• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.813-824
• /
• 1988

Use of a plasma arc as the source of energy for penetration welding of thin plates gives rise to a cylindrical hole surrounded by the molten metal. Material moves from the front to the rear of the hole by flowing around the hole as the workpiece is translated relatively to the arc. Based on the finite difference method, three different computer models have been proposed for the steady state, two dimensional heat and mass flow during the plasma arc welding. In the formulation energy equation was derived by the energy blance method through the cell control volume, and all the governing equations derived for the fixed coordinates was translated for the moving coordinate system. The driving force for fluid flow being considered was only electromagnetic force. The calculated and measured molten poon and HAZ width were compared and better agreement was obtained for the models considering the keyhole effect.

• Laser Solutions
• /
• v.11 no.1
• /
• pp.25-31
• /
• 2008

The characteristics of femtosecond laser ablation of $Al_2O_3$ for prescision microfabrication are studied experimentally. Specifically, the process time during femtosecond laser drilling of microholes with $sub-100{\mu}m$ diameter are investigated for varying laser fluence, scan speed and beam path designs like trepanning with continuously changed start points. The accumulation of sub-micrometer size particles within the hole and the deterioration of edge clarity and roundness for decreasing hole diameter are examined and through process optimization the microdrilling with good hole quality is achieved using a femtosecond laser system (repetitionrate 1 kHz, wavelength 785 nm, pulse duration 185 fs)

• Journal of Korean Society for Quality Management
• /
• v.25 no.1
• /
• pp.135-141
• /
• 1997

The Copper-Clad Laminate (CCL) is a main electronic component of specialtype printed circuit boards (PCBs) such as Silver Through Hole PCB. This CCL should have high reliability under the aging test, and usually the test is done at a higher temperature (110-$150^{\circ}C$) than the normal. Then, this test condition of high temperature may cause such quality problems as hole eccentricity and reduction of distance between part holes. After measuring the CCL shrinkage affected by temperature, the correction factor of a press mold was a, pp.ied to solve these problems. The results showed that the tolerance of hole pitch(${\pm}$$100{\mu}m$) was satisfactory and the internal and external failure costs were reduced by 55%.

• Journal of the Korean Society of Visualization
• /
• v.9 no.3
• /
• pp.38-43
• /
• 2011

When draining takes place through an axially located drain port in a cylindrical tank without any prevent, a vortex with an air core occurs. In this study, semi spherical concave and convex meshes with different size inner hole are used to find the air core can suppress. The study is carried out with different values of inner hole of mesh and different install direction of semi spherical mesh using PIV and measured velocity distribution. By providing a mesh, the air core can be prevented, even if the ratio of inner hole of mesh and diameter of cylinder is around 0.66. The experimental results show that a convex mesh type is more effective to suppress the air core generation than a concave mesh type.

• Journal of Welding and Joining
• /
• v.27 no.4
• /
• pp.44-48
• /
• 2009

In automotive company, a lot of researchers have investigated for the spatterless welding process during last two decades. A spatter influences on the product quality such as strength and surface states. In this paper, a hollow tip is proposed for spatterless process. An optimal size of electrode hole is obtained from a weldability evaluation of each hole diameter. Through the cross section analysis, a phenomenon that molten metal moves in the hole which located between two workpiece is observed, and this makes spatterless welding process even though current is higher. Finally, widely acceptable weld area in lobe curve is obtained by using hollow tip as compare with conventional no hollow tip. In this paper, spatterless resistance spot welding with improvement weldability and productivity is proposed by using hollow tip.

• Journal of The Korean Astronomical Society
• /
• v.23 no.1
• /
• pp.63-70
• /
• 1990

The original axisymmetric, stationary electrodynamic model of the central engine in an active galactic nucleus proposed by Macdonald and Thorne consists of a supermassive black hole with magnetic field lines that pass through the region just outside the event horizon of the black hole. Each magnetic field line rotates with a constant angular velocity which will exceed the speed of light at large radii. Even though the field lines are purely mathematical entities this condition sets a stringent physical constraint on the motion of the magnetic field lines and the particles on them. In this paper we will show that we can remove this auxiliary constraint in our model by allowing nonstationary processes. As a result the magnetic field lines can be twisted and wound up in a region lying outside of the quasi-stationary magnetosphere of the black hole. We conclude that astrophysical jets are formed in that region due to the twisted and wound magnetic field lines powered by the Blandford-Znajek process and the other driving forces.

• Journal of the Korean Society of Safety
• /
• v.16 no.3
• /
• pp.89-98
• /
• 2001

There have been a lot of studies about repair & strengthening of the concrete structure. But there has almost not been my study on section damage effect due to holes drilled out for installing additional facilities or equipment, such as rack on the wall of building or underground culvert system, plumbing system through the column or wall of it, after being occupied. This study is to find out how much the section loss due to holes will give loss of section strength. We cm determine if we repair or reinforce it completely or not, using strength loss from the hole. Hole size of diameter 3cm, 2cm, lcm, depth of 3cm, 5cm, 10cm, and position of each hole has been considered as variables of this study. It is concluded that section loss 30% results in 53% of strength damage.

• Water Engineering Research
• /
• v.3 no.3
• /
• pp.155-162
• /
• 2002

This study presents the theoretical approach for volume concentration, velocity profile, and granular discharge on the fluid-granule mixed flow downstream of the scour hole at the outlet of the hydraulic structure. Concept of dilatant model was applied for the stress-strain relationships of fluid-granule mixed flow since the flow downstream of the scour hole corresponds to debris flow, where momentum transfers through particle collisions. Mathematical formulations were derived using momentum equation and stress-strain relation of the fluid-granule mixture. Velocity profile under the assumption of uniform concentration over flowing layer showed the downward convex type. Deposition angle of downstream hump was found to be a function of an upstream slope angle, a dynamic friction angle and a volume concentration irrespective of flow itself, Granular discharge and the overflow depth were obtained with given values of inflow rates. Experimental results showed relatively good agreements with theoretical ones.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.116-119
• /
• 1997

In this paper A double-layer organic electroluminescent(EL) device was fabricated using a TPD(N,N'-dipheny] -N,N'-bis(3-methylphenyl)-[1,1'-biphenyl]-4.4'-diamine: aromatic diamine), as a hole-transport material and tris (8-hydroxy quinolinate) aluminum(Alq$_3$) as a an emiting material and its performance characteristics were investigated. structure of devices is ITO/TPD/Alq$_3$/Al. we have fabricated hole transport layer of two types. Doping material of Hole Transport material is Poly(methyl methacrylate)(PMMA) and PEI(Poly-Ether-Imide). Carrier injection from the electrodes to the doped PMMA and PEI layer through the dopants and concomitant electroluminescence from Alq$_3$were observed. Green emission with luminance of 40cd/m$^2$was achieved at a drive voltage of 30V

• Journal of Korea Multimedia Society
• /
• v.12 no.12
• /
• pp.1745-1754
• /
• 2009

PTZ (Pan-Tilt-Zoom) camera based surveillance systems are enlarging their field of application due to their wide observable area. We aimed to detect both static and moving objects in automated working space by using a PTZ camera. For object detection we used background difference method because of the high quality segmentation. However, the method has a problem called 'hole' that is caused by non-continuous surveillance of the PTZ camera and its own characteristics. Moreover, the occlusion which occurs when the moving object overlaps with the static object should be solved for robust object detection. In this paper, we suggest a region-based technique for updating background images thereby overcoming the hole and occlusion problem. Through experiments with real scenes, it was verified that meaningful static and/or moving objects were detected very well.