• Title/Summary/Keyword: the fitted shape

Search Result 187, Processing Time 0.024 seconds

Effect of Adhesives and Finger Pitches on Bending Creep Performances of Finger-Jointed Woods

  • Park, Han-Min;Oh, Seong-Won;Byeon, Hee-Seop
    • Journal of the Korean Wood Science and Technology
    • /
    • v.33 no.5 s.133
    • /
    • pp.57-65
    • /
    • 2005
  • Following our previous reports for finger-jointed woods with various finger profiles studied for the efficient use of small diameter logs and woods containing various defects, twelve types of finger-jointed woods glued with three kinds of adhesives and with two sizes of finger pitches were made with sitka spruce and red pine. The effects of the adhesives and finger pitches on bending creep performances of finger-jointed woods were investigated. The shape of creep curves differed among the used adhesives and finger pitches of finger-jointed woods for both tested species. Their creep curves showed a linear behavior beyond about one hour, and the N values fitted to power law increased with increasing finger pitches. The initial deformation increased with increasing finger pitches, regardless of the tested species and kinds of adhesives, whereas the effect of finger pitches on the creep deformation was not clear. For finger-jointed woods glued with polyvinyl acetate (PVAc) resin, creep failure occurred in 106 hours after the load was applied. And the difference of the creep compliance between finger-jointed woods glued with resorcinol-phenol formaldehyde (RPF) resin and aqueous vinyl urethane (AVU) resin was small. The ratios for creep performances of finger-jointed woods glued with RPF resin and AVU resin versus solid wood were higher in creep deformation than initial deformation for both species, and the difference between both adhesives was not found. The relative creep decreased with increasing finger pitches, and the marked differences was not found between RPF resin and AVU resin.

Investigation of mean wind pressures on 'E' plan shaped tall building

  • Bhattacharyya, Biswarup;Dalui, Sujit Kumar
    • Wind and Structures
    • /
    • v.26 no.2
    • /
    • pp.99-114
    • /
    • 2018
  • Due to shortage of land and architectural aesthetics, sometimes the buildings are constructed as unconventional in plan. The wind force acts differently according to the plan shape of the building. So, it is of utter importance to study wind force or, more specifically wind pressure on an unconventional plan shaped tall building. To address this issue, this paper demonstrates a comprehensive study on mean pressure coefficient of 'E' plan shaped tall building. This study has been carried out experimentally and numerically by wind tunnel test and computational fluid dynamics (CFD) simulation respectively. Mean wind pressures on all the faces of the building are predicted using wind tunnel test and CFD simulation varying wind incidence angles from $0^{\circ}$ to $180^{\circ}$ at an interval of $30^{\circ}$. The accuracy of the numerically predicted results are measured by comparing results predicted by CFD with experimental results and it seems to have a good agreement with wind tunnel results. Besides wind pressures, wind flow patterns are also obtained by CFD for all the wind incidence angles. These flow patterns predict the behavior of pressure variation on the different faces of the building. For better comparison of the results, pressure contours on all the faces are also predicted by both the methods. Finally, polynomial expressions as the sine and cosine function of wind angle are proposed for obtaining mean wind pressure coefficient on all the faces using Fourier series expansion. The accuracy of the fitted expansions are measured by sum square error, $R^2$ value and root mean square error.

Membrane Fouling Models for Activated Sludge Cakes (활성슬러지 케이크의 분리막 오염 모델)

  • Kim, Dae Chun;Chung, Kun Yong
    • Membrane Journal
    • /
    • v.24 no.3
    • /
    • pp.249-257
    • /
    • 2014
  • This experiment was carried out for a laboratory scale activated sludge bioreactor equipped with submerged flat sheet membrane using the synthetic wastewater. The membrane system for the activated sludge solution of MLSS 5,000 mg/L was operated with constant permeate flux by continuously permeating and periodically 10 minute-permeating/2 minute-resting modes, respectively. The transmembrane pressure was measured as the permeate flux increased from 10 to $25L/m^2{\cdot}hr$ under the constant air flowrate 0.25 L/min. Also, the complete blocking, standard blocking, intermediate blocking, incompressible cake and linear compressible cake fouling models were retrofitted for the experimental data in order to determine the state of the membrane fouling. Because the transmembrane pressure fluctuated as a pulse shape for every period of 10 minute-permeating/2-minute resting mode, the membrane fouling models were separately applied for the maximum and minimum connecting lines. The linear compressible cake fouling model for the activated sludge cakes was the best fitted with the experimental results from the above five models.

Scythai's clothing type and style - focusing on the relationship with ancient Korea - (스키타이 복식 유형 및 형태에 관한 연구 - 고대 한국과의 관계를 중심으로 -)

  • Kim, So-Hee;Chae, Keum-Seok
    • Journal of the Korea Fashion and Costume Design Association
    • /
    • v.20 no.1
    • /
    • pp.61-77
    • /
    • 2018
  • The primary focus of this thesis is to look at Scythai's historical, geographical and ethnologic background in order to understand Scythai's garment types and styles as described in Scythai-related documented records, previous studies and excavated artifacts. Based upon this, another objective lies in comparing and contrasting this information with ancient Korean garments to identify what kind of relationship exists between the two. The result from this study's objectives is summarized as follows. Firstly, ancient Korean and Scythai share similarities in art work, craftwork, accessories and the like, which allows us to make a guess at the relationship between ancient Korea and Scythai of that time. Secondly, Scythai garments are based on the tight and well-fitted Caftan Yugoje, which is tightly fit to the body, as well as including garments similar to the drapery Kiton and Tunic found in ancient Greek garments, from which can be seen that the garment of culture medium passing between the East and the West had nomadic horse-riders' ethnic characteristics and Eurasian characteristics. Thirdly, ancient Korean Scythai garments were found to have homogeneity in their garment culture in that northern nomadic cultural district's Hobok-Goseupje, i.e., open-front Caftan Jeogori and pants called Sangeuihago is its basic with a triangular cone hat shape (transformed hat) and boots, which is the basis for considering that ancient Korea exchanged culture with Scythai, who once lived as active northern nomads. However, it can also be seen that ancient Korea and Scythai garments differed in form depending on region, weather, culture, custom and the like. As such, Scythai and ancient Korea have an aesthetic bond because northern nomads and Scythai exchanged their cultural traits of the times. The evidence supports this idea as it seems that the characteristics of garments that can be considered to be Scythain in style are also commonly discovered in ancient Korean garments.

Effect of Humidity Conditions on Bending Creep Performance of Finger-Jointed Woods

  • Park, Han-Min;Byeon, Hee-Seop
    • Journal of the Korean Wood Science and Technology
    • /
    • v.35 no.5
    • /
    • pp.7-15
    • /
    • 2007
  • To evaluate the durability of finger-jointed woods according to change of humidity conditions, four types of finger-jointed woods glued with different kinds of adhesives and finger pitches were made with Sitka spruce, and the effect of humidity conditions on creep performances was investigated. The shape of creep curves differed among humidity conditions, and the inclination of creep curves was greatest in 85%RH, and lowest in 65%RH. Their creep curves showed a linear behavior beyond approximately one hour, regardless of humidity conditions. The A values of the creep curves fitted to power law increased with increasing relative humidity, whereas the A' values were in order of 30 > 85 > 65%RH unlike the A values. The initial deformation increased with increasing relative humidity, whereas the creep deformation unlike the initial deformation was in order of 85 > 30 > 65%RH, and it was found that the creep deformation of finger-jointed woods indicated the smaller amount in air-dry moisture content rather than in a low moisture content less than 30%RH. Finger-jointed woods with 6.8 mm (L) pitch had the greater creep amount than in those with 4.4 mm (S) pitch in all humidity conditions. The difference of creep amount between both adhesives in all humidity conditions was small. Relative creep at 240 hr was greatest as 62.2~71.9% in 85%RH, and the values indicated 2.1~2.6 times that of 30%RH and 3.0~3.6 times that of 65%RH and were equal or slightly greater than that of solid spruce.

Analytical Study for Performance Evaluation of Studs for Steel Plate Concrete (SC) Walls subjected to Forced Vibration (강제진동을 받는 강판 콘크리트 (SC) 벽체에서 스터드의 성능평가를 위한 해석적 연구)

  • Yi, Seong-Tae
    • Journal of the Korea institute for structural maintenance and inspection
    • /
    • v.20 no.3
    • /
    • pp.75-82
    • /
    • 2016
  • This study analytically reviewed the behavior of steel plate concrete (SC) walls subjected to forced vibration to investigate the effects of shape and arrangement spacing of studs on the behavior spacing of studs in SC wall were carried out. From the analyses, it was noted that the damping ratio obtained from the time history analyses showed overall high value in Half-power Bandwidth method and the lowest value in Fitted Exponential Curve method. And, in half of the design strength, the damping ratio presented approximately 3.0~4.2% and, in the design strength, it was approximately 4.1~5.2%. When the developed studs were used, the damping ratio was reduced slightly and it did not show consistent results between DS1 and DS2. When the distance between the studs increases more than necessary, it was also confirmed that the natural frequency was reduced and the damping ratio was increased.

Estimation of sewer deterioration by Weibull distribution function (와이블 분포함수를 이용한 하수관로 노후도 추정)

  • Kang, Byongjun;Yoo, Soonyu;Park, Kyoohong
    • Journal of Korean Society of Water and Wastewater
    • /
    • v.34 no.4
    • /
    • pp.251-258
    • /
    • 2020
  • Sewer deterioration models are needed to forecast the remaining life expectancy of sewer networks by assessing their conditions. In this study, the serious defect (or condition state 3) occurrence probability, at which sewer rehabilitation program should be implemented, was evaluated using four probability distribution functions such as normal, lognormal, exponential, and Weibull distribution. A sample of 252 km of CCTV-inspected sewer pipe data in city Z was collected in the first place. Then the effective data (284 sewer sections of 8.15 km) with reliable information were extracted and classified into 3 groups considering the sub-catchment area, sewer material, and sewer pipe size. Anderson-Darling test was conducted to select the most fitted probability distribution of sewer defect occurrence as Weibull distribution. The shape parameters (β) and scale parameters (η) of Weibull distribution were estimated from the data set of 3 classified groups, including standard errors, 95% confidence intervals, and log-likelihood values. The plot of probability density function and cumulative distribution function were obtained using the estimated parameter values, which could be used to indicate the quantitative level of risk on occurrence of CS3. It was estimated that sewer data group 1, group 2, and group 3 has CS3 occurrence probability exceeding 50% at 13th-year, 11th-year, and 16th-year after the installation, respectively. For every data groups, the time exceeding the CS3 occurrence probability of 90% was also predicted to be 27th- to 30th-year after the installation.

Clinical Implementation of 3D Printing in the Construction of Patient Specific Bolus for Photon Beam Radiotherapy for Mycosis Fungoides

  • Kim, Sung-woo;Kwak, Jungwon;Cho, Byungchul;Song, Si Yeol;Lee, Sang-wook;Jeong, Chiyoung
    • Progress in Medical Physics
    • /
    • v.28 no.1
    • /
    • pp.33-38
    • /
    • 2017
  • Creating individualized build-up material for superficial photon beam radiation therapy at irregular surface is complex with rice or commonly used flat shape bolus. In this study, we implemented a workflow using 3D printed patient specific bolus and describe our clinical experience. To provide better fitted build-up to irregular surface, the 3D printing technique was used. The PolyLactic Acid (PLA) which processed with nontoxic plant component was used for 3D printer filament material for clinical usage. The 3D printed bolus was designed using virtual bolus structure delineated on patient CT images. Dose distributions were generated from treatment plan for bolus assigned uniform relative electron density and bolus using relative electron density from CT image and compared to evaluate the inhomogeneity effect of bolus material. Pretreatment QA is performed to verify the relative electron density applied to bolus structure by gamma analysis. As an in-vivo dosimetry, Optically Stimulated Luminescent Dosimeters (OSLD) are used to measure the skin dose. The plan comparison result shows that discrepancies between the virtual bolus plan and printed bolus plan are negligible. (0.3% maximum dose difference and 0.2% mean dose difference). The dose distribution is evaluated with gamma method (2%, 2 mm) at the center of GTV and the passing rate was 99.6%. The OSLD measurement shows 0.3% to 2.1% higher than expected dose at patient treatment lesion. In this study, we treated Mycosis fungoides patient with patient specific bolus using 3D printing technique. The accuracy of treatment plan was verified by pretreatment QA and in-vivo dosimetry. The QA results and 4 month follow up result shows the radiation treatment using 3D printing bolus is feasible to treat irregular patient skin.

LACTATION CURVE OF HOLSTEIN FRIESIAN COWS IN THE KINGDOM OF SAUDI ARABIA

  • Ali, A.K.A.;Al-Jumaah, R.S.;Hayes, E.
    • Asian-Australasian Journal of Animal Sciences
    • /
    • v.9 no.4
    • /
    • pp.439-447
    • /
    • 1996
  • Monthly test day production for 12,020 records, were collected from six of the largest specialized dairy farms located in central region of the Kingdom of Saudi Arabia. The records described lactating cows in four parities and two seasons of calving. Monthly test day records were fitted using Wood's model $At{{^b}{_e}}^{-ct}$ with multiple and additive error term. Linear and non-linear regression models were used to find the estimates of the parameters necessary to draw the lactation curves. The shape of the lactation curves of different parities showed that third lactation has the heighest peak (43.08 kg) for linear regression model and (42.08 kg) for non-linear regression model. Fourth lactation has the lowest peak (24.00kg) for linear regression model and (25.64 kg) for non-linear regression models. Cows of second and third lactations reached the peak at 58 day for both linear and non-linear regression models. Cows of first lactation were more persistent and had late peak at 68 and 67 days for both models respectively. While, third lactation cows were lower persistent and had early peak at 58 day for both models. Cows calved at winter months have higher starting values (A), higher ascending slope (b) and higher decending slope (c). Least square means of milk yield of the first four parities and for overall data were 6,653, 7,659, 7,482, 6,988 and 7,614 kg respectively. The corresponding lactation period were 358, 367, 350, 363 and 364 days respectively.

Post-purchase Evaluation on the Maternity Wear on the Current Korean Market by Survey and Wear test

  • Park, Soon-Jee;Lee, Hee-Jung;Suh, Chu-Yeon
    • Journal of Fashion Business
    • /
    • v.11 no.3
    • /
    • pp.15-34
    • /
    • 2007
  • This study was designed to collect a precise information concerning to the preference and evaluations after usage of pregnant Korean woman for the maternity wear bysurvey and wear tests. Through the survey, 212 respondents were asked to answer what type of maternity wear they prefer and what requirements for maternity wear design are important. According to the results of survey, the mostly preferred maternity wear items were pants and one-piece dress. Korean customers for maternity wear usually pay more for the one-piece dress than other items and they also usually put on medium price pants and low-price blouse. Concerning to the purchase criteria, it may be said that design and movability, fit factors are the buying decision criteria of great weight for Korean pregnant women. Special function most desired was thermal insulation, followed by buffer action, electromagnetic shield and quickly water-absorbent and dry property. Preferred maternity wear design details were flat collar, slightly fitted waist and empire style, gather skirt, rubber band waist. Wear test was performed for two kinds of blouse (BL) and one-piece dress (OP), and threekinds of pants (PT), which have different design details respectively. According to the wear test for ready-to-wear maternity garments, the garment which considers well the characteristics of Korean pregnant women body shape earned much higher score no matter of brands or prices. Generally, high-priced national brands received an excellent evaluation in design aspect, but not satisfied with comfort to move.