• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.173-178
• /
• 2005

The tile construction methods for existing have been used materials within limit which adhesion by wet method in masonry wall and concrete structure. These existing adhesive tech can caused many problems in construction of large and reform tile, after that it can be happened loose scale, peel off, falling off tile by heat and vibration or impact. In according to, this study is to test tile for bond stability, adhesive property by impact, vibration. low property by heat and then, we have the results as below; (1) The tile adhesive stability can be effected as adhesive area between bond agent and tile, adhesive area can more wide and press enough to ensure property. (2) Existing adhesive strength and standard relative tile construction is limited to adjust performance tile on the concrete and masonry wall. In summary, It is necessary to establish standard of performance and test method to ensure tile adhesive salability in dry wall.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.153-154
• /
• 2020

This study aims to find out the reason that tile adhesive(type III) for ceramic tile does not harden under some conditions especially high humidity even though long curing time. Bonding strength of adhesive between substrate and ceramic tile is evaluated depending on bonding conditions such as substrate kind(concrete, board), bonding material (tile adhesive, tile cement) and curing condition(humidity 50, 70%). Based on the results, this study aimed to establish the quality of tile adhesion strength under the relevant conditions.

• Journal of the Korea Institute of Building Construction
• /
• v.2 no.3
• /
• pp.163-170
• /
• 2002

Recently, polishing tile(porcelain homogeneous polished tile) was used in the construction field as a finishing material. But, there happened some problems such as tile exfoliation by construction condition in early ages. Also, for use of polishing tile in the dry wall system which used to lightweight wall, the examination of adhesive stability of polishing tile is needed. In this study, adhesive strength of Polishing tile was investigated by tile bond types on gypsum board and non asbestos board coated by tar-urethane and Polymer modified cementitious waterproofing membrane(Series I). Then, the effect of heat stress and vibration was estimated on gypsum and non asbestos board(Series II). As the result of study are the follows; (1) Polishing tile(600$\times$400mm) construction on waterproofing layer : Both laboratory estimation and spot examination sieve were happened that fall of tile because their hardening speed is late. (2) To using powder style adhesives in the dry wail with waterproofing layer : Adhesive strength of tile is Influenced by interface bond area and base side condition. (3) Shock and heat stresses : obvious decline of adhesive strength is not happened

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.06a
• /
• pp.128-129
• /
• 2020

In this study, flexural strength and tile adhesion strength were evaluated by using a mortar, dry mortar and an epoxy resin reinforced mortar to examine the adhesion performance by reinforcing the epoxy resin adhesive. As a result, it was clearly confirmed that the effect of improving the adhesion strength by reinforcing the epoxy resin adhesive regardless of the type of tile, and in particular, when applying the epoxy resin adhesive to the porcelain and polishing tiles, it is judged that sufficient adhesion performance can be secured.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.13-16
• /
• 2008

This paper is to present the performance data for improved direct setting method using tile bond for application of porcelain tile under 1 percent absorptance. For this purpose, improved direct setting method type 1 & 2(tile bond curing time 0, 24H) were compared with the conventional setting methods(including direct setting method and improved pressure setting method) in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion, heat ageing(70℃) and freeze-thaw cycle. On the basis of test results, the adhesive strength of direct setting method was lowest for the conventional setting methods. But improved direct setting method using tile bonds(A, B) came close to the result of improved pressure setting method using tile bonds.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.183-184
• /
• 2021

Defects such as falling and cracking of tiles installed in the bathrooms of apartment houses are frequently occurring. Therefore, in order to solve this problem, the A/S cost of construction companies and consumer complaints are increasing. The causes of tile defects include problems such as the selection of tile adhesive and lack of adhesive strength, the carelessness of the installer, the base surface, and the absorption rate of the tile. Therefore, in this study, an adhesive construction method using tile adhesives with high resistance to deformation of floors and tiles was studied. In addition, the properties and construction methods of tile adhesives were evaluated.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05c
• /
• pp.99-102
• /
• 2009

This paper is to present the performance data for pressure setting method using some tile bonds for application on the Ondol-Heating floor system. For this purpose, powder and liquid tile bonds(Organic.Inorganic mixed tile bonds) were compared with the conventional tile cement for pressure setting method in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion and heat ageing($70^{\circ}C$). Another experimental factors concerned tile bond properties such as mixing ratio(in case of using liquid admixture), open time, which are supposed to affect the tensile strength of tile, were studied and discussed through the experiments.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2001.11a
• /
• pp.8-13
• /
• 2001

In recently, polishing tile(porcelain homogeneous polished tile) was used in the construction field as a finishing material. But, there happened some problems such as tile exfoliation by construction condition in early ages. Also, in the dry wall system which used to lightweight wall, for use of polishing tile on dry wall, the examination of adhesive stability of polishing tile is needed. In this Paper, adhesive strength of Polishing tile was investigated by tile bond types on gypsum board and non asbestos board coated by tar-urethane and polymer modified cementitious waterproofing membrane(Series I). Then, the effect of heat stress and vibration was estimated on gypsum and non asbestos board(Series II).

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.3
• /
• pp.241-249
• /
• 2023

The objective of this research was to engineer a tile module that could efficiently curtail the incidence of tile defects during the construction phase. To assess the potential diminution in defect manifestation, we executed experiments centered on surface condition, the variation in mass before and after the freeze-thaw test, and adhesive strength. Our findings demonstrated that thermal contraction and expansion induced a relatively escalated frequency of defects in the underwater setting for the aluminum mesh, while the steel mesh saw a higher defect incidence in the air environment. Additionally, it was noted that the adhesive strength exhibited a trend towards augmentation as the mesh size dwindled. Collectively, these results suggest that the employment of smaller mesh sizes can foster improved adhesive strength, consequently diminishing tile defects. Further exploration and development of the tile module, informed by these insights, can substantially enhance the efficacy of the construction process.

• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.486-490
• /
• 1999

In this study, to improve the required properties of tile cement mortar such as excellent water retention capacity (WRC), workability, open time, sag resistance, and tile adhesive strength, tile cement mortars containing the several additives with different ratio were compared and analyzed. By adding small amount of synthesized starch to hydroxypropyl methylcellulose (HPMC) which is used for improving WRC, the decrease of moisture evacuation from mortar surface was observed and the workability of mortar was improved with long open time. Polyacrylamide (PAAm) and ethylencvinyl acetate (EVAc) were also added in order to increase the adhesion of tile. As a results, the saggings of mortar itself and tile were decreased and the adhesive strength of mortar between base and tile was enhanced. By adding melment, the workability was improved by increasing the fluidity of mortar. It is postulated that the properties of tile cement mortar was improved by adding 0.80~1.20% of HPMC, 0.10~0.15% of starch, 0.001~0.015% of PAAm, 0.05~0.10% of EVAc and 0.003~0.005% of melment to the cement mortar.