• Journal of the Korean Society of Safety
• /
• v.15 no.3
• /
• pp.7-13
• /
• 2000

Forming characteristics of tailored blank are mostly effected by the welding method. Recently, laser welding is widely used for the tailored blank. However, tensile and forming characteristics vary due to welding conditions such as welding speed, heat flux etc. The objective of this paper is to evaluate the effect of welding speed on the tensile and forming characteristics of laser welded tailored blank. For this purpose, tailored blank specimens with different welding speed were prepared and tensile tests were performed. Also forming tests such as LDH and OSU test, were performed to evaluate the effect of welding speed on the forming characteristics. Finally, forming limit diagrams were obtained for different welding speed.

• Journal of Power System Engineering
• /
• v.20 no.3
• /
• pp.51-56
• /
• 2016

In this study, the tensile tests and hardness tests were carried out for the joints characteristics in friction stir welds of Al 5052 alloy. Three way factorial design was applied to optimal welding conditions, whose control factors were shoulder diameter, rotation speed and welding speed of tool. From the results of this study, the optimum condition for maximum yield strength was predicted as the shoulder diameter of 15 mm, welding speed of 500mm/min and rotating speed of 1000 rpm. And the presumed optimal yield strength was estimated to be $167.36{\pm}7.82MPa$ with 99% reliability. In addition the increaser rotation speed of tool and the decreaser welding speed, the decreaser the hardness at welding part.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.5
• /
• pp.31-38
• /
• 2016

This study proposes an optimal design for a robotic welding system for a high-strength steel armor plate. In order to identify the welding defect parameters, we analyzed the 4M (man, machine, materials, method) characteristics diagram, as well as a cause and effect matrix, to improve the productivity and quality of welding defects. From these analyses, we designed optimal welding conditions and carried out welding tests -- such as mechanical testing and macro structure tests - with positive results. We determined that it was possible to obtain a quality similar to manual welding with our robotic welding system. In the future, we expect that the system will be used as inspiration for future welding system designs.

• Transactions of Materials Processing
• /
• v.9 no.6
• /
• pp.582-589
• /
• 2000

In recent automotive industry, vehicle weight can be reduced by one-step forming of tailored blanks welded with two or more sheets of metal blanks. Mash seam welding shows an overlap joint, a much wider welding area, and heat affected zone(HAZ) than a laser welding. This paper deals with the forming characteristics of mash seam welded tailored blanks. Mash seam welded blanks of same or different thickness combinations were prepared, and tensile, hardness, erichsen, and dome stretching tests were done.

• Journal of Welding and Joining
• /
• v.10 no.4
• /
• pp.240-249
• /
• 1992

The objective of this study is to investigate the characteristics of welded joints on the Zircaloy-4 resistance upset welding for HWR(Heavy Water reactor)fuel rods. To estimate the characteristics of welded joints, the various tests were performed on the test coupons systematically with a wide range of each welding parameters in terms of a tensile test, burst test, knoop hardness test and metallography. Major results obtained in this study are as follows: 1. The tube and machined with 120.deg. projection was the reliable weld joint design for the nuclear fuel rod end cap welding. 2. As the weld current and the amount of upset increased linearly with increasing welding main heat input, it could make an estimate of their variation in accordance with the phase shift control. 3. It was found that an increase in squeeze force has an effect on the upset contour of welded joint because the amount of upset were increased by the change of squeeze force.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.35-43
• /
• 2007

Laser welding of metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for metals with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the butt welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1325W of the laser power, and 1.4m/min of laser welding speed.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.6
• /
• pp.105-109
• /
• 2011

As is well appreciated, welding is the most important fundamental process in manufacturing marine structures. However, weld-induced deformation is inevitable because of the non-uniform distribution of temperature during welding. The deformation caused by welding is one of the principal obstacles in enhancing the productivity in the manufacturing procedure for marine structures. This should be much more seriously considered in the case of the thin blocks found in a ship with multi-deck structures. This paper is concerned with the deformation control of thin panel blocks by applying intermittent welding to fillet welding. In order to investigate the quantitative effect of the intermittent welding, a thermo elasto-plastic analysis was carried out with various welding pitches and plate thicknesses. Welding tests were also carried out to show the validity of the present thermo-elasto-plastic analysis. Numerical analysis results showed good agreement with those of the welding tests. As far as the present numerical results are concerned, it has been seen that a more than 50% reduction in angular distortion can be achieved by applying the intermittent welding because of the low heat input.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.155-157
• /
• 2007

The Friction spot dissimilar welding of galvanized steel/Al6061-T6 was performed to investigate the mechanical characteristics of the joints. The presence of thin film of aluminum oxide on the surface and melting of zinc in the coating, made substandard joint characteristics for dissimilar Friction spot joining(FSJ) performed with out removing the coating. Where as, for dissimilar FSJ of galvanized steel/Al6061-T6 after removing the coating, superior agitation and welding quality has been obtained for a configuration of galvanized steel as the upper plate and Al6061-T6 as lower plate. The results from tensile tests and microscopic examination for various combinations of the welding parameters have been presented.

• Journal of Welding and Joining
• /
• v.20 no.6
• /
• pp.78-78
• /
• 2002

Front-side members are structures with the greatest energy absorbing capability in a front-end collision of vehicles. This paper was performed to analyze initial collapse characteristics of spot welded hat and double hat-shaped section members, which are basic shape of side members, on the shift of flange weld pitches. The impact collapse tests were carried out by using home-made vertical air compression impact testing machine, and impact velocity of hat-shaped section members is 4.17m/sec and that of double hat-shaped section members is 6.54m/sec. In impact collapse tests, the collapsed length of hat-shaped section members was about 45mm and that of double hat-shaped section members was about 50mm. In consideration of these condition, axial static collapse tests(0.00017m/sec) of hat and double hat-shaped section members were carried out by using UTM which was limited displacement, about 50mm. As the experimental results, to obtain the best initial collapse characteristics, it is important that stiffness of vehicle members increases as section shapes change and the progressively folding mode induces by flange welding pitch.

• Journal of Welding and Joining
• /
• v.20 no.6
• /
• pp.802-808
• /
• 2002

Front-side members are structures with the greatest energy absorbing capability in a front-end collision of vehicles. This paper was performed to analyze initial collapse characteristics of spot welded hat and double hat-shaped section members, which are basic shape of side members, on the shift of flange weld pitches. The impact collapse tests were carried out by using home-made vertical air compression impact testing machine, and impact velocity of hat-shaped section members is 4.17m/sec and that of double hat-shaped section members is 6.54m/sec. In impact collapse tests, the collapsed length of hat-shaped section members was about 45mm and that of double hat-shaped section members was about 50mm. In consideration of these condition, axial static collapse tests(0.00017m/sec) of hat and double hat-shaped section members were carried out by using UTM which was limited displacement, about 50mm. As the experimental results, to obtain the best initial collapse characteristics, it is important that stiffness of vehicle members increases as section shapes change and the progressively folding mode induces by flange welding pitch.