• 대한조선학회논문집
• /
• 제59권3호
• /
• pp.173-182
• /
• 2022

The present study suggests a procedure of establishing a ship dynamics modeling by regression of free-running model test results. The hydrodynamic force and moment of the whole model ship is derived from the low-pass filtered acceleration in the turning circle and zigzag maneuver tests. Force and moment of the propeller and rudder are separated from that of the whole ship to acquire the hull force and moment terms, based on the principles of the component model. The low-pass filter frequency is verified in prior to dynamics modeling, to find the threshold frequency of 2.5 Hz. The dynamics modeling of the hull is compared with the component modeling by captive model tests. Because of strong correlation between sway velocity, yaw angular velocity, and heel angle, each maneuvering coefficient is not able to be validated, but the whole modeling shows good agreement with the captive model tests.

• 생태와환경
• /
• 제39권1호통권115호
• /
• pp.100-109
• /
• 2006

본 연구는 영양염이 풍부한 하수처리수를 이용한 인공수로에서 사상성 부착조류의 성장에 미치는 요인들(유속. 부착기질, 인 농도)을 평가하였다. 실험은 하수처리수를 이용한 현장 인공수로와 실내 순환수로에서 부착조류의 성장실험을 수행하였고, 서로 다른 인 농도에서의 사상성 부착조류 종간의 성장률과 인 흡수율을 비교하였다. 조절된 유속조건(5 ${\sim}$ 15 cm $s^{-1}$)에서 사상성 부착조류의 순생산성은 유속이 빠를수록 높았으나 최대의 순생산성은 10 cm $s^{-1}$ 유속에서 나타났다. 현장 인공수로와 실내순환수로 실험 간에 사상성부착조류의 최대성장은 기질에 따라 다르게 나타났다. 부유물질이 충분히 제거되지 않았던 현장 인공수로 실험에서는 망목이 20 mm인 철망에서, 실내순환수로 실험에서 사상성 부착조류의 성장은 자연섬유망에서 높게 나타났다. 0.05 ${\sim}$ l.0 mg P $L^{-1}$로 조절된 인 농도범위에서 3종의 사상성 부착조류 성장률은 인 농도가 높아짐에 따라 증가하였으나, 각 종들은 인 농도에서 따라 차별적인 성장을 나타냈다. 또한 영양염 농도가 매우 높은 환경에서 사상성 부착조류 생물량의 발달이 크면 클수록 높은 유속이 사상체의 탈리를 유발하여 조류의 성장을 감소시키는 제한요인으로 작용할 수 있음이 제시되었다. 탈리된 사상체는 연결된 하천, 저수지, 하류의 수질과 생태계를 악화시킬 수 있기 때문에 하천 수질관리에 있어 중요한 요인으로 고려한 필요성이 크다.

• 한국통신학회논문지
• /
• 제25권5B호
• /
• pp.871-878
• /
• 2000

이 논문은 저궤도 이동 위성 통신에서 나타나는 심각한 도플러 천이와 페이딩을 극복하면서 패킷 전송효율을 증가시킬 수 있는 DS/CDMA 시스템의 초기동기기법으로 분할 정합 여파기/참조 여파기 기법을 제안한다. 정합여파기의 정합구간을 분할하는 분할 정합여파기를 이용하여 극심한 도플러 천이를 극복하였으며, 참조여파기를 이용하여 시변하는 간섭과 페이딩에 강인한 초기동기를 이룰 수 있다. 성능분석의 척도로써 평균초기동기시간과 패킷 전송효율을 이용하며, 도플러 천이와 칩당 에너지대 잡음비, 사용자 이동속도, 음영 표준편차, 패킷 프리앰블내 심볼수 등과의 관계를 고찰한다.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2004년도 추계학술대회 논문집
• /
• pp.18-21
• /
• 2004

Lock-on characteristics of the flow around a circular cylinder performing a rotationally oscillation with a relatively high forcing frequency have been investigated experimentally using flow visualization and hot-wire measurements. Dominant parameters are Reynolds number (Re), amplitude of oscillation $(\theta_A)$, and frequency ratio $F_R=f_f\;/\;f_n$, where $f_f$ is the forcing frequency and if is the natural frequency of vortex shedding. Experiments were carried out under the conditions of $Re=4.14\times10^3,\;\pi/15\leq\theta_A\leq\pi/3$, and $F_R=1.0$. The effects of this active control technique on the lock-on flow regime of the cylinder wake were evaluated through wake velocity measurements and spectral analysis of hot-wire signals. The rotary oscillation modified the flow structure of near wake significantly. The lock-on phenomenon was found to occur in the range of frequency encompassing the natural vortex shedding frequency. In addition, when the amplitude of oscillation is less than a certain value, the lock-on phenomenon was occurred only at $F_R=1.0$. The lock-on range expanded and vortex formation length decreased as the amplitude of oscillation increases. The rotary oscillation generated small-scale vortex structure just near the cylinder surface.

• Coupled systems mechanics
• /
• 제7권4호
• /
• pp.407-420
• /
• 2018

In solid-liquid two phase flow, the knowledge of how descending solid particles affected by the presence of downstream wall is important. This work studies at what interstitial distance the velocity of a vertically descending sphere is affected by a downstream wall as a consequence of wall-modified hydrodynamic forces through a validated dynamic model. This interstitial distance-the hydrodynamic coupling distance ${\delta}_c-is$ found to decay monotonically with the approach Stokes number St which compares the particle inertia to viscous drag characterized by the quasi-steady Stokes' drag. The scaling relation ${\delta}_c-St-1$ decays monotonically as literature below the value of St equal to 10. However, the faster diminishing rate is found above the threshold value from St=10-40. Furthermore, an empirical relation of ${\delta}_c-St$ shows dependence on the drop height which clearly indicates the non-negligible effect of unsteady hydrodynamic force components, namely the added mass force and the history force. Finally, we attempt a fitting relation which embedded the particle acceleration effect in the dependence of fitting constants on the diameter-scaled drop height.

• 대한치과의사협회지
• /
• 제16권7호통권110호
• /
• pp.531-536
• /
• 1978

Adult cats were light anesthetized with ethyl ether and heart was removed fastly. cardiac papillary muscle was dissected from heart in organ bath con taining Tyrode solution saturated with 95% O₂+5% CO₂, and prepared papillary muscles were placed in Tyrode solution that was continuously circulated and gassed with 95% O₂+5% CO₂at 32℃. The isolated papillary muscle was stimulated continuously with platinum pin electrode at frequency of 15/min and 90/min by means of electric stimulator and transmembrane action potentials were recorded with microelectrdes on the oscilloscope. The drug used was d-propranolol and its concentration was 0.5, 1.5 and 5.0 mg/L. The results obtained were as follows: 1. D-propranolol increased the threshold voltage of papillary muscle and raised by average of 213.6% of control. 2. D-propranolol had no effect on duration of action potential. 3. Conduction time of isolated papillary muscle was increased by d-propranolol and its effect was prominent at frequency of 90/min. 4. the maximum upstroke velocity was decreased by d-propranolol and its effect was dose-depndent decrease.

• 한국자동차공학회논문집
• /
• 제11권2호
• /
• pp.148-156
• /
• 2003

Many car manufacturers have frequently adopted an aggressive inflator and a lower threshold speed for airbag deployment in order to meet an injury requirement for unbolted occupant at high speed crash test. Consequently, today's occupant safety restraint system has a weakness due to an airbag induced injury at low speed crash event. This paper proposes a new crash algorithm to improve the weakness by suppressing airbag deployment at low speed crash event in case of belted condition. The proposed algorithm consists of two major blocks-crash severity algorithm and deployment logic block. The first block decides crash severity with two levels by means of velocity and crash energy calculation from acceleration signal. The second block implemented by simple AND/OR logic combines the crash severity level and seat belt status information to generate firing commands for airbag and belt pretensioner. Furthermore, it can be extended to adopt additional sensor information from passenger presence detection sensor and safing sensor. A simulation using real crash data for a 1,800cc passenger vehicle has been conducted to verify the performance of proposed algorithm.

• 한국지형학회지
• /
• 제24권3호
• /
• pp.61-81
• /
• 2017

Traditional approaches to surface moisture problems in the context of aeolian research have focused on the initiation of sand movement, developing various models for predicting threshold velocity on a wet surface. They have been unsatisfactory, however, in explaining field observations because they have not incorporated spatiotemporal variability of surface moisture, the interactions between transported sand grains and surface, and the role of aeolian transport in controlling surface moisture. As Nield (2011) showed, a simplified numerical model can be used to investigate this issue. This research aims to explore the feedback structures between aeolian transport and surface moisture using a modified sand slab model. Key modifications are the introduction of simultaneous updating scheme for all the slabs and moisture-assigning procedures with and without aeolian transport. The major findings are as follows. Moist surface conditions suppress sand slab movement, leading to the development of smaller-scale topography. Available sands for aeolian transport are determined by the vertical patterns of moisture content with its variations from groundwater to the surface. Sand patches on a wet surface act as a localized source area. Sand movement drives immediate changes in surface moisture rather than time-lag reponses, mostly when moist conditions are dominant.

• Geomechanics and Engineering
• /
• 제16권5호
• /
• pp.483-493
• /
• 2018

Experimental study of the deterioration of high-temperature rock subjected to rapid cooling is essential for thermal engineering applications. To evaluate the influence of thermal shock on heated granite with different temperatures, laboratory tests were conducted to record the changes in the physical properties of granite specimens and the dynamic mechanical characteristics of granite after rapid cooling were experimentally investigated by using a split Hopkinson pressure bar (SHPB). The results indicate that there are threshold temperatures ($500-600^{\circ}C$) for variations in density, porosity, and P-wave velocity of granite with increasing treatment temperature. The stress-strain curves of $500-1000^{\circ}C$ show the brittle-plastic transition of tested granite specimens. It was also found that in the temperature range of $200-400^{\circ}C$, the through-cracks induced by rapid cooling have a decisive influence on the failure pattern of rock specimens under dynamic load. Moreover, the increase of crack density due to higher treatment temperature will result in the dilution of thermal shock effect for the rocks at temperatures above $500^{\circ}C$. Eventually, a fitting formula was established to relate the dynamic peak strength of pretreated granite to the crack density, which is the exponential function.

• Tribology and Lubricants
• /
• 제39권5호
• /
• pp.216-219
• /
• 2023

This study employs molecular dynamics simulations to investigate the material behavior of workpieces in waterjet machining processes. To gain fundamental insights into waterjet machining, simulations were conducted using pure water, excluding abrasive particles. The simulation model comprised thousands of water molecules interacting with a single crystal metal workpiece. Water molecule clusters were imparted with various velocities to initiate collisions with the metal workpiece. The material behavior of the metal surface was analyzed with respect to the applied velocity conditions, considering the intricate interplay between water molecules and the workpiece at the atomic scale. The results demonstrated that the machining of the metal workpiece occurred only when water molecules were endowed with velocities above a certain threshold. In cases where energy was insufficient, the metal workpiece exhibited a slight increase in surface roughness due to mild plastic deformation, without undergoing substantial material removal. When machining occurred, the ejection of material revealed a 3-fold symmetric pattern, confirming that material removal in waterjet machining of the metal workpiece is primarily driven by plastic deformation-induced material ejection. This research provides crucial insights into the mechanisms underlying waterjet machining and enhances our understanding of material behavior during the process. The findings can be valuable in optimizing waterjet machining techniques.