• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.7
• /
• pp.196-202
• /
• 1999

Recent trend changes a criterion for evaluation of burner that environmental problem is raised as global issue. For efficient driving problem, the higher thermal efficiency and the lower oxygen in exhaust gas, burner is evaluated the better. For environmental problem, burner must satisfy $NO_{X}$ limit and CO limit. Consequently, 'good burner' means on whose thermal efficiency is high under the constraint of $NO_{X}$ and CO consistency. To make existing burner satisfy recent criterion, it is highly recommended to develop feedback control scheme whose output is the consistency of $NO_{X}$ and CO. This paper describes development of real time flame diagnosis technique that evaluate and diagnose combustion state such as consistency of components in exhaust gas, stability of flame in quantitative sense. This study focuses on wave length of luminescence from chemical reaction measurement of the luminescence via optical measuring apparatus and derive correlation with consistency of components in exhaust gas by image processing technique.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.5
• /
• pp.81-88
• /
• 2013

A low voltage circuit breaker protects electrical equipments from over current and short faults of system by cutting the power supply. The breaker use a thermal magnetic type trip device from the past. In recent years, electronic type relays are applied due to useful functions and services. The purpose of this development is full digitalizing of relay functions of a low voltage breaker. It includes separation of current sensor from current transformer, digital signal processing, high speed relaying, and voltage measuring for power meter. The suggestions are tested and implemented by making prototype and testing its all relay functions.

• Laser Solutions
• /
• v.4 no.3
• /
• pp.40-44
• /
• 2001

Microbump formation during CO$_2$ laser texturing of glass substrates is examined in this paper. Experimental results show that different bump shapes (dome-shaped, with a central dimple, and with a peripheral rim) are generated depending on the laser fluence. A theoretical model for the process is suggested based on thermoelastic behavior but limited only to the dome-shaped bump. The dimensions (maximum height and base area) of the bump shows a logarithmic dependence on laser fluence as expected from the theory. Numerical computation reveals that the effect of thermal diffusion is not negligible for relatively long laser pulses.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.953-954
• /
• 2006

Ti-Cu-Ni-Sn quaternary amorphous alloys of $Ti_{50}Cu_{32}Ni_{15}Sn_3$, $Ti_{50}Cu_{25}Ni_{20}Sn_5$, and $Ti_{50}Cu_{23}Ni_{20}Sn_7$ composition were prepared by mechanical alloying in a planetary high-energy ball-mill (AGO-2). The amorphization of all three alloys was found to set in after milling at 300rpm speed for 2h. A complete amorphization was observed for $Ti_{50}Cu_{32}Ni_{15}Sn_3$ and $Ti_{50}Cu_{25}Ni_{20}Sn_5$ after 30h and 20h of milling, respectively. Differential scanning calorimetry analyses revealed that the thermal stability increased in the order of $Ti_{50}Cu_{32}Ni_{15}Sn_3$, $Ti_{50}Cu_{25}Ni_{20}Sn_5$, and $Ti_{50}Cu_{23}Ni_{20}Sn_7$.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.171-174
• /
• 2005

The circuit simulation analysis and diagnosis methods are used to instruments in detail when they give apparently abnormal readings. In this paper, a new simulator through an analysis of the important circuits modeling under severe accident conditions has been designed, the realization for a body work instead of the two sorts of the Labview & Pspice as an one order command in the Labview program. The program can be shown the output graph form the circuit modeling as an order commend. The procedure for the simulator design was divided into two design steps, of which the first step was the diagnosis methods, the second step was the circuit simulator for the signal processing tool. It has three main functions which are a signal processing tool, an accident management tool, and an additional guide from the initial screen.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.8
• /
• pp.11-16
• /
• 2008

In this paper, firstly we made of the rapid thermal processor equipment with the specifically useful structure to measure wafer stress. Secondly we made of the laser interferometry to inspect the wafer surface curvature based on the large deformation theory. And then the wafer surface fringe image was obtained by experiment, and the full field stress distribution of wafer surface comes into view by signal processing with thining and pitch mapping. After wafer was ground by 1mm and polished from the back side to get easily deformation, and it was heated by three to four times thermal treatments at about 1000 degree temperature. Finally the severe deformation between wafer before and after the heat treatment was shown.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.4
• /
• pp.275-281
• /
• 2016

One of the most important things for quality to meet ship-production schedule is an accuracy control. A ship is assembled by welding through whole production process, so it is important that loss by correction will not happen as much as possible by using some engineering skills like reverse design, reverse setting and margin for thermal shrinkage. These efforts are a quite effective in fabrication stages, but not in erection stages. If a ship block which consists of common steel is exposed to directional solar radiation, its dimensional accuracy will change high as time by its thermal expansion coefficient. Therefore, the measuring work would be often done at dawn or evening even with having a very accurate device. In this study, an FE analysis method is developed to solve this problem. It can change measured data affected by solar thermal distortion to ones not, even though ship-block is measured at an arbitrary time. It will use the time when measuring, the direction of block and the weather record by satellites. It is confirmed by a comparison between measured data of a ship-block and the result by suggested analysis method. Furthermore, a pre-processing system is also developed for fast application of the suggested analysis method.

• Journal of the Korean Ceramic Society
• /
• v.43 no.5 s.288
• /
• pp.293-298
• /
• 2006

For substrate glass applied to PDP (Plasma Display Panel), it has been developed many glass compositions that have to not only meet the specifications of PDP but also satisfy the float process as production technology. In the present work several compositions with no deformation at PDP processing temperature and thermal expansion coefficient of $83{\sim}9{\times}10^{-7}/K$ were designed. Based on viscosity at high temperature and liquidus temperature for those compositions, three candidate compositions named T-2, T-4, T-6 were selected finally. It was examined additionally that thermal shrinkage at PDP processing temperature and visible transmittance. The properties of T-series were compared with those of commercial glasses and discussed from the view point of PDP device and glass production.

• Journal of Ceramic Processing Research
• /
• v.20 no.6
• /
• pp.582-588
• /
• 2019

FeVSb1-xTex (0.02 ≤ x ≤ 0.10) half-Heusler alloys were fabricated by mechanical alloying process and subsequent vacuum hot pressing. Near single half-Heusler phases are formed in vacuum hot pressed samples but a second phase of FeSb2 couldn't be avoided. After doping, the lattice thermal conductivity in the system was shown to decrease with increasing Te concentration and with increasing temperature. The lowest thermal conductivity was achieved for FeVSb0.94Te0.06 sample at about 657 K. This considerable reduction of thermal conductivities is attributed to the increased phonon scattering enhanced by defect structure, which is formed by doping of Te at Sb site. The phonon scattering might also increase at grain boundaries due to the formation of fine grain structure. The Seebeck coefficient increased considerably as well, consequently optimizing the thermoelectric figure of merit to a peak value of ~0.24 for FeVSb0.94Te0.06. Thermoelectric properties of various Te concentrations were investigated in the temperature range of around 300~973 K.

• Journal of Mechanical Science and Technology
• /
• v.14 no.5
• /
• pp.477-482
• /
• 2000

This study discusses a non-contact optical technique (electronic speckle pattern interferometry) that is well suited for thermal deformation measurement without any surface preparation and compensating process. Fiber reinforced plastics ($[0]_{16},\;[0/90]_{8S}$) were analyzed by ESPI to determine their thermal expansion coefficients. The thermal expansion coefficient of the transverse direction of a uniaxial composite is evaluated as $48.78{\times}10^{-6}(1/^{\circ}C)$. Also, the thermal expansion coefficient of the cross-ply laminate $[0/90]_{8S}$ is numerically estimated as $3.23{\times}10^{-6}(1/^{\circ}C)$ that is compared with that measured by ESPI.