• 한국생산제조학회지
• /
• 제26권4호
• /
• pp.378-386
• /
• 2017

Friction stir welding was performed using six welding conditions to evaluate the mechanical properties and microstructure of the welded zone based on its temperature change in the extruded plate of magnesium alloy AZ61. The welded zone temperature was measured using a thermocouple, and the maximum temperature ranges for the advancing and retreating sides were approximately $210-315^{\circ}C$ and $254-339^{\circ}C$, respectively. Depending on the welding conditions, a temperature difference of more than $100^{\circ}C$ was observed. In addition, the maximum yield strength and maximum tensile strength of the welded component was 84.4% and 96.9%, respectively, of those of the base material. For the temperatures exceeding $300^{\circ}C$, oxidation defects occurred in the weld zone, which decreased the mechanical strength of the weld zone. The microstructure and texture confirmed that fracture occurred because of the grain size deviation of the welding tool and the severe anisotropy of the texture of the welded joints.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.425-428
• /
• 2006

Recently, Direct Methanol Fuel Cell (DMFC) for portable devices has been received much attention because DMFC has a possibility of higher energy density than electrical batteries and smaller size than other fuel cells. This paper presents the fabrication and test of a thermopneumatic microactuator with a phase change for DMFC. A microactuator consists of an inlet an outlet a chamber, a heater and a sensor of resistance temperature detector(RTD). The micoractuator is fabricated by the spin-coating process, the lithograph process, the deep RIE process and so on. The total size of microactuator is $20{\times}20{\times}0.53mm^3$. When the current is applied, the heater heats liquid in chamber. As a result the liquid vaporizes. The response of temperature in the chamber was measured using thermocouple The changed temperature is $3^{\circ}C$ for 5 sec at 0.032W.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2000년도 제21회 KOSCO SYMPOSIUM 논문집
• /
• pp.168-174
• /
• 2000

A diode laser sensor system based on absorption spectroscopy techniques has been developed to measure $CO_2$ concentration and temperature non-intrusively in high temperature combustion environments using a 2.0 ${\mu}m$ DFB(Distributed Feedback) laser. Two optics was fabricated in pig-tail fashion and all optical components were implemented in a single box. The evolution of measurement sensitivity was done using test cell by changing sweep frequency and $CO_2$ concentration. Gas temperature was determined from the ratio of integrated line strengths. Species concentration was determined from the integrated line intensity and the measured temperature. The result show that the system has 2% error in wide operation frequency range and accuracy of $CO_2$ concentration was about 3%. The system was applied to measure temperature and concentration in the combustion region of a premixed $CH_4$ +air triangular flame. The measurement results of gas temperature agreed well with thermocouple results. Many considerations were taken into account to reduce optical noise, etalon effect, beam steering and base line matching problem. The evaluations results and actual combustion measurement demonstrate the practical and applicability for in-situ and real time combustion monitoring in a practical system.

• 오토저널
• /
• 제14권2호
• /
• pp.34-43
• /
• 1992

The purpose of this study is to consider the performance and exhaust characteristics in the practical engine according to the cooling water temperature change of engine and to set up the optimum cooling condition and to obtain the optimum operating condition of thermostat in the cooling system. In order to accomplish the purpose of this study, authors have used the following procedure. 1. This study is to investigate the influence of the cooling water temperature on the engine performance and the exhaust gas, authors regulated the cooling water temperature by using the special closing circuit and measured the concentration of exhaust gas by using the exhaust gas measuring system in the exhaust pipe. 2. This study carried out the experiment by regulating the opening degree of throttle valve and engine speed in the dynamometer and by changing the cooling water temperature, at the same time kept air-fuel ratio constant and made the spark ignition time MBT(Minimum spark advance for Best Torque) 3. This study measured the cooling water temperature by using the K-type thermocouple centring around the easy over-heated parts and by installing a special closing circuit. Therefore, in this study, authors intend to examine the influence of the cooling water temperature on the engine performance, exhaust gas and present the basic materials needed in the engine design including the optimum operating time control system for the cooling water temperature.

• 한국산학기술학회논문지
• /
• 제10권10호
• /
• pp.2572-2576
• /
• 2009

반도체 양산공정에 사용되는 웨이퍼 프로버의 척은 고온이건 저온이건 항상 일정한 온도균일도가 요구된다. 저온으로 운전 시에 온도분포를 써모커플을 이용하여 측정한 결과 온도균일도를 향상할 필요가 있음을 발견하였다. FLUENT를 이용한 전산해석을 하여 온도분포를 해석하였으며, 이 결과를 이용하여 냉각수 회로 배치의 변경과 국부적인 회로 폭의 확대 등 개선안을 제시하였다. 제시된 개선안과 현재 척의 온도분포를 비교한 결과 온도균일도가 향상되었음을 확인하였다.

• 조명전기설비학회논문지
• /
• 제21권7호
• /
• pp.54-60
• /
• 2007

15개의 광섬유 격자를 이용하여 전력설비의 온도변화를 상시 감시하는 분배형 광섬유 온도센서 시스템을 제작하였다. MEMS 파장가변 필터를 사용하는 복조시스템의 비선형 동작특성에 의한 측정오차를 보상하기 위하여 Fabry-Perot ITU 필터의 투과파장을 기준으로 하는 다항식 피팅 알고리즘을 사용하였다. 실험을 통하여 보상알고리즘이 구동주파수와 무관하게 센서시스템의 정밀도를 유지하는 것을 확인하였으며 기준 온도계로 사용한 써모커플과의 선형화 오차는 약 0.18[%]로 측정되었다.

• 항공우주시스템공학회지
• /
• 제2권4호
• /
• pp.7-12
• /
• 2008

Averaged heat transfer coefficients were measured in a turbine blade internal cooling passage model with three blockage walls. Each blockage wall was equipped with 9 staggered holes or slots in order to create different shaper of repeated jet impingement. The effect of jet shape on the averaged heat transfer coefficient was studied by the copper-thermocouple method and three Reynolds number of 10,000, 20,000, and 30,000 were tested. Results showed that the repeated stagger jets could increase the averaged heat transfer coefficient by at least 9 times compared to the smooth channel cases. Due to the large pressure drop induced by the repeated jet impingement, the thermal performance was less than 1 for all cases and decreased as the Reynolds number increased. Among the tested cases, the widest slot showed the best thermal performance. The measurement results showed that the thermal performance of the heat transfer augmentation by repeated stagger jets could be improved by altering the jet shape, and other shape of impingement jet will be studied in near future.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 추계학술발표대회 논문집
• /
• pp.190-195
• /
• 2008

The objective of this research is to determine overall heat transfer coefficients (K-value) of exterior wall, floor, and roof of Nakseonjae, a Korean traditional residence via field measurement of transient heat flow and temperature difference across each envelope component. Heat flow sensors and T-type thermocouple were attached on the internal and the external surface of each building component, and real-time measurement data were collected for the three consecutive summer days. The K-values determined in this research showed good agreement with other results from open literature. Peak and annual thermal loads of the traditional residence estimated by a commercial energy simulation program were compared with those for a current apartment house. The traditional house showed lower annual cooling load than that of the current building. It may caused by the fact that the traditional building has less air-tight envelopes and no fenestration passing direct solar radiation into the space.

• Tribology and Lubricants
• /
• 제9권1호
• /
• pp.62-69
• /
• 1993

Friction and wear behavior of a carbon/carbon composite material for aircraft brake material was experimentally investigated. Friction and wear test setup was designed and built for the experiment. Friction and wear tests were conducted under various sliding conditions. Friction coefficients were measured and processed by a data acquisition system and amount of wear measured by a balance. Stainless steel disk was used as the counterface material. Temperature was also measured by inserting thermocouple 2.5 mm beneath the sliding surface of the carbon/carbon composite specimen. Wear surfaces were observed by SEM, and analyzed by EDAX. The experimental results showed that sliding speed and normal force did not have significant effects on friction coefficient and wear factor of the composite. Temperature increase just below the surface was not large enough to cause any thermal degradation or oxidation which occurred at higher temperature when tested by TGA. Wear film was generated both on the specimen and on the counterface at relatively low sliding speed but cracks, grooves, and wear debris were observed at high sliding speed. Friction coefficient remained almost constant when the sliding speed or normal load was varied. It is believed that the adhesive and abrasive components contributed mainly to the friction coefficient. Wear behavior at low sliding speed was governed by wear film formation and adhesive wear mechanism. At high speed, fiber orientation, ploughing by counterface asperities, and fiber breakage dominated wear of the carbon/carbon composite.

• 한국공간구조학회:학술대회논문집
• /
• 한국공간구조학회 2008년도 춘계 학술발표회 논문집
• /
• pp.179-183
• /
• 2008

콘크리트에서의 손상 검증법은 비파괴 시험법을 주로 이용한다. 이러한 비파괴시험법은 다양한 센서를 이용하지만, 대부분의 손상을 검사하는 방법은 육안으로 확인한다. 비파괴 시험법에서 가속도계를 이용하여 철근 콘크리트 부재 내부의 불규칙한 균열 손상을 측정하기에는 철근의 방향성과 경계조건으로 어려움이 많다. 본 연구에서는 3축 가속도센서를 이용하고 탄성파를 가진하여, 콘크리트 부재 내부에 철근의 배치방향에 따른 영향 검토와 강도가 저하된 부재의 손상을 검토하기 위한 기초적 연구이다.