• Current Photovoltaic Research
• /
• v.1 no.1
• /
• pp.59-62
• /
• 2013

We investigated the effects of ZnO thin film deposition methods on the performance of inverted polymer solar cells with a structure of ITO/ZnO/P3HT:PCBM/MoO3/Al. The ZnO thin films were deposited by various methods (spin coating of nanoparticles, sol-gel process, atomic layer deposition) and their morphology was analyzed by atomic force microscopy (AFM). The device with ZnO nanoparticle thin films showed the highest power conversion efficiency of 3 % with low series resistance and high shunt resistance. The superior performance of the device with the ZnO nanoparticle layer is attributed to better electron extraction capability.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.04a
• /
• pp.121-121
• /
• 2000

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.537-539
• /
• 2009

We report the improvement in adhesion of IZO thin films through oxygen ($O_2$) plasma treatment of organic polymer film. In conclusion, the $O_2$ plasma treatment of an organic polymer film was accomplished with improving ca. 1.8 times in adhesion than that of the only general etch treatment on the same organic polymer film.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.91-94
• /
• 2003

The purpose of this project is to research and development of thin film supercapacitor with conducting polymer composite electrodes and polymer electrolyte which have high energy density for thin film supercapacitor. We investigated cyclic voltammetry and charge/discharge cycling of PFPT-flyash electrodes. The first discharge capacity of PFPT-flyash electrode with 40wt.% flyash was 24F/g, while that of PFPT-VOflyash electrode with 40wt.% VOflyash was 32F/g. The capacitance of PFPT-VOflyash composite film with polymer electrolyte was 32 F/g at 1st and 20th cycle, respectively. The capacitance of PFPT-VOflyash/Li cell with 40 wt% VOflyash was 141 F/g at 8th cycle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.12
• /
• pp.1009-1013
• /
• 2009

In this study, we have been synthesized the dielectric layer using pure organic and organic-inorganic hybrid precursor on flexible substrate for improving of the organic thin film transistors (OTFTs) and, design and fabrication of organic thin-film transistors (OTFTs) using small-molecule organic semiconductors with pentacene as the active layer with record device performance. In this work OTFT test structures fabricated on polymerized substrates were utilized to provide a convenient substrate, gate contact, and gate insulator for the processing and characterization of organic materials and their transistors. By an adhesion development between gate metal and PI substrate, a PI film was treated using $O_2$ and $N_2$ gas. The best peel strength of PI film is 109.07 gf/mm. Also, we have studied the electric characteristics of pentacene field-effect transistors with the polymer gate-dielectrics such as cyclohexane and hybrid (cyclohexane+TEOS). The transistors with cyclohexane gate-dielectric has higher field-effect mobility, $\mu_{FET}=0.84\;cm^2/v_s$, and smaller threshold voltage, $V_T=-6.8\;V$, compared with the transistor with hybrid gate-dielectric.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.4
• /
• pp.625-632
• /
• 2012

Optimization of process parameters in polymer extrusion is an important task to reduce manufacturing cost. To determine the optimum values of the process parameters, it is essential to find their influence on the strength of polymer breathable thin film. The significance of six important process parameters namely, extruder cylinder temperature, extruder speed, extruder dies temperature, cooling roll temperature, stretching ratio, stretching roll temperature on breathable film strength of polymer extrusion was determined. Moreover, this paper presents the application of Taguchi method and analysis of variance (ANOVA) for maximization of the breathable film strength influenced by extrusion parameters. The optimum parameter combination of extrusion process was obtained by using the analysis of signal-to-noise ratio. The conclusion revealed that extruder speed and stretching ratio were the most influential factor on the film strength, respectively. The best results of film strength were obtained at higher extruder speed and stretching ratio.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.84-87
• /
• 2020

The properties of ultra-thin two-dimensional (2D) organic ferroelectric Langmuir-Blodgett (LB) films of the poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] were investigated to find possible applicability in flexible and wearable electronics applications. In the C-V characteristics of the MFM capacitor of 2-monolayer of 5 nm films, a butterfly hysteresis curve due to the ferroelectricity of P(VDF-TrFE) was confirmed. Typical residual polarization value was measured at 2μC/㎠. When the MFM capacitor with ultra-thin ferroelectric film was measured by applying a 10 Hz bipolar pulse, it was shown that 65% of the initial polarization value in 105 cycles deteriorated the polarization. The leakage current density of the 2-monolayer film was maintained at about 5 × 10-8 A/㎠ for the case at a 5MV/cm electric field. The resistivity of the 2-monolayer film in the case at an electric field at 5 MV/cm was more than 2.35 × 1013 Ω·cm.

• International Journal of Internet, Broadcasting and Communication
• /
• v.6 no.1
• /
• pp.13-15
• /
• 2014

We develop a method to fabricate a flexible thin film audio systems using polyvinylidene fluoride(PVDF). The system we designed showed the properties of increased flexibility, transparency, and sound pressure levels. As an input port of two terminals, transparent oxide thin film with a low resistivity is adopted. In order to provide dielectric insulation, a transparent insulating oxide thin film is coated to obtain double-layered structure. In the range of visible light, the output from the output of the system showed a increased and improved sound pressure level. The piezoelectric polymer film of PVDF is used to produce mechanical vibration due to the applied electrical voltage signal. An analog electric voltage signal is transformed into sound waves in the audio system.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1568-1570
• /
• 2003

We have studied the I-V characteristics of polytetrafluoroethylene(PTFE) thin film depending on a variation of thickness. Polymer PTFE buffer layer was made using thermal evaporation technique. The device was made in the structure of ITO/PTFE/Al. We have observed the NDR(negative differential resistance) behavior between 2.5V and 5V. There are some reports on this NDR behavior in the polymer thin film[1]. We have studied the NDR behavior depending on a variation thickness. As the film thickness increased, The NDR behavior decreased and moved in low electrical field, and we have studied the conduction mechanism of PTFE thin film.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.11
• /
• pp.1945-1950
• /
• 2007

Two fluorene-based conjugated copolymers containing hexyl-thiophene derivatives, PF-1T and PF-4T, were synthesized via the palladium-catalyzed Suzuki coupling reaction. The number-average molecular weights (Mn) of PF-1T and PF-4T were found to be 19,100 and 13,200, respectively. These polymers were soluble in common organic solvents such as chloroform, chlorobenzene, toluene, etc. The UV-vis absorption maximum peaks of PF-1T and PF-4T in the film state were found to be 410 nm and 431 nm, respectively. Electrochemical characterization revealed that these polymers have low highest occupied molecular orbital (HOMO) levels, indicating good resistance against oxidative doping. Thin film transistor devices were fabricated using the top contact geometry. PF-1T showed much better thin-film transistor performance than PF-4T. A thin film of PF- 1T gave a saturation mobility of 0.001-0.003 cm2 V?1 s?1, an on/off ratio of 1.0 × 105, and a small threshold voltage of ?8.3 V. To support TFT performance, we carried out DSC, AFM, and XRD measurements.