• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.528-536
• /
• 1987

In a turbulent free shear flow, the large scale motion is characterized by the intermittent flow which arises from the interaction between the turbulent fluid and the irrotational fluid of the environment through the mean velocity gradient. This large scale motion causes a bulk convection whose effect is similar to the spatial diffusion process. In this paper, the total diffusion process is proposed to be approximated by weighted sum of the bulk convection due to the large scale motion and the usual gradient diffusion due to small scale motion. The diffusion term in conventional .kappa.-.epsilon. model requires on more equation of the intermittency transport equation. A production term of this equation means mass entrainment from the irrotational fluid to the turbulent one. In order to test the validity of the proposed model, a plane jet is predicted by this method. Numerical results of this model is found to yield better agreement with experiment than the standard .kappa.-.epsilon. model and Byggstoyl & Kollmann's model(1986). Present hybrid diffusion model requires further tests for the check of universality of model and for the model constant fix.

• Journal of the Korean Chemical Society
• /
• v.42 no.1
• /
• pp.22-27
• /
• 1998

Fluorescence quenching of coumarin 153 and coumarin 481 with N,N-dimethylaniline in various solvents was investigated. Quenching rate constants are related to diffusion-limited rate constants to some extent. It is noted that smaller discrepancy was observed between the diffusion-limited rate constant and the experimental quenching rate constant when the stick boundary condition rather than the slip boundary condition was applied for estimating the diffusion coefficients. In nonpolar solvent like cyclohexane fluorescence quenching is adequately explained by the diffusion controlled process within the experimental error, but in acetonitrile the quenching rate constant was estimated to be consistently smaller than the diffusion limited rate constant. This may suggest that fluorescence quenching of coumarin dyes be affected not only by the molecular diffusion but also by the intramoleccular process such as charge separation.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.4
• /
• pp.333-339
• /
• 1995

The reduction and diffusion process(R-D process) is an economical way to produce the functional materials which contain rare-earth elements and has been applied to the production of rare-earth magnet meterials($SmCo_5$, $Nd_{15}Fe_{77}B_8$), magneto-optical(MO) target materials and hydrogen storage alloy, etc. However, because of difficult to control of the final composition, the R-D process has not been applied to production of the 2-17 type rare earth permanent magnet materials which contain several elements. Therefore, this work was as a basic study for the production of the 2-17 type rare earth permanent materials with composition $Sm(Co_{0.72}Fe_{0.21}Cu_{0.05}Zr_{0.03})_{7.9}$ by the R-D process, the following were mainy examined ; the amount of metallic calcium as a reductant, homogenization condition of the alloy after the R-D reaction, masuring of magnetic properties of the sample after step aging. The sample prepared by the R-D process contained a little more oxygen than that prepared by the melting method, however, showed almost the same magnetic properties.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.1
• /
• pp.7-12
• /
• 2002

The gas diffusion electrodes as oxygen cathodes f3r the brine electrolysis process were investigated. The gas diffusion electrode consists of a reaction layer, a gas diffusion layer, and a current distributor. The reaction layer was made from hydrophilic carbon black, hydrophobic carbon black, PTFE(polyterafluoroethylene), and Ag catalyst loaded by the silver mirror reaction or impregnation method. The gas diffusion layer was made from hydrophobic carbon black and PTFE, and Ni mesh was used as the current distributor in the reaction layer. The result that the gas diffusion electrode $(10wt\%\;Ag\;catalyst\;and\;20wt\%\;binder)$ manufactured by applying impregnation method to the carbon black f3r reaction layer showed the better performance was obtained from experiments. From the half-cell test, the measured overpotential of this oxygen cathode was about 700mV, And through the electrolysis experiment under the condition of $80^{\circ}C,\;32wt\%$ NaOH, and $300mA/cm^2$, the electrolysis voltage of this electrode was about 2.2 V, The gas diffusion electrodes manufactured in the present research were capable of continuous operations for three months.

• Progress in Superconductivity and Cryogenics
• /
• v.24 no.4
• /
• pp.16-24
• /
• 2022

Applications of REBa₂Cu₃O_7-δ tapes require joints with a simple manufacturing process, low resistance and good mechanical properties. In the present study, we successfully developed a copper diffusion joint between Cu-stabilized REBa₂Cu₃O_7-δ tapes that meets the above requirements without solder simply by applying flux, heat and pressurization. After a 3 min thermocompression process at approximately 150 δ and 336 MPa in air, two tapes were directly connected between Cu stabilizers by copper diffusion, which was proven by microstructure analysis. The specific resistivity of the copper diffusion joint reached 5.8 nΩ·cm² (resistance of 0.4 nΩ for a 306 mm splicing length) at 77 K in the self-field. The axial tensile stress reached 200 N without critical current degradation. The results show promise for the preparation of copper diffusion joints to be used in coils, attached tapes, and wire/cable terminals.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1994.04a
• /
• pp.155-162
• /
• 1994

The drying shrinkage of concrete has a close relation to the water movement, Since the diffusion process of water in concrete is strongly dependent on the temperature and pore humidity, the process is highly nonlinear phenomena. It is shown that the analytical results of this study are in good agreement with experimental data in the literatures, and results calculated by BP-KX model. The internal stress caused by moisture distribution which was resulted from the diffusion process, was calculated quantitatively. The tensile stress which occurred in the drying outer zone mostly exceeded the tensile strength of concrete, and necessarily would result in crack formation.

• Journal of the Korean Ceramic Society
• /
• v.36 no.6
• /
• pp.583-589
• /
• 1999

In the fabrication of ceramic chip couples for high frequency application such as the mobile communication equipment the formation of electrode lines and Ag diffusion were investigated with heat treatment conditions for removing organic binders. The deformation and densification of the electrode line greatly depended on the binder burnout process due to the overlapped temperature zone near 400$^{\circ}C$ of the binder dissociation and the solid phase sintering of the silver electrode. Ag ions were diffused into the glass ceramic substrate. The Ag diffusion was led by the glassy phase containing Pb ions rather than by the crystalline phase containing Ca ions. The fact suggests that the Ag diffusion could be controlled by managing the composition of the glass ceramic substrate.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.301-304
• /
• 2015

With the experiment observation of single particle combustion, this model is built for the numerical analysis of the process. It's about the single coal particle combustion process under different conditions with reasonable assumptions. The model can express the mass, radius, density, temperature changing with different particle sizes, oxygen concentration and gas temperature. It also includes the flame sizes change in different condition and the diffusion of each species. The result shows the characters of the combustion.

• Proceedings of the Korea Society for Simulation Conference
• /
• 1999.10a
• /
• pp.186-191
• /
• 1999

The coagulation process of PAN (poly(acrylonitrile)) wet-spinning was modeled and simulated based on the numerical analysis of the coagulation of a viscous polymer solution by diffusional interchange with a bath. Experiments were performed with gelled solutions of PAN in nitric acid to determine the diffusion rate of solvent and nonsolvent (water) during the coagulation. The experimental data were analyzed by using equations of diffusion coefficient which are the function of the solvent concentrations of the coagulation bath and the filament. The concentration profile of solvent in moving filament was predicted by solving the diffusion model equation numerically. A simplex method was used in the computation of the parameters of the diffusion equations to minimize the difference between the numerical results and experimental data.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2001.10a
• /
• pp.342-345
• /
• 2001

Telecommunication services are distinctive in that their adoptions are influenced by network effect resulting in 'the late take-off Phenomenon' and the 'critical mass' problem. In this paper we examined, so called, 'the late take-off phenomenon' in the diffusion process of telecommunication services. We compared the parameters of the diffusion process of consumer durables with those of fax services in the US and Korea. By analyzing the parameters of a new diffusion model based on the threshold model proposed by Markus, We found that 'the late take-off phenomenon' resulted from the low heterogeneity of the threshold distribution for the potential adopters.