• 센서학회지
• /
• 제22권2호
• /
• pp.100-104
• /
• 2013

A superhydrophobic mesh is a unique structure that blocks water, while allowing gases, sound waves, and energy to pass through the holes in the mesh. This mesh is used in various devices, such as gas- and energy-permeable waterproof membranes for underwater sensors and electronic devices. However, it is difficult to fabricate micro- and nano-structures on three-dimensional surfaces, such as the cylindrical surface of a wire mesh. In this research, we successfully produced a superhydrophobic water-repellent mesh with a high contact angle (> $150^{\circ}$) for nanofibrous structures. Conducting polymer (CP) composite nanofibers were evenly coated on a stainless steel mesh surface, to create a superhydrophobic mesh with a pore size of $100{\mu}m$. The nanofiber structure could be controlled by the deposition time. As the deposition time increased, a high-density, hierarchical nanofiber structure was deposited on the mesh. The mesh surface was then coated with Teflon, to reduce the surface energy. The fabricated mesh had a static water contact angle of $163^{\circ}$, and a water-pressure resistance of 1.92 kPa.

• 천문학회보
• /
• 제36권2호
• /
• pp.107.1-107.1
• /
• 2011

Density Probability Distribution Functions (PDFs) are a classic statistical way to study properties of Interstellar Medium (ISM) turbulence. In our three-dimensional MHD simulations, density PDFs of the position-position velocity (PPV) spaces are close to a log-normal distribution. the PDF widths depend on the plasma parameters such as magnetic strength and sonic Mach number. Futhermore, we compare these simulations results to Galactic molecular clouds observed by Jackson et. al (2006). By fitting of the velocity dispersion in the spectral line observation, volume density PDFs of the defined molecular clouds indicate that the sound speeds of the turbulences seem to have a few times larger than the simulation results. In order to understand the inconsistency with general characteristics of turbulence, we consider other simulations inducing the turbulent flow randomly at small driving scales. We find that the density PDF width decreases at more smaller driving scale. Finally, the simulations suggest that sources of ISM turbulence in Galactic molecular clouds can be important on small scales.

• 소성∙가공
• /
• 제11권8호
• /
• pp.710-715
• /
• 2002

This paper describes the numerical determination of optimum blank diameter for sound material flow and high precise thread profile of a spindle screw through external thread rolling using two-three roll dies. Initial blank diameter affects the dimensional accuracy and surface finish qualities of a spindle screw in thread rolling process, therefore it is very important to determine the optimum blank diameter in thread rolling process. In order to determine the optimum blank diameter, this paper suggests the calculation method of initial bland diameter considering the real shape of tooth. The finite element code DEFORM is applied to analyze the metal flow of tooth, and these analytical results are verified by thread rolling experiment for spindle screw.

• 대한기계학회논문집
• /
• 제18권11호
• /
• pp.2805-2816
• /
• 1994

This paper describes dynamic finite element analyses performed to study the dynamic behaviors of a shipping container under the impact onto rigid target due to the accidental fall from the hight of 9 m. Using two and three dimensional techniques, the shipping container which gave the maximum damage, ten different drop orientations are considered ; at intervals of $5^{\circ}$ from $45^{\circ}$ to $90^{\circ}$ According to the present results, the orientation of the shipping container which gave the maximum damage is $85^{\circ}$ from horizontal for oblique drop in the primary impact. In the optimal design of the shipping container, the impact limiter material must be considered importantly because it's proper selection affects the weight and the manufacturing cost of the shipping container. The analysis of the shipping container in this paper demonstrated that the shipping container is structurally sound relative to the regulatory drop test requirements.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.256-257
• /
• 2006

3D printing of NiTi alloys has been successfully achieved. A novel printing process has been developed and used, which consists in selective deposition of a solvent on a granule bed. The granules are composed of metal powders and thermoplastic binder, which are mixed and sieved by conventional methods. A sound green strength is obtained after solvent evaporation. Sintered parts exhibit good density, proper phase composition and shape memory behaviour.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.252-253
• /
• 2006

The fabrication of complex-shaped parts out of Co-Cr-Mo alloy and 316L stainless steel by three-dimensional printing (3DP) was studied using two grades of each alloy with average particle size of 20 and $75\;{\mu}m$, respectively. To produce sound specimens, the proper 3DP processing parameters were determined. The sintering behavior of the powders was characterized by dilatometric analysis and by batch sintering in argon atmosphere at $1280^{\circ}$ for 2h. The 3DP process has successfully produced complex-shaped biomedical parts with total porosity of 12-25% and homogenous pore structure, which could be suitable for tissue growth into the pores.

• 한국군사과학기술학회지
• /
• 제9권2호
• /
• pp.26-33
• /
• 2006

A sonar dome is basically designed and installed to protect sonar array from shocks, sea wave slaps and floating matters. The acoustic wave passing through sonar dome, however, can be distorted in magnitude and phase. This paper presents a numerical method for predicting the steady-state sound pressure on the surface of transducer array in the sonar dome and typical results of sonar beam pattern affected by sonar dome. A beam tracing model with phase information and a multi-layered elastic boundary model are involved. A full three-dimensional sonar dome is modeled as a GRP acoustic window, a rubber coated steel baffle and a rubber coated steel hull. A transducer array is modeled as thick steel cylinder. There are some assumptions such as incidence of plane wave, specular reflection on boundary and directionality of transducer element.

• Restorative Dentistry and Endodontics
• /
• 제20권2호
• /
• pp.432-461
• /
• 1995

The basic principles in the design of Class II amalgam cavity preparations have been modified but not changed in essence over the last 90 years. The early essential principle was "extension for prevention". Most of the modifications have served to reduce the extent of preparation and, thus, increase the conservation of sound tooth structure. A more recent concept relating to conservative Class II cavity preparations involves elimination of occlusal preparation if no carious lesion exists in this area. To evaluate the ideal ClassII cavity preparation design, if carious lesion exists only in the interproximal area, three cavity design conditions were studied: Rodda's conventional cavity, simple proximal box cavity and proximal box cavity with retention grooves. In this study, MO amalgam cavity was prepared on maxillary first premolar. Three dimensional finite element models were made by serial photographic method. Linear, eight and six-nodal, isoparametric brick elements were used for the three dimensional finite element model. The periodontal ligament and alveolar bone surrounding the tooth were excluded in these models. Three types model(B option, Gap option and R option model) were developed. B option model was assumed perfect bonding between the restoration and cavty wall. Gap option model(Gap distance: $2{\mu}m$) was assumed the possibility of play at the interface simulated the lack of real bonding between the amalgam and cavity wall (enamel and dentin). R option model was assumed non-connection between the restoration and cavty wall. A load of 500N was applied vertically at the first node from the lingual slope of the buccal cusp tip. This study analysed the displacement, 1 and 2 direction normal stress and strain with FEM software ABAQUS Version 5.2 and hardware IRIS 4D/310 VGX Work-station. The results were as followed. 1. Rodda's cavity form model showed greater amount of displacement with other two models. 2. The stress and strain were increased on the distal marginal ridge and buccopulpal line angle in Rodda's cavity form model. 3. The stress and strain were increased on the central groove and a part of distal marginal ridge in simple proximal box model and proximal box model with retention grooves. 4. With Gap option, Rodda's cavity form model showed the greatest amount of the stress on distal marginal ridge followed by proximal box model with retention grooves and simple proximal box model in descending order. 5. With Gap option, simple proximal box model showed greater amount of stress on the central groove with proximal box model with retention grooves. 6. Retention grooves in the proximal box played the role of supporting the restorations opposing to loads.

• 한국음향학회지
• /
• 제21권8호
• /
• pp.708-718
• /
• 2002

본 연구에서는 진동-음향계에서 방사되어 생성된 일반 근접장에서 음향 인텐시티 기법을 이용해 소음원을 파악하는 방법의 문제점에 관하여 논한다. 이를 위해 자동차나중장비의 엔진실을 모사하는 3차원 구조물 모델을 고려한다. 실제 상황과 유사하도록 모델에는 음원들이 복잡한 형상의 표면에 상호 연관성이 있는 또는 없는 형태로 분포한다. 즉, 음원들은 음향학적으로 단단한 상자들에 의해 형성된 좁은 공간으로 연결되어 있다. 따라서 반사가 심한 음장에 면한 표면에 배치되어 있으며, 전체 구조의 바닥 부분은 하부의 바닥과 작은 틈새만큼 떨어져 있다. 음향 경계요소법을 이용하여 근접 음장과 내부 음장의 인텐시티를 계산한다. 주어진 음원들간의 상대적 위상, 주파수, 위치에 따른 효과를 조사하였고, 그 결과를 등인텐시티선도, 벡터도 및 에너지 유선으로 표현하였다. 현장에서 종종 행해지는 바와 같이, 예를들어 엔진룸 상부에서 인텐시티를 측정하여 음원을 조사하는 것과 같은, 반사장이 강한 음장에서 음향 인텐시티 기법을 적용하여 음원탐색을 시도할 경우 가짜 음원이 검색될 수 있음을 보였다. 이와 같은 음장에서 정확한 결과를 얻기 위해서는, 음원탐색 수행 전에 음장의 리액티비티에 대한 조사가 먼저 필요하며, 측정을 시행하기 전에 음장의 리액티비티를 없애거나 대폭적으로 줄이는 작업이 선행되어야 할 것이다.

• 한국소음진동공학회논문집
• /
• 제21권1호
• /
• pp.81-88
• /
• 2011

The method is introduced for estimating the noise source contribution on the noise of PDP TV in a multiple-input system where the input sources may be coherent with each other. By the coherence function method, it is found that the biggest part of the noise source in the PDP TV noise is generated by the PCB boards which consume high power and produce high heat. This analysis is modeled as three-input/single-output system because the noise is generated by three main boards, X-board, Y-board, SMPS that are located close to each other. The coherence function method is proved to be useful tool for identifying of noise source. In this study, Transfer Path Analysis using MDSA is implemented to determine the quantitative noise contribution of each board for PDP TV with the rear case closed and with the rear case open. And the possibility of noise reduction is confirmed through the experimental method that isolates the most contributing board by adding sound-absorbing materials to it.