoxy resin adhesive to the porcelain and polishing tiles, it is judged that sufficient adhesion performance can be secured.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2008년도 추계 학술논문 발표대회
• /
• pp.13-16
• /
• 2008

This paper is to present the performance data for improved direct setting method using tile bond for application of porcelain tile under 1 percent absorptance. For this purpose, improved direct setting method type 1 & 2(tile bond curing time 0, 24H) were compared with the conventional setting methods(including direct setting method and improved pressure setting method) in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion, heat ageing(70℃) and freeze-thaw cycle. On the basis of test results, the adhesive strength of direct setting method was lowest for the conventional setting methods. But improved direct setting method using tile bonds(A, B) came close to the result of improved pressure setting method using tile bonds.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 봄 학술논문 발표대회
• /
• pp.183-184
• /
• 2021

Defects such as falling and cracking of tiles installed in the bathrooms of apartment houses are frequently occurring. Therefore, in order to solve this problem, the A/S cost of construction companies and consumer complaints are increasing. The causes of tile defects include problems such as the selection of tile adhesive and lack of adhesive strength, the carelessness of the installer, the base surface, and the absorption rate of the tile. Therefore, in this study, an adhesive construction method using tile adhesives with high resistance to deformation of floors and tiles was studied. In addition, the properties and construction methods of tile adhesives were evaluated.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2009년도 춘계 학술논문 발표대회 산업계
• /
• pp.99-102
• /
• 2009

This paper is to present the performance data for pressure setting method using some tile bonds for application on the Ondol-Heating floor system. For this purpose, powder and liquid tile bonds(Organic.Inorganic mixed tile bonds) were compared with the conventional tile cement for pressure setting method in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion and heat ageing($70^{\circ}C$). Another experimental factors concerned tile bond properties such as mixing ratio(in case of using liquid admixture), open time, which are supposed to affect the tensile strength of tile, were studied and discussed through the experiments.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2001년도 학술논문발표회
• /
• pp.8-13
• /
• 2001

In recently, polishing tile(porcelain homogeneous polished tile) was used in the construction field as a finishing material. But, there happened some problems such as tile exfoliation by construction condition in early ages. Also, in the dry wall system which used to lightweight wall, for use of polishing tile on dry wall, the examination of adhesive stability of polishing tile is needed. In this Paper, adhesive strength of Polishing tile was investigated by tile bond types on gypsum board and non asbestos board coated by tar-urethane and polymer modified cementitious waterproofing membrane(Series I). Then, the effect of heat stress and vibration was estimated on gypsum and non asbestos board(Series II).

• 한국건축시공학회지
• /
• 제23권3호
• /
• pp.241-249
• /
• 2023

본 연구에서는 타일 하자 저감을 위해 시공 프로세스를 보완한 타일 모듈을 제작하였다. 타일 모듈은 떠붙임 시멘트 모르타르, 메쉬, 콘크리트로 구성되었다. 하자 발생 저감 가능성을 검토하기 위해 동결융해 시험 전후의 표면상태와 질량 변화율 실험을 실시하였으며 부착강도를 측정하였다. 그 결과, 알루미늄(A) 메쉬는 수중 환경에서, 강철(S) 메쉬는 기중 환경에서 열수축-팽창에 의한 하자가 상대적으로 다수 발생하였고, 메쉬의 크기가 작을수록 부착강도가 상승하는 경향을 보였다.

• 공업화학
• /
• 제10권3호
• /
• pp.486-490
• /
• 1999

타일을 부착시키는 tile 전용 cement mortar가 갖추어야 하는 물성인 우수한 보수성, 작업성, open time, 처짐저항성과 타임접착강도 등을 향상시키기 위해 본 연구에서는 mortar에 첨가하는 혼화제들의 홉합비율을 달리하였을 때 나타나는 특성을 비교 분석하였다. Mortar의 보수성 효과를 주는 hydroxypropylmethylcellulose에 소량의 합성 starch을 첨가해 줌으로써 mortar는 보수성을 유지하면서 겉마름이 적게되었고, open time이 길어져 작업성이 향상되었다. 타일의 접착강도를 높이기 위해 polyacrylamide와 ethylenevinyl acetate을 첨가하여 mortar 자체 및 타일의 처짐을 줄였고, 바탕면과 타일과의 mortar 접착력을 증대시켰다. 이와 함께 melment의 첨가로 mortar에 유동성을 주어 작업성을 향상시켰다. 이들 첨가제의 필요량은 cement량에 대해 hydroxypropyl methylcellulose는 0.80~1.20%, starch 0.10~0.15%, polyacrylamide 0.001~0.015%, ethylenevinyl acetate 0.05~0.10% 및 melment 0.003~0.005%의 혼합비율일 때 tile cement mortar의 물성이 향상됨을 알 수 있었다.