• Resources Recycling
• /
• v.17 no.3
• /
• pp.35-41
• /
• 2008

The study of coking technology to upgrade oil sand bitumen which is considered as alternative fuel was performed by using thermogravity analyzer and delayed coking reactor(600ml). To analyzed and compared coking characteristics of oil sand bitumen, the reactivities of oil sand bitumen were measured in the TGA. At the temperature conditions of $400{\sim}550^{\circ}C$ and the temperature rising velocity of $50^{\circ}C/min$. the termination time of coking reaction and conversion efficiencies increased with an increase of bed temperature. However the increase rate decreased over $450^{\circ}C$. So the coking reaction with oil sand bitumen might be over $450^{\circ}C$. Also the termination time decreased with increasing the temperature rising velocity. But the content of coke increased with increasing temperature rising velocity. At the experiments in the delayed coker, the temperature condition at maximum oil yield was $475^{\circ}C$ and the fuel properties of oil from coking reaction was almost equal with conventional diesel. It was verified that the coking process might be useful process to upgrade the oil sand bitumem by using API and SIMDAS.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.1
• /
• pp.75-81
• /
• 2007

Steam reforming of methane using Xe-arc solar simulator was studied for the application of concentrated solar energy into chemical reaction. The reactor, a volumetric absorber, consisted of a porous ceramic foam disk coated with commercial reforming catalyst. Operating temperature was in the range of $450\;-\;550^{\circ}C$ and the excess steam ratio to methane was from 3.0 to 5.0. At the steady-state condition, the conversion of methane Increased with temperature in the range of 15 % - 30 % and the experimentally determined conversion was found to be close to theoretical equilibrium conversion. It was also found that the CO selectivity slightly decreased with excess steam ratio. Finally, the conversion of methane decreased significantly with space velocity of reactants.

• Korean Chemical Engineering Research
• /
• v.61 no.1
• /
• pp.8-18
• /
• 2023

Increasing of energy demand due to the rapid growth of global population and the development of world economy has inevitably resulted in the continuously increase of fossil fuel usage in the world. However, highly dependence on fossil fuels has necessarily brought about critical environmental issues and challenges such as severe air pollutions and rapid global warming. In order to settle these environmental and energy problems, clean energy generations in the conventional combustion processes have widely adapted in the world. In particular, novel thermochemical conversion processes such as pyrolysis and gasification have rapidly been applied for generating clean energy. Fluidized bed technologies having advantages such as various fuel use, easy continuous operation, high heat and material transfer, isothermal operation, and lower operation temperature are widely adopted and used because they are suitable for thermochemical energy conversion. The latest research trends and important findings in the thermo-chemical conversion process with fluidized bed technologies are summarized in this review. Also, the need for research such as layered materials and substances to reduce fine dust (biomass, natural resource waste, etc.) was suggested. Through this, it is intended to increase interest and understanding in fluidized bed technology and to present directions for solving future challenges in fluidized bed process technology development.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.4
• /
• pp.305-312
• /
• 2008

ZnO/Zn redox cycle is the one of the promising thermochemical cycles for hydrogen production via water splitting with high temperature heat source like a concentrated solar energy. This paper reports the particle size effect of Zinc on water splitting behavior. Water splitting reaction experiments were carried out at isothermal conditions of 350 and 400$^{\circ}C$ in TGA (Thermo Gravimetric Analyzer) using four commercial Zinc powders (nano, <10 ${\mu}m$, <150 ${\mu}m$ and $150{\sim}600\;{\mu}m$ particle sizes). Before the experiments, average particle size of Zinc powders was analyzed by PSA (Particle Size Analysis). After the experiments, XRD (X-Ray Diffraction) and SEM (Scanning Electron Microscope) analyses were conducted on the samples. The experimental results showed that particle size had a effect on the conversion of Zinc to ZnO. Zinc conversion was increased, as the particle size decreased. Especially, the nano size particles were aggregated and the particle's morphology changed on the surface during hydrolysis reaction.

• Journal of Soil and Groundwater Environment
• /
• v.27 no.1
• /
• pp.17-24
• /
• 2022

This work examined the effect of mixing transition metal-based additives [FeCl₃, Fe-containing paper mill sludge (PMS), CoCl₂·H₂O, ZrO₂, and α-Fe₂O₃] on the thermochemical conversion of coffee waste (CW) in carbon dioxide-assisted pyrolysis process. Compared to the generation amounts of syngas (0.7 mole% H₂ & 3.0 mole% CO) at 700℃ from single pyrolysis of CW, co-pyrolysis in the presence of Fe- or Zr-based additives resulted in the enhanced production of syngas, with the measured concentrations of H₂ and CO ranging 1.1-3.4 mole% and 4.6-13.2 mole% at the same temperature, respectively. In addition, α-Fe₂O₃ biochar possessed the adsorption capacity of As(V) (19.3 mg g^-1) comparable to that of ZrO₂-biochar (21.2 mg g^-1). In conclusion, solid-type Fe-based additive can be highly considered as an efficient catalyst to simultaneously produce syngas (H₂ & CO) as fuel energy resource and metal-biochar as sorbent.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.3
• /
• pp.43-46
• /
• 1986

A stainless steel autoclave reactor, which is the property of Pacific Northwest Laboratories(PNL) and located in PNL, was acted for pyrolysis and gasification of sawdust, ricestraw, and ricehusk. The initial reaction temperature of this reactor was 300$^{\circ}C$, and up to 500$^{\circ}C$ to complete pyrolysis and gasification reaction. The maximum exerted pressure on this reactor was 800 psig. In order to examine the effect of catalyst on reaction temperature, $K_2CO_3$, and nickel/alkali carbonate catalyst mixture were also used. The experimental results obtained with this reactor indicated that good yields of methane-rich gas(exceeding 40% methane) can be produced. The product gas mixtures were also identified to be CO. $CO_2$, $C_2H_4$, and $CH_3CHO$ etc. by Gas Chromatography and Mass Spectrometer.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.1
• /
• pp.79-87
• /
• 2015

A thermochemical equilibrium model was constructed for predicting composition of synthesis gas in biomass gasification. The model included estimation of equilibrium constants using Gibbs free energy. After constructing the model, the results were compared with the experimental values and predictions from a previous model. Gas compositions were reasonably well agreed with them and showed effects of operational and fuel condition. When the reaction temperature increased, the lower heating values decreased due to the decrease in CH4 concentrations. The methane concentrations were lower than those observed in experimental results. The model was used to predict the gas composition and heating values for the cases of mixed fuel of charcoal and un-dry woodchips. Although downdraft gasifiers require fuels less than 15% of moisture contents, the model results indicated that the mixed fuel with charcoal and woodchips which had over 25% of moisture contents could be used in the downdraft gasifiers. It might be explained by increase in energy density resulting from mixing charcoal. The results imply that the efforts and costs for drying biomass fuels could be reduced by mixing charcoal or fuels with higher calorific values.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.4
• /
• pp.231-236
• /
• 2014

Sawdust, produced as an wood by-product, is usable biomass as liquid fuels if decomposed to monomer unit, because the chemical structure are similar to high octane materials found in gasoline. In this study, parameters of thermochemical degradation by acetone-solvolysis reaction of sawdust such as the effect of reaction temperature, reaction time and type of solvent on conversion yield and degradation products were investigated. The liquid products by acetone-solvolysis from sawdust produced various kind of ketone, phenol and furan compounds. The optimum sawdust conversion was observed to be 88.7% at $350^{\circ}C$, 40min. Combustion heating value of liquid products from thermochemical conversion processes was as high as 7,824 cal/g. The energy yield and mass yield in acetone-solvolysis of sawdust was 60.8% and 36.4 g-oil/100g-sawdust after 40 min of reaction at $350^{\circ}C$, respectively. The major components of the acetone-solvolysis products, that could be used as liquid fuel, were 4-methyl-3-pentene-2-one, 1,3,5-trimethylbezene, 2,6-dimethyl-2,5-heptadiene-4-one, 3-methyl-2-cyclopenten-1-one as ketone compounds.

• Journal of Powder Materials
• /
• v.1 no.2
• /
• pp.208-216
• /
• 1994

A radically new approach to the in situ synthesis of the consituent phases of a composite structure has enabled the production of a new WC/Co materials with an ultrafine microstructure. The process for synthesizing nanophase WC/Co powders consists of spray drying from solution to form a homogeneous precursor powder, and thermochemical conversion of the precursor powder to the nanophase WC/Co powder. Near theoretical density of pure nanophase WC-10 wt%Co has been obtained in only 30 sec at 140$0^{\circ}C$. But WC particles were grown up very rapidly with longer sintering time to get full density. To overcome coarsening of WC particle during sintering, VC, TaC and VC/TaC were used as the grain growth inhibitor with different amount respectively. VC/TaC doped WC-10 wt%Co was shown superior hardness and TRS and microstructure was maintained ultrafine scale (average WC size is less than 0.1 ${\mu}{\textrm}{m}$).

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.2
• /
• pp.21-28
• /
• 1986

A quartz type gasification reactor was designed and used for pyrolysis and gasification of sawdust, ricestraw and ricehusk. The initial reaction temperature was 350$^{\circ}C$, and up to 550$^{\circ}C$ to complete pyrolysis and gasification reaction. In order to examine the effect of catalyst on reaction temperature, $K_2CO_3$ and $Na_2CO_3$ as catalyst were also used. The product gas mixtures are identified to be CO, $CO_2$, $CH_4$ and $CH_3CHO$ etc. by Gas Chromatography and Mass Spectrometer. The highest gas volume of the gasified sawdust at 550$^{\circ}C$ amounts to 1800ml/g of sawdust, even though the yield and composition of this product gas are depending on the reaction temperature of the reactor and catalyst used.