• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.4
• /
• pp.288-297
• /
• 2009

A serpentine channel geometry often used in a fuel cell has a strong pressure gradient between adjacent channels in specific regions. The pressure gradient helps some amount of reactant gas penetrate through a gas diffusion layer(GDL). As a result, the overall serpentine flow structure is slightly different from the intention of a designer. The purpose of this paper is to examine the effect of serpentine flow structure on current density distribution. By using a commercial code, STAR-CD, a numerical simulation is performed to analyze the fuel cell with high aspect ratio of active area. To increase the accuracy of the numerical simulation, GDL permeabilities are measured with various compressive forces. Three-dimensional flow field and current density distribution are calculated. For the verification of the numerical simulation results, water condensation process in the cathode channel is observed through a transparent bipolar plate. The result of this study shows that the region of relatively low current density corresponds that of dropwise condensation in cathode channels.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.2
• /
• pp.22-28
• /
• 1999

Small amplitude in-phase oscillations of multi-cylinders are considered both numerically and experimentally. Flow field is separated into inner and outer regions. The basic unsteady solution is obtained analytically and the secondary flow, termed as steady streaming flow, can be obtained numerically by using Finite Volume Code with Panel Method. The Particle Induced Velocimetry, one of whole field measurements, is introduced for comparison with numerical flow visualization quantitatively. Among the algorithms for PIV, the Three Step Vector Searching Technique is applied to reduce CPU time. Small but non-zero damping coefficient, that is important in lightly damped system can be obtained with varying number of bodies and distances.

• Journal of Korean Society of Rural Planning
• /
• v.21 no.4
• /
• pp.139-155
• /
• 2015

This study was conducted to effectively develop rural tourism in Korea. For the purpose, tourism that can develop with local industries and cultures together was designated as life-type tourism and development models of such tourism were reviewed based on an understanding that province-oriented tourism is necessary. An analysis of three actual cases of Japan led to following results. First, life-type tourist destinations can be developed in connection with making local areas based on their special themes, can be developed in relation to their life cultures based on their peculiar life cultures and can be developed in creative forms using characteristic environment and organizational culture of those areas. In pursuing life-type tourist attractions, it will be possible to make practical development using it with those three basic models. Second, it is important to form a flow covering the entire regions based on their own special themes, to build cyclical structure of regions and tourism and tourism and industries and to create overall conditions that can help local residents get benefits and join together, in order to develop such life-type tourist destinations. Development of life-type resort tourist destinations needs roles of practical organizations that can effectively manage them, but such organizations should be dynamic and should be distant from management of money as much as possible.

• Structural Engineering and Mechanics
• /
• v.63 no.4
• /
• pp.567-574
• /
• 2017

Sedimentation tanks are essential structures to filter the suspended sediments in the inlet flow which are constructed at the inlet of the basins forked from rivers and irrigation canals. The larger the constructed tank, the better the sedimentation process is conducted. However, the construction and dredging costs increase. In this regard, improving the performance and sedimentation efficiency seem necessary by alternative methods. One of these effective methods is using baffle plates. Most of the studies carried out in this field are on the use of these baffles in the primary and secondary sedimentation tanks. Hence, this study is carrier out with the objective of increasing the retention efficiency in the irrigation sedimentation tanks using baffles. To reach this goal, the experiments were carried out in a flume with length 8 meters, width 0.3 meters, and height 0.5 meters, considering a sedimentation tanks with a length of 3 meters, in three different inlet concentration, three flow rates and three Froude numbers. The baffles were mounted at the bottom of the tank and the effects of the angle, height and position in the tanks were investigated. The results showed that on average, employing the baffles increased the sedimentation efficiency 5 to 6% and the highest value was obtained for angle 60 with respect to the flow direction. According to the results of this study, the most favorable height and position of these baffles were obtained to be in 40% of the depth of the flow and 50% of the length of the sedimentation tank, respectively. Also, by increasing the number of baffles, the sedimentation efficiency decreased. Regarding the sedimentation regions in this case, more than 80% of the settled sediments were observed in the middle of the tank measured from the inlet.

• Wind and Structures
• /
• v.37 no.1
• /
• pp.25-38
• /
• 2023

Due to the complexity and difficulty in meeting the multiphase flow complexity, similarity, and multiscale characteristics, the mechanism of snow drift is so complicated that the snow deposition prediction is still inaccurate and needs to be far improved. Meanwhile, the validation of prediction methods is also limited due to a lack of field-measured data about snow deposition. To this end, a field measurement activity about snow deposition around a cube with time was carried out, and the snow accumulation process was measured under blowing snow conditions in northwest China. The maximum snow depth, snow profile, and variation in snow depth around the cube were discussed and analyzed. The measured results indicated three stages of snow accumulation around the cube. First, snow is deposited in windward, lateral and leeward regions, and then the snow depth in windward and lateral regions increases. Secondly, when the snow in the windward region reaches its maximum, the downwash flow erodes the snow against the front wall. Meanwhile, snow range and depth in lateral regions have a significant increase. Thirdly, a narrow road in the leeward region is formed with the increase in snow range and depth, which results in higher wind speed and reforming snow deposition there. The field measurement study in this paper not only furthers understanding of the snow accumulation process instead of final deposition under complex conditions but also provides an important benchmark for validating prediction methods.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.191-194
• /
• 2003

In this study, permeability tensor is computed for a three dimensional braided preform by applying a FVM to a unit cell. It is evident that resin will flow through the inter-tow and the intra-tow regions when pressure gradient is applied to the resin. The intra-tow region in the braided preform is regarded as not only an impermeable solid but also a permeable porous media. When the intra-tow region is excluded from domain of flow analysis in the case of the impermeable solid, the Stokes equation is computer for only inter-tow region. (omitted)

• Journal of Ocean Engineering and Technology
• /
• v.20 no.5 s.72
• /
• pp.23-29
• /
• 2006

A quasi depth-varying mathematical model for wind-generated circulation in coastal areas, expressed in terms of the depth-averaged horizontal velocity components and free surface elevation was validated and used to understand the diurnal circulation process. The wind velocity is considered as a dominant factor for driving the current. In this paper, three-dimensional numerical experiments that included the land topography were used to investigate the mesoscale air flaw over the coastal regions. The surface temperature of the inland area was determined through a surface heat budget consideration with the inclusion of a layer of vegetation.A series of numerical experiments were then carried out to investigate the diurnal response of the air flaw and wind-generated circulation to various types of surface inhomogeneities.

• Ocean Systems Engineering
• /
• v.7 no.3
• /
• pp.195-223
• /
• 2017

This paper presents 3D numerical simulations of a Free Standing Hybrid Riser under Vortex Induced Vibration, with prescribed motion on the top to replace the motion of the buoyancy can. The model is calculated using a fully implicit discretization scheme. The flow field around the riser is computed by solving the Navier-Stokes equations numerically. The fluid domain is discretized using the overset grid approach. Grid points in near-wall regions of riser are of high resolution, while far field flow is in relatively coarse grid. Fluid-structure interaction is accomplished by communication between fluid solver and riser motion solver. Simulation is based on previous experimental data. Two cases are studied with different current speeds, where the motion of the buoyancy can is approximated to a 'banana' shape. A fully three-dimensional CFD approach for VIV simulation for a top side moving Riser has been presented. This paper also presents a simulation of a riser connected to a platform under harmonic regular waves.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.1
• /
• pp.60-66
• /
• 2009

This study presents an experimental investigation of the shallow water impact of a box type structure. The analysis was done based on the video images captured by a high speed camera, the flow field obtained by PIV (Particle Image Velocimetry), and pressure measurements in the divided region. The video images showed quite good agreement with the description given by Korobkin. The PIV measurements of the velocity field provided a clear view of the flow pattern for all three stages. The pressure was measured at the bottom of the tank with strain gauge type pressure gauges. The pressure measurements showed the characteristics of divided regions.

• Journal of Mechanical Science and Technology
• /
• v.20 no.6
• /
• pp.905-913
• /
• 2006

The instability curve of a Rijke tube system was obtained accurately by following different paths of heat power and flow-rate for three regions and by defining its locus from the criterion based on the measured sound pressure levels. The unstable limits in the region of flow-rate lower than that at the minimal power are compared with previous data. To observe the effect of turbulence on the unstable limits, inflow turbulence was introduced by placing a bundle of circular cylinders upstream of the heating part ($50). The large-amplitude inflow fluctuation may delay the transition of the chamber acoustic mode to the unstable Bone even at a sufficient power.