• Polymer(Korea)
• /
• 제24권2호
• /
• pp.228-236
• /
• 2000

The preparation of organophilic clay from Na$^{+}$-MMT was achieved by intercalation of alkylammonium bromide. The dispersed organophilic clay in NMP was then added to the solution of polyamic acids (BPDA-PPD, BTDA-ODA/ MPD) in NMP. After curing at 30$0^{\circ}C$, thin films of the polyimide/clay nanocomposite were prepared. The results of X-ray diffraction (XRD) shelved that the d-spacings of dried polyamic acid (PAA)-clay complexes increased in proportion to the chain length of the onium ion and patterns of two kinds of PAA-clay complexes were similar. The d-spacings of approximately 13.2 $\AA$ for the polyimide/clay nanocomposites were independent of the initial onium ion chain length and the species of PAA. From the study of XRD and transmission electron microscopy (TEM), we found layered silicates were dispersed in polyimide matrix and the resultants were intercalated nanocomposites. TGA result showed thermal stability of polyimide nanocomposite improved a little more than the pure polyimide. From the result of dynamic mechanical property, we found that the storage modulus of the nanocomposites had increased by 1.2-1.8 times of the pure polyimides.s.

• Restorative Dentistry and Endodontics
• /
• 제20권1호
• /
• pp.142-151
• /
• 1995

The purpose of this study was to compare and estimate the physical properties of five root canal sealers classified Calciobiotic root canals sealer as calcium hydroxide based sealer, Apatite root sealer type II as calcium phosphate based sealer, AH-26 as resin based sealer, Canals and Pulpdent root canals sealer as zinc oxide eugenol based sealer. The author investigated dimensional change and flow rate of canal sealers, diametral tensile strength and shear bond strength of sealers to dentin to evaluate the physical properties on affect of complete obturation of root canal and performed the total 100 specimens of each 25 sealers under the condition of root temperature according to manufacturer's instructions. All specimens were stored at $37{\pm}1^{\circ}C$ in 100 % relative humidity. A microscope for measurement of micro distance is used for the dimensional change test and evacuation methods using vaccum were used for the flow rate test. The result differed by the storage time measured on the tests of diametral tensile strength and shear bond strength to dentin. The following results were obtained ; 1 On the test of dimensional change, Canals and Pulpdent expanded slightly, AH-26 and Apatite showed the severe shrinkage after 48 hours. 2. AH-26 and Apatite were the excellent with each 24.59mm, 31.19mm after 3 minutes in the aspect of flow property. 3. On the diametral tensile strength, Calciobiotic root canals sealer showed the highest strength with 27.13kg/$cm^2$ after 48 hours, Apatite root sealer type II showed highest strength with 84.57kg/$cm^2$ after 120 hours. 4. On the shear bond strength to dentin, AH-26 was most excellent with 55.73kgf/$cm^2$ after 24 hours and with 134.71kgf/$cm^2$ after 120 hours.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.310-316
• /
• 2010

Recently a fuel oil of the diesel engine of the marine ship is being changed with heavy oil of low quality as the oil price is higher more and more. Therefore the wear and corrosion in all parts of the engine such as cylinder liner, piston crown, spindle and seat ring of exhaust valves are predominantly increased. In particular the degree of wear and corrosion of piston crown is more seriously compared to the other parts of the engine due to operating in severe environment such as the high temperature of exhaust gas and repeating impact. Thus the repair weldment of the piston crown is a unique method to prolong the its life in a economical point of view. In this case, filler metals having a high corrosion and wear resistance such as stellite 6, Inconel 625 and Inconel 718 are mainly being used for repair welding. However it has been often happened that piston crown on the ship,s job site is being actually inevitably welded with mild filler metals. Therefore in this study, filler metals such as E4301, E4313 and E4316 were welded at SS401 steel as the base metal, and corrosion property of their weld metals in the case of post weld heat treatment or not was investigated with some electrochemical methods such as measurement of corrosion potential, cathodic and anodic polarization curves, cyclic voltammogram and polarization resistance etc. in 0.1% $H_2SO_4$ solution. Corrosion resistance of the weld metal of E4301 was better than the other weld metals in the case of no heat treatment, however, its resistance was considerably decreased with post weld heat treatment(annealing:$625^{\circ}C$, 2 hr) compared to other weld metals. The weld metals of E4313 and E4316 showed a relatively good corrosion resistance by post weld heat treatment.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• 제35권3C호
• /
• pp.295-301
• /
• 2010

In this paper, we propose a new mouthpiece model for the electronic wind instrument using a propeller and linear analysis for fast tracking wind velocity blown. This method is a modification of the velocity anemometer for fast tracking wind velocity by the propeller's angular velocity (speed of revolution). In the case of velocity anemometer, wind velocity is calculated using the property that wind velocity is in proportion to the propeller's angular velocity. However, wind velocity and angular velocity of the propeller are not in one-one correspondence because wind velocity takes some transitional time for the expected wind velocity to be calculated from angular velocity. To resolve this problem, we propose a method for finding the impulse response of the system which can be considered as a linear system, and for estimating the wind velocity by deconvolving the propeller's angular velocity with the impulse response. To experiment and to prove the validity of the proposed system, we designed a mouthpiece model which consists of a motor, a propeller and an encoder. The result of estimated wind velocity in this method showed that this system is about eightfold faster than the method by the conventional velocity anemometer.

• Composites Research
• /
• 제22권2호
• /
• pp.30-36
• /
• 2009

In this paper, we propose the design method for the composite torque link of a landing gear for a helicopter. The composite torque link has to be light weighted and very stiff to keep the shock absorber in the landing gear of helicopter. The configuration and structural shape has to be designed in consideration of the RTM (Resin Transfer Molding) manufacturing process which is adopted to minimize the manufacturing cost. The mechanical properties are obtained through the coupon tests with the specimens made by the same manufacturing process for the composite structure. The optimal design process was performed through iterative modifications of the models which were verified by stress analysis using FEM. The composite torque link has lug-shaped parts and is very thick, so 3D Layered solid elements of ABAQUS were used to get the stress field including the stress components in thickness direction and non-linear static analysis using contact B.C. of rigid-deform condition was used to get the optimal design.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 한국에너지공학회 2002년도 춘계 학술발표회 논문집
• /
• pp.227-234
• /
• 2002

With the increasing environmental consideration and stricter regulations, gasification of waste is considered to be more attractive technology than conventional incineration for energy recovery as well as material recycling. The experiment for combustible waste mixed with plastic and cellulosic materials was performed in the fixed bed gasifier to investigate the gasification behavior with the operating conditions. Waste pelletized with a diameter of 2~3cm and 5cm of length was gasified at the temperature range of 1100~145$0^{\circ}C$. It was shown that the composition of H$_2$ was in the range of 30~40% and CO 15~30% depending upon oxygen/waste ratio. Casification of waste due to thermoplastic property from mixed plastic melting and thermal cracking shows a prominent difference from that of coal or coke. It was desirable to maintain the top temperature up to foot to ensure the mass transfer and uniform reaction through the packed bed. As the bed height was increased, the formation of H$_2$ and CO was increased whilst $CO_2$ decreased by the char-$CO_2$ reaction and plastic cracking. From the experimental results, the cold gas efficiency was around 61% and heating values of product gases were in the range of 2800~3200㎉/Nm3.

• The Korean Journal of Food And Nutrition
• /
• 제22권2호
• /
• pp.261-271
• /
• 2009

Deep sea water exists at depths of over 200m under the sea. As no sunlight reaches it, photosynthesis does not take place within it, and it contains no organic matter. In addition, its temperature is maintained at a stable low level throughout the year, so it does not get mixed with the sea water on the surface. It contains a large amount of nutritious salts, whose cleanness is maintained. It is a marine resource that has matured for a long period of time. Research into deep sea water, which started in the 1970s, has been made around the whole world, including the USA and Japan. In Korea, research has been active in this area since 2000. As there has been a good amount of research into industrial applications for deep sea water, since 1993, patents for the relevant technologies have been applied. This paper intends to provide a resource to researchers of deep sea water, by summarizing of all domestic deep sea water-related patents applied with Korean Intellectual Property Office from 1993 to 2008. This research was conducted using a computer and KIPRIS Database owned by the Korea Institute of Patent Information. 'Deep sea water' was used as the search keyword. A total of 222 Korean patents relating to deep sea water have been registered on the basis of IPC. Of these, 126 patents relate to the manufacturing and the treatment of foods, foodstuffs, or non-alcoholic beverages(A23L), while 50 patents relate to the production for medical, dental, or cosmetic purposes(A61K). 38 patents relate to water purification, treatment of wastewater, sewage and sludge (C02F), while 8 patents relate to fishery and farming(A01K). In summary, it was found that studies for the practical use of deep sea water have been conducted in relation to the manufacturing and the treatment of foods, foodstuffs, beverages, and cosmetics.

• Journal of the Korea Institute of Building Construction
• /
• 제15권2호
• /
• pp.177-183
• /
• 2015

In this study, the thermal conductivity, physical and mechanical properties of lightweight aggregate concretes with hollow micro sphere(HMS) are experimentally examined as a basic research for the development of structural insulation concrete. As the results of this experiment, in the case of concrete mixed with HMS, the value of slump has been reduced, so it is found that the dosage of superplasticizer should be increased. As the replacement ratio of HMS increases, it has shown that the compressive strength is somewhat decreased due to the low interfacial adhesion strength of HMS. But the thermal conductivity is found to be greatly improved with the replacement ratio of HMS increases, the thermal conductivity of HMS shows the lower value of 68% at lightweight aggregate concrete and 32% of normal concrete. Also it is found that the compressive strength is decreased and thermal conductivity is increased as the water-cement ratio increases. The most outstanding for insulation performance is observed when using 20% of HMS and 50% of water-cement ratio.

• Journal of Ginseng Research
• /
• 제19권3호
• /
• pp.225-230
• /
• 1995

The effect of long-term ginseng (Panax ginseng C.A. Meyer) administration on the clearance of carboxyhemoglobin (CO-Hb) and the property of blood gases was investigated in rats. Rats were received ginseng water extract (0.025% in drinking water) for 42 weeks starting at the age of 6 weeks. They were exposed to the diluted mainstream smoke generated from 15 filter cigarettes for 20 min in a round polycarbonate chamber (D37 cmXH13 cm). Under this condition, the mean CO-Hb content of control and the ginseng-treated rats immediately after the exposure was nearly the same as 13.8$\pm$2.9 f) and 13.9$\pm$1.6%, respectively. However, CO-Hb was more rapidly removed from blood in the ginseng treated rats than in untreatEd control with the laps of time, namely, its biological half life In the former was 36.9$\pm$1.5 min and in the latter was 56.9$\pm$13.2 min. Although long-term ginseng treatment did not affect the content of hemoglobin and blood pH of rats, it slightly increased blood oxygen content and its partial pressure value, and decreased levels of carbon dioxide and bicarbonate. These results suggest that long-term administration of rats with ginseng extract accelerate the elimination of CO from the blood. This effect seems to be related to the enhancement of oxygen consumption of the rat by a certain action of ginseng components as previously reported.

• Journal of Korean Society of Forest Science
• /
• 제22권1호
• /
• pp.1-6
• /
• 1974

In order to improve decaying properties of the plywood the effectiveness of the Malenit treatment on the shear strength and decaying properties of the plywood has been investigated. The results are as follows. 1. No decrease of the shear strength of the plywood has shown despite of whether plywood treated with malenit right after plywood made or veneer treated with the same preservative prior to plywood manufactured. 2. The effectiveness of Malenit treatment on decaying property of the plywood has shown much greater than that of the untreated plywood and red pine sapwood. 3. Weight decreases of the test specimens due to the infection of the different fungi have seen in different ways. If fungi infected are all different in kinds, weight decreases of the specimens are different in it's degree due to the fungi.