• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.10a
• /
• pp.105-110
• /
• 2001

Autoclave curing using the vacuum bagging method is widely used for the manufacture of advanced composite prepreg airframe structures. Due to increasing use of advanced composites, specific techniques have been developed to repair damaged composite structures. In order to repair the damaged part, it is required that the damaged areas be removed, such as skin and/or honeycomb core, by utilizing the proper method and then repairing the area by laying up prepreg (and core) then curing under vacuum using the vacuum bagging materials. It shall be cured either in an oven or autoclave per the original specification requirements. Delamination can be observed in the sound areas during and/or after a couple times exposure to the elevated curing temperature due to the repeated repair condition. This study was conducted for checking the degree of degradation of properties of the cured parts and delamination between skin prepreg and honeycomb core. Specimens with glass honeycomb sandwich construction and glass/epoxy prepreg were prepared. The specimens were cured 1 to 5 times at $260^{circ}F$ in an autoclave and each additionally exposed 50, 100 and 150 hours in the $260^{circ}F$ oven. Each specimen was tested for tensile strength, compressive strength, flatwise tensile strength and interlaminar shear strength. To monitor the characteristics of the resin itself, the cured resin was tested using DMA and DSC. As a results, the decrease of Tg value were observed in the specific specimen which is exposed over 50 hrs at $260^{circ}F$. This means the change or degradative of resin properties is also related to the decrease of flatwise tensile properties. Accordingly, minimal exposure on the curing temperature is recommended for parts in order to prevent the delation and maintain the better condition.

• Journal of Integrative Natural Science
• /
• v.13 no.1
• /
• pp.34-40
• /
• 2020

This study aims to create a model for predicting the number of extinguishment manpower to put out forest fires by taking into account the climate, the situation, and the extent of the damage at the time of the forest fires. Past research has been approached to determine the cause of the forest fire or to predict the occurrence of a forest fire. How to deal with forest fires is also a very important part of how to deal with them, so predicting the number of extinguishment manpower is important. Therefore predicting the number of extinguishment manpower that have been put into the forest fire is something that can be presented as a new perspective. This study presents a model for predicting the number of extinguishment manpower inputs considering the scale of the damage with forest fire on a scale bigger than 0.1 ha as data based on the forest fire annual report(Korea Forest Service; KFS) from 2015 to 2018 using the moderated multiple regression analysis. As a result, weather factors and extinguished time considering the damage show that affect forest fire extinguishment manpower.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.2 no.2
• /
• pp.237-243
• /
• 1978

Dermatophytes such as Trichophyton mentagrophytes, Trichophyton rubrum and Epidermophyton floccosum are used in this study to confirm (a) The Dermatophytes could utilize the wool, cotton and nylon fiber as a nutrient source. (b) The degree of damage of fibers by the Dermatophytes growth. The results of the experiment are summarized as follows; 1. Dermatophytes could not utilize the wool, cotton and nylon fiber directly as a nutrient source without the exogenously applied nutrients. 2. It was presumed that Dermatophytes could utilize the knitted wool fabric as their nutrient source when nutrient was exogenously applied. since the knitted wool fabric was greatly damaged by T. mentagrophytes and T. rubrum growth. 3. The tensile strength of knitted wool fabric was significantly decreased by T. mentagrophytes and T. rubrum, but not by E. floccosum. However, the tensile strength of knitted nylon fabric was not particularly affected by the Dermatophytes. 4. The burst strength of knitted wool fabric was decreased by T. mentagrophytes ($77\%$). T. rubrum ($53\%$). and E. floccosum ($15\%$). Though the burst strength of knitted cotton fabric was decreased by Dermatophytes about $20\%$, that of knitted nylon fabric was not affected. 5. Observing the damaged wool fiber by scanning microscope, the inner part of wool fiber was permeated by T. mentagrophytes and T. rubrum.

• Earthquakes and Structures
• /
• v.18 no.6
• /
• pp.731-742
• /
• 2020

Due to incessant earthquakes, many historic South Nias traditional timber houses have been damaged while some still stand today. As Nias is part of an extremely active tectonic region and the buildings are getting older by day, it is essential that these unique houses are well maintained and functioning well. A post-earthquake condition assessment was conducted on 2 selected buildings; 'Building A' survived the seismic shakings while 'Building B' got severely damaged. The overall condition assessment of "Building A' was found out to be poor and the main structural members were not performing as intended. In 'Building B', the columns were not well anchored to the ground, no tie beams to tie the columns together, and eventually, the timber columns moved in various directions during the earthquake. The frequent earthquakes along with deterioration due to lack of proper maintenance program are responsible for the non-survival of the buildings. Thus, a process guideline for managing the maintenance of these buildings was proposed. This is necessary because managing the maintenance works could help to extend the life of the buildings and seek to avoid the need for potentially expensive and disruptive intervention works, which may damage the cultural significance of the buildings.

• Computers and Concrete
• /
• v.10 no.3
• /
• pp.277-294
• /
• 2012

The aim of the study is to determine the modal parameters of a prototype damaged arch dam by operational modal analysis (OMA) method for some damage scenarios. For this purpose, a prototype arch dam-reservoir-foundation model is constructed under laboratory conditions. Ambient vibration tests on the arch dam model are performed to identify the modal parameters such as natural frequency, mode shape and damping ratio. The tests are conducted for four test-case scenarios: an undamaged dam with empty reservoir, two different damaged dams with empty reservoirs, and a damaged dam with full reservoir. Loading simulating random impact effects is applied on the dam to crack. Cracks and fractures occurred at the middle of the upper part of the dams and distributed through the abutments. Sensitivity accelerometers are placed on the dams' crests to collect signals for measurements. Operational modal analysis software processes the signals collected from the ambient vibration tests, and enhanced frequency domain decomposition and stochastic subspace identification techniques are used to estimate modal parameters of the dams. The modal parameters are obtained to establish a basis for comparison of the results of two techniques for each damage case. Results show that approximately 35-40% difference exists between the natural frequencies obtained from Case 1 and Case 4. The natural frequencies of the dam considerably decrease with increasing cracks. However, observation shows that the filled reservoir slightly affected modal parameters of the dam after severe cracking. The mode shapes obtained are symmetrical and anti-symmetrical. Apparently, mode shapes in Case 1 represent the probable responses of arch dams more accurately. Also, damping ratio show an increase when cracking increases.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.25 no.6
• /
• pp.305-314
• /
• 2021

The Gyeongju and Pohang earthquakes caused damages to many cultural properties; particularly, stone pagoda structures were significantly damaged among masonry cultural properties. To preserve these structures, it is necessary to understand their dynamic behavior characteristics under earthquakes. Analyses on such areas as deformation, frequency, maximum acceleration, permanent displacement, sliding, and rocking have to be performed. Although many analytical studies have already been conducted, dynamic behavior studies based on experiments are insufficient. Therefore, this study analyzed dynamic behavior characteristics by performing a shaking table experiment on a three-story stone pagoda structure at the Cheollongsa temple site damaged by the Gyeongju earthquake. As a result of the experiment, the displacements of stylobates did not occur significantly, but the tower body parts rotated. In particular, the rotation of the 1F main body stone was relatively larger than that of the other chief body stones because the 1F main body stone is relatively more slender than the other parts. In addition, the decorative top was identified as the component most vulnerable to sliding. This study found that the 1F main body stone is vulnerable to rocking, and the parts located on the upper part are more vulnerable to sliding.

• Journal of Life Science
• /
• v.15 no.6 s.73
• /
• pp.889-894
• /
• 2005

This experiment was carried out to investigate the effects of simulated acid rain (SAR) in the shoot growth and internal structure of Arabidopsis thaliana. In the shoot growth, the plants treated with SAR (pH 3.0) for 15 days showed no morphological change compared to the control plants. Some change was observed in the internal structure of the stems: the epidermis and cortex tissues of the stems treated with SAR were partly damaged. The plants treated with SAR showed no noticeable difference compared to the control plants, but morphological changes were observed in the leaf. The leaves of the plants treated with SAR showed many white necrotic spots on the part of upper epidermis. A light microscopic examination of the leaves with necrotic spots showed that the upper epidermis was severely compressed with the damaged cuticle layer and the mesophyll cells were also damaged and compressed. However, noticeable structural change of vascular bundle cells was not observed.

• Journal of Korean Biological Nursing Science
• /
• v.15 no.4
• /
• pp.210-218
• /
• 2013

Purpose: The purpose of this study was to identify the characteristics and nursing activities of severe trauma patients regarding damaged body parts in Busan Regional Emergency Medical Center. Methods: A survey using a 'trauma patient information questionnaire and a list of nurse activities' was conducted with 133 patients over 15 points ISS on EMR from June 1, 2011 to May 31, 2012. The collected data were analyzed by the SPSS/WIN 12.0 program. Results: Almost all of the subjects were men, and the mean age was 48.8. The amount of road traffic accidents was 60.4%, and the mean RTS and ISS were 6.08, and 23.14 points. Nursing activities in common were airway management, assessment of LOC & GCS, and EKG monitoring. Most of head and neck trauma patients were cared for manasing using intracranial pressure: each patience had the following assessed: pupil size and light reflex, they were checked the leak of CSF, kept $30^{\circ}$ head elevation, and administered medications. Some of chest trauma patients were treated for chest tube and central venous catheter insertion. Partial abdominal trauma patients were administered analgesic and cared for using arterial pressure measurement. Part of the limbs and pelvis trauma patients were given a blood transfusion. Conclusion: Based on the results, the characteristics and nursing activities were specific according to the specific damaged body parts.

• Journal of Computational Design and Engineering
• /
• v.2 no.4
• /
• pp.261-267
• /
• 2015

Free-form blades are widely used in different industries, such as aero-engine and steam turbine. Blades that are damaged during service or have production deficiencies are usually replaced with new ones. This leads to the waste of expensive material and is not sustainable. However, material and costs can be saved by repairing of locally damaged blades or blades with localized production deficiencies. The blade needs to be further machined after welding process to reach the aerodynamic performance requirements. This paper outlines an adaptive location approach of repaired blade for model reconstruction and NC machining. Firstly, a mathematical model is established to describe the localization problem under constraints. Secondly, by solving the mathematical model, localization of repaired blade for NC machining can be obtained. Furthermore, a more flexible method based on the proposed mathematical model and the continuity of the deformation process is developed to realize a better localization. Thirdly, by rebuilding the model of the repaired blade and extracting repair error, optimized tool paths for NC machining is generated adaptively for each individual part. Finally, three examples are given to validate the proposed method.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.2 no.2
• /
• pp.13-19
• /
• 2011

This paper presents the stress distribution of the damaged butt joint of steel plate using CFRP laminates when the flange in tension zone of steel box girder is welded by butt welding. When CFRP sheets are patched on tension flange of steel-box girder, the stress distribution of a vertical and normal direction on damaged welding part is shown as parameters such as a variation of the thickness of adhesive, the overlap length with steel, and the modulus of elasticity of CFRP sheets. For the study, we wrote the computer program using the EAS(Enhanced assumed strain) finite element method for plane strain that has a very fast convergency and exact stress for distorted shape.