• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.1
• /
• pp.62-71
• /
• 2015

Geostationary satellites use the thruster in order to control the location change and mount the suitable amount of liquid propellant depending on the operating lifetime. Therefore the lifetime of the geostationary satellite depends on the residual propellant amount and the precise residual propellant gauging is very important for the mitigation of economic losses arised from premature removal of satellite from its orbit, satellites replacement planning, slot management and so on. The propellant gauging methods of geostationary satellite are mostly used PVT method, thermal mass method and bookkeeping method. In this paper, we analysis the modeling of COMS(Communication, Ocean & Meteorological Satellite) bipropellant system for bookkeeping method and COMS GTO(Geostationary Transfer Orbit) injection propellant estimation using Monte-Carlo method.

• The Korean Journal of Ceramics
• /
• v.1 no.4
• /
• pp.191-196
• /
• 1995

Using sol-gel processing method, thin films of lathanum modified lead titanate(PLT) on Corning 7059 glass were prepared. A differential thermal analysis (DTA/TG) curve of gel powder and infrared spectra (FT-IR) of the films were measured to estimate residual organices in them. The heat-treated films were characterized by X-ray diffraction(XRD). Microstructures of the films were observed by a scanning electron microscope (SEM). Optical properties of the films were determined by a UV-VIS spectrophotometer. The waveguiding properties and optical attenuation were measured with the end coupling method and the cut back method. Effects of the drying conditions on the transmittance and the propagation loss of the films were investigated. Experimemtal results showed that the content of residual organics in the film decreased as the drying temperature of the film increased. As the La content of the film increased, the grain size decreased and the transmittance increased. The transmittances of the films increased with the increasing of the drying temperature. The propagation losses in the film decreased as the drying temperature increased.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2070-2075
• /
• 2004

Performance of a solid oxide fuel cell (SOFC) can be enhanced by converting thermal energy of its high temperature exhaust gas to mechanical power using a micro gas turbine (MGT). A MGT plays also an important role to pressurize and warm up inlet gas streams of the SOFC. In this study, the influence of performance characteristics of the tubular SOFC on the hybrid power system is discussed. For this purpose, detailed heat and mass transfer with reforming and electrochemical reactions in the SOFC are mathematically modeled, and their results are reflected to the performance analysis. The analysis target is 220kWe SOFC/MGT hybrid system based on the tubular SOFC developed by Siemens-Westinghouse. Special attention is paid to the ohmic losses in the tubular SOFC counting not only current flow in radial direction, but also current flow in circumferential direction through the anode and cathode.

• Archives of Pharmacal Research
• /
• v.2 no.1
• /
• pp.49-64
• /
• 1979

In an atempt to elucidate further physicochemical properties of furosemide-PVP coprecipitates, extensive investigations such as TLC, UV,IR, NMR, X-ray diffraction, TGA and DTA studies were carried out for the furosemide test systems. X-ray diffraction studies revealed that the pure furosemide and the furosemide contained within a physical mixture were crystalline in nature. However, there was no crystallinity evident in the 1:5 furosemide-PVP 40,000 coprecipitate system, even after standing for two years. The various ratio furosemide-PVP 40,000 coprecipitate systems revealed that the coprecipitate containing a greater amount of PVP 40,000 than that of furosemide showed a crystalline state of furosemide and that the minimum amounts of PVP to make amorphous form of furosemide was 1:1 ratio of furosemide to PVP. From the furosemide-PVP coprecipitate systems with PVP of different molecular weights of 10,000, 40,000 and 360,000, all the 1:1 ratio coprecipitates did not exhibit any crystallinity of furosemide, whereas all the 2:1 ratio coprecipitates showed a presence of crystalline furosemide. All the coprecipitated preparations with PEG 4,000 and with PEG 6,000 showed the diffraction peaks indicating the presence of crystalline furosemide. The comparison of infrared spectra of the physical mixture and the coprecipitate showed an interaction such as association between the functional groups of furosemide and PVP in the molecular level, whereas the studies by TLC, UV and NMR showed its dissociation in methanol solution. The weight losses in TGA curves showed all the same patterns. However, a little different transition form in DTA thermograms was shown between the physical mixture and the coprecipitate, indicating the different thermal property.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2016

Ensuring the secure operation of power systems has become an important and critical matter during the present time, along with the development of large, complex and load-increasing systems. Security constraints such as the thermal limits of transmission lines and bus-voltage limits must be satisfied under all of a system’s operational conditions. An alternative solution to improve the security of a power system is the employment of Flexible Alternating-Current Transmission Systems (FACTS). FACTS devices can reduce the flows of heavily loaded lines, maintain the bus voltages at desired levels, and improve the stability of a power network. The Unified Power Flow Controller (UPFC) is a versatile FACTS device that can independently or simultaneously control the active power, the reactive power and the bus voltage; however, to achieve such functionality, it is very important to determine the optimal location of the UPFC device, with the appropriate parameter setting, in the power system. In this paper, a genetic algorithm (GA) method is applied to determine the optimal location of the UPFC device in a network for the enhancement of the power-system loadability and the minimization of the active power loss in the transmission line. To verify our approach, simulations were performed on the IEEE 14 Bus, 30 Bus, and 57 Bus test systems. The proposed work was implemented in the MATLAB platform.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.587-590
• /
• 2003

The first attention in designing a transformer for low temperature rise should be to reduce losses. Leakage inductance and temperature rise are two of the more impotent problems facing the magnetic core technology of today's high frequency transformers. Excessive leakage inductance increases the stress on the switching transistors and limits the duty-cycle, and excessive temperature rise can lead the design limitation of high frequency transformer with high current. The flat transformer technology provides a very good solution to the problems of leakage inductance and thermal management for high frequency power. The critical magnetic components and windings are optimized and packaged within a completely assembled module. The turns ratio in a flat transformer is determined as the product of the number of elements or modules times the number of primary turns. The leakage inductance increase proportionately to the number of elements, but since it is reduced as the square of the turns, the net reduction can be very significant. The flat transformer modules use cores which have no gap. This eliminates fringing fluxes and stray flux outside of the core. The secondary windings are formed of flat metal and are bonded to the inside surface of the core. The secondary winding thus surrounds the primary winding, so nearly all of the flux is captured.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.406-415
• /
• 2008

Recently, the amount of thermosetting plastic wastes have increased with the production of reinforced plastic composites and causes serious environmental problems. The epoxy composites, one of the versatile thermosetting plastics with excellent properties, cannot be melted down and remolded as what is done in the thermoplastic industry. In this research, a series of experiments that recovers carbon fibers from carbon fiber reinforced epoxy composites for train body was performed. We experimentally examined various decomposition processes and compared their decomposition efficiencies and mechanical property of recovered carbon fibers. For the prevention of tangle of recovered carbon fibers, each composites specimen was fixed with a Teflon supporter and no mechanical mixing was applied. Decomposition products were analyzed by scanning electron microscope (SEM), gas chromatography mass spectrometer (GC-MS), and universal testing machine (UTM). Carbon fibers could be completely recovered from decomposition process using nitric acid aqueous solution, liquid-phase thermal cracking and pyrolysis. The tensile strength losses of the recovered carbon fibers were less than 4%.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.5
• /
• pp.443-450
• /
• 2006

The present study has been conducted to investigate the effects of rotation on heat/mass transfer and pressure drop characteristics in a two-pass square duct with and without discrete ribs. For stationary cases, the heat/mass transfer on the surfaces with and without discrete ribs is almost the same or reduced. For rotating cases, the gap flow affects differently the heat/mass transfer on leading and trailing surfaces with discrete ribs. On the leading surface of the first pass, the heat/mass transfer is slightly enhanced due to generating strong gap flow. On the trailing surface of the first pass, however, the heat/mass transfer is much decreased because the gap flow disturbs impingement of main flow. The phenomenon, that is, the heat/mass transfer discrepancy between the leading and trailing surfaces is distinctly presented with the increment of rotation number. The friction losses on each surface with discrete ribs are reduced because the blockage ratio decreases for both non-rotating and rotating cases. Therefore, high thermal performance appears in a duct with discrete ribs.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.52-57
• /
• 2018

Most current ships have adopted on-board diesel generators to produce electricity, but the overall efficiency of equipment is down to about 50% due to thermal losses from operations such as exhaust gas, jacket water cooler, scavenge air cooler, etc. Recently, fuel cells have been highlighted as a promising technology to reduce the effect on the environment and have a higher efficiency. Therefore, this paper suggested a solid oxide fuel cell (SOFC)-gas turbine (GT) using waste heat from a SOFC and SOFC-GT-steam turbine (ST) with Rankine cycle. To compare both configurations, the fuel flow rate, current density, cell voltage, electrical power, and overall efficiency were evaluated at different operating loads. The overall efficiency of both SOFC hybrid systems was higher than the conventional system.

• Food Engineering Progress
• /
• v.22 no.4
• /
• pp.283-294
• /
• 2018

Food allergy is a chronic disease that is increasing all over the world, and it can even lead to a loss of life. To prevent any incidents resulting from food allergies, most countries keep strengthening their food allergen labeling requirements domestically and internationally, with a constant monitoring system against undeclared allergens and recall of offending products. In order to avoid economic losses to industry and damages to international relations from undeclared allergens, it is necessary to confirm each country's regulatory policy on food allergen labeling prior to exportation. Another required action is to try for a reduction of the cross-contamination risk of the allergens during manufacturing and storage, which should be verified by using an accurate and reliable analysis of food allergens. This paper is intended to provide an introduction to the regulation of food allergen labeling by country, allergen management methods to avoid cross-contamination, and allergen detection methods using ELISA, PCR, and LC/MS. Changes of allergenicity during thermal or nonthermal processing also will be investigated in our review. This review will be helpful for the food industry to better understand patients suffering from food allergies and to manage food allergens in food manufacturing.