• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.11a
• /
• pp.67-73
• /
• 2001

To investigate the relationships of solder joint characteristics with solder composition and A:V ratio (solder volume per pad area), Sn-37Pb and Sn-4.0Ag-0.5Cu solder balls with 330, 400, 450 and $457{\mu}{\textrm}{m}$ size were reflowed on same substrate. Sn-37Pb and Sn-4.0Ag-0.5Cu was reflowed at $220^{\circ}C$ and $240^{\circ}C$ respectively by IR-type soldering machine. As a result of reflowed solder- ball diameter(D) and height(H) measurement, D/H was decreased with solder ball size increment in range of 330~450 ${\mu}{\textrm}{m}$. But, D/H was increased in the solder joint for 457 ${\mu}{\textrm}{m}$ size, it was caused possibly by decrement of solder ball height increment compared with solder volume increment. As a result of shear and pull test, joint strength with A:V ratio was high. Joint strength of Sn-4.0Ag-0.5Cu was higher than Sn-37Pb. However, Sn-37Pb had more stable solder joint of small standard deviation. A thick and clean scallop type Ni-Cu-Sn intermetallic compound layer was formed in high A:V ratio and Sn-4.0Ag-0.5Cu solder joint interface.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.1
• /
• pp.141-148
• /
• 2008

This study was conducted to evaluate the effect of PAC(Powder Activated Carbon) retention time on stable operation of high concentration powered activated carbon(HCPAC-MBR) in the treatment of secondary domestic wastewater. The pilot scale HCPAC-MBR system was operated at two different SRTs, 25 days and 100 days. The main drawback of HCPAC-MBR system was the rapid increase of trans-membrane pressure. The increase rate of trans-membrane pressure was proportional to SRT value at constant flux. This result seemed to be caused by reduced amount of EPS adsorbed on the PAC in the reactor by decreasing the SRT of the PAC. The particle size of the PAC was also influenced by SRT. The PAC size was decreased as SRT was increased. The change of particle size could be one reason for the change of trans-membrane pressure. The pore volume in the cake-layer formed on the membrane surface became to be increased by reducing SRT, because the cake-layer was highly composed of the PAC. Therefore, increased pore volume might play a role to reduce the trans-membrane pressure. The removal rate of E260 and TOC was also inversely proportional to SRT value.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.3
• /
• pp.97-105
• /
• 2012

The effects of pH, types of applied current, agitation method and time, additive on the amount of co-deposited $TiO_2$ particles in the matrix were investigated. The deposition rates increased with increasing pH values, while the volume fraction of $TiO_2$ particles and the size of agglomerated $TiO_2$ particles in the composite decreased. The volume fraction of $TiO_2$ particles in the composite decreased when pulsed current of 50% duty cycle was used. And the size of agglomerated $TiO_2$ particles in the nickel matrix of pulsed current was smaller than that of DC current specimen. The volume fraction of $TiO_2$ particles in the matrix decreased with longer time by air agitation, but in case of using magnetic bar, volume fraction in the same range of time was relatively constant. The volume fraction of the electrodeposited Ni-$TiO_2$ composite in the solution containing 0.01 M Dimethylamine borane (DMAB) increased slightly with increasing agitation time regardless of agitation methods. Thermal stability of the electrodeposited Ni-$TiO_2$ composite increased with lower pH at the temperature range of $200{\sim}800^{\circ}C$, and the results showed that the amount of co-deposited $TiO_2$ relies more on the deposition rate than zetapotential of $TiO_2$ particles.

• Journal of Korean Society for Atmospheric Environment
• /
• v.2 no.3
• /
• pp.27-33
• /
• 1986

Atmospheric particulate matter (A. P. M.) was collected and size-fractionated by an Andersen high-volume air sampler over 15 month period from Jan. 1985 to Feb. 1986 in Seoul. The concentration of chloride, nitrate and sulfate were extracted in an ultrasonic bath and were analyzed by ion chromatography. The annual arithmetical mean of A. P. M. was 128.54 $\mug/m^3$. The concentration of anions were 2.88 $\mug/m^3$ for chloride, 3.86$\mug/m^3$ for nitrate, and 25.44$\mug/m^3$ for sulfate. The content of A. P. M. was lowest in the particle size range 1.1 $\sim 3.3\mum$ and increased as the particle size increased or decreased. And the anions exhibited a seasonal variation in the isize distribution. The contents of anions were higher in winter than summer. Ther ratio of fine particles to the total particles defined by F/T for chloride, nitrate and sulfate. The F\ulcornerT of these anion generally decrease with increasing air temperature. This tendency was prevalent in the chloride and nitrate.

• YAKHAK HOEJI
• /
• v.30 no.6
• /
• pp.323-328
• /
• 1986

This paper describes on the distribution of polynuclear aromatic hydrocarbons (PAHs) in various size of atmospheric particulate matter (A.P.M.). A.P.M. in Seoul city were collected on guartz fiber filter according to particle size using an Andersen high volume air sampler from Feb. 1983 to March 1984. And 7 PAHs [benzo(a)pyrene, benzo(k)fluoranthene, benzo(ghi)perylene, benzo(e) pyrene, perylene, chrysene, and pyrene] were analyzed by high performance liquid chromatography. The concentration of A.P.M. showed spring-winter maxima and summer-autumn minia. The A.P.M. was lowest in the concentration at the 1.1~3.3$\mu\textrm{m}$ particulates, and the concentration increased as the particle size increased or decreased. But the concentrations of PAHs increased with the decrease in the particle size, and were predominant in winter. The correlations among the PAHs were high. And there fore, benzo(a)pyrene concentration could be considered as the representive of PAHs.

• Korean Journal of Materials Research
• /
• v.29 no.6
• /
• pp.349-355
• /
• 2019

This study deals with the microstructure and tensile properties of 600 MPa-grade seismic reinforced steel bars fabricated by a pilot plant. The steel bar specimens are composed of a fully ferrite-pearlite structure because they were air-cooled after hot-rolling. The volume fraction and interlamellar spacing of the pearlite and the ferrite grain size decrease from the center region to the surface region because the surface region is more rapidly cooled than the center region. The A steel bar specimenwith a relatively high carbon content generally has a higher pearlite volume fraction and interlamellar spacing of pearlite and a finer ferrite grain size because increasing the carbon content promotes the formation of pearlite. As a result, the A steel bar specimen has a higher hardness than the B steel bar in all the regions. The hardness shows a tendency to decrease from the center region to the surface region due to the decreased pearlite volume fraction. On the other hand, the tensile-to-yield strength ratio and the tensile strength of the A steel bar specimen are higher than those of the B steel bar with a relatively low carbon content because a higher pearlite volume fraction enhances work hardening. In addition, the B steel bar specimen has higher uniform and total elongations because a lower pearlite volume fraction facilitates plastic deformation caused by dislocation slip.

• The korean journal of orthodontics
• /
• v.25 no.2 s.49
• /
• pp.201-208
• /
• 1995

Recently, magnetic forces are considered as a method for more efficient tooth movement. The purpose of this study was to evaluate the effects of the changes of the magnetic volume on the magnetic forces. The universal testing machine and the electronic balance were used for the exact measurement of the force with constant air gap. While the magnet was kept same on one side, the magnetic volume of the other side was increased gradually in four manners. In the first group, the thickness was increased by adding same size of the magnets one after another while the thickness was increased by changing with a thicker magnet gradually in the second group. In the third group. the width was increased by adding same size of the magnets while the width was increased by changing with a wider magnet gradually in the last group. The results were as follows : 1. With the increase of the thickness, the magnetic force increased, while the magnetic force decreased with the increase of the width. 2. The magnetic force according to the change of the magnetic volume showed the distribution of the logarithmic function. 3. An originally thick magnet showed larger force than the added magnets although both of them had same volume.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.1
• /
• pp.27-34
• /
• 2000

This present study were investigated effect of Ni contents on the microstructure and strength characteristic in 9Cr ferritic heat-resistant steel added 1.7%W in place of Mo in order to restrain laves phase formation. The result obtained from this study are as follow. Volume fraction, number of particles per unite area and particle size of carbide decreased with increase of Ni contents. Other side, carbides of $M_{23}C_6$ type was mainly precipitated in this steel, but laves phases could not precipitated in spite of increasing of aging time. With increase of tempering temperature, hardness was increased, and maximum value was showed around 873k by secondary hardening due to precipitation of $W_2C$ type carbide and then, was decreased. Tensile and yield strength due to decrease precipitation amount of carbide and number of particles per unite area was decreased, but elongation and impact value was increased. In case of aged specimen after tempering than tempered specimen, strength was higher and elongation was lower due to increasing of precipitated amount of carbide and number of particles per unite area.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.1
• /
• pp.206-216
• /
• 1997

The purpose of this study was to determine the pore size distributions (PSDs) of polyester woven fabrics by using liquid extraction method. Three types of PSDs-percent PSD, PSD per unit area of sample and PSD per unit weight of sample-were evaluated. Plain, twill and satin polyester fabrics with various fabric counts were used as specimens. Results showed that the interyarn PSDs reflected the fabric characteristics such as the fabric count and the weave type and the intrayarn PSDs reflected the thread characteristics such as the number of fibers, the fiber diameter, the thread diameter and the thread twist. Of three types of PSDs, the PSD per unit area of sample best reflect fabric and thread characteritics. As the fabric count decreased, rc increased and interyarn pore volume increased. The PSDs were skewed to the small pore sizes and the pore volumes decreased in the order of plain> twill> satin. As the number of fibers, the fiber diameter and the thread twist decreased, the intrayarn pore volumes were increased.

• The Korean Journal of Ecology
• /
• v.26 no.4
• /
• pp.181-188
• /
• 2003

Frequencies of each size class, annual change of tuber state and above ground/belowground rate in sect. Pes-gallinaceua group of Corydalis (Fumariaceae) were studied to clarify spring ephemeral´s growth characteristics from 1999 to 2000 in Namhansansung area. Shoot grew from the tuber corresponding with soil thawing in the early growth season, and the deeper tuber was located in soil, the later shoot germinated. Shoot appeared in middle March and died early in May, and the period of total growth season was 45 days. Frequencies were 40% (in total dry weight) or 53% (in tuber´ dry weight) in the smallest size class, and 93% (in total dry weight) or 96% (in tuber´ dry weight) below medium size, therefore, almost all of plants were small. Specific gravity of tuber (SGT) gradually decreased from late growth season to the time that leaf unfolded in next year. At this time, the value of SGT was 0.14. Thereafter, SGT increased to 0.42 at withering time of aboveground part. During growth season, the SGT of flowering plants was lower than that of non-flowering plants. And SGT difference between flowering plants and non-flowering plants was significant at 1% level. In the late growth season, SGT decreased along the increase of tuber volume. The tuber volume roughly increased along the leaf area but there was no a conspicuous trend. Shoot/tuber rate had nothing to do with tuber volume. SGT decreased and leaf area increased along the tuber dry weight, and tendencies of increase or decrease were conspicuous. Therefore, the smaller the plants were, the larger organic matter accumulated in tuber during a growth season. Shoot/tuber rates were various along each plant.