• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.1225-1226
• /
• 2012

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국내학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.244-249
• /
• 1993

This paper proposes a method of automatic function test for parts mounted Printed Circuit Board. For this purpose, we designed a Data Acquisition Equipment, PC interface card and inspection software. The experiment was done for the coffee vending machine and its result was good.

• 한국초전도ㆍ저온공학회논문지
• /
• 제6권3호
• /
• pp.33-37
• /
• 2004

This paper presents the construction and test results of an HTS induction motor. End rings and short bars were made of HTS tapes, To increase the efficiency and starting torque, HTS tapes can be used as the rotor bars. Because large current is induced in the rotor circuit, HTS tapes quench and high starting torque can be obtained. As the speed of rotor builds up. HTS tapes which are used as short bars become superconducting state again. After the HTS tapes recover from quench, resistance of the rotor circuit is nearly zero. In that case, power loss in rotor circuit is eliminated. Stator of the conventional induction motor was used as the stator of the HTS motor. Rated capacity of the conventional motor was 0.75 kW. Performances of the HTS induction motor were compared with those of the conventional motor with same volume and specification. Test result showed that the speeds of the HTS induction motor were the same with synchronous speed up to 2.6 Nm and 1.788 rpm at 9.7 Nm. It guarantees the high efficiency of the HTS motor. Starting torque of the HTS motor was more than twice of the conventional motor.

• 전기학회논문지
• /
• 제62권8호
• /
• pp.1053-1058
• /
• 2013

Because of computational burden and complex topology of substation, a transmission overload relief using circuit-breaker switching was very complex and difficult. However, a on-line algorithm for reducing the overloads in transmission lines has made progress due to the advance of IT technology. This paper describes the methodology for alleviating the overloads in transmission lines by circuit-breaker switching. First, the severe contingency lists and substations were selected from the results of contingency analysis. Then the switch combinations are determined using circuit-breakers of the selected substation. The topology changes are limited to equipment outage, bus split, island split, bus merge and island merge. Finally, the fast screening and full analysis methods are used to analyze the overload in transmission lines. To verify the performance of the proposed methodology, we performed a comprehensive test for both test system and large-scale power systems. The results of these tests showed that the proposed methodology can accurately alleviate the overloads in transmission lines from online data and can be applied to on-line applications.

• 조명전기설비학회논문지
• /
• 제25권1호
• /
• pp.93-100
• /
• 2011

This paper presents a technical study for the first short stroke lightning current generator using a crowbar device. The so-called crowbar-technology is most common to make 10/350[${\mu}s$] impulse currents with high amplitude, and the lightning current generator with crowbar device has an economic advantage than the nominal RLC current generator. But both the operating efficiency and the operating reliability of crowbar spark gap are very important to design the current generator. So, the peaking circuit which consists of small capacitors and a spark gap is applied. And the multi-step coil for controlling the circuit constant at the different test conditions is used. The presented test facility is designed to perform impulse tests with amplitudes up to 50[kA] of 10/350[${\mu}s$].

• Journal of Welding and Joining
• /
• 제33권3호
• /
• pp.47-53
• /
• 2015

By the trends of electronic package to be more integrative, the fine Cu trace pitch of organic PCB is required to be a robust design. In this study, the short circuit failure mechanism of PCB with a Cl element under the Temperature humidity bias test ($85^{\circ}C$/85%RH/3.5V) was examined by micro-structural study. A focused ion beam (FIB) and an electron probe micro analysis (EPMA) were used to polish the cross sections to reveal details of the microstructure of the failure mode. It is found that $CuCl_x$ were formed and grown on Cu trace during the $170^{\circ}C$/3hrs and that $CuCl_x$ was decomposed into Cu dendrite and $Cl_2$ gas during the $85^{\circ}C$/85%RH/3.5V. It is suggested that Cu dendrites formed on Cu trace lead to a short circuit failure between a pair of Cu traces.

• Progress in Superconductivity
• /
• 제6권2호
• /
• pp.104-107
• /
• 2005

We have developed and tested an RSFQ 4-bit Arithmetic Logic Unit (ALU) based on half adder cells and de switches. ALU is a core element of a computer processor that performs arithmetic and logic operations on the operands in computer instruction words. The designed ALU had limited operation functions of OR, AND, XOR, and ADD. It had a pipeline structure. We have simulated the circuit by using Josephson circuit simulation tools in order to reduce the timing problem, and confirmed the correct operation of the designed ALU. We used simulation tools of $XIC^{TM},\;WRspice^{TM}$, and Julia. The fabricated 4-bit ALU circuit had a size of $\3000{\ cal}um{\times}1500{\cal}$, and the chip size was $5{\cal} mm{\times}5{\cal}mm$. The test speeds were 1000 kHz and 5 GHz. For high-speed test, we used an eye-diagram technique. Our 4-bit ALU operated correctly up to 5 GHz clock frequency. The chip was tested at the liquid-helium temperature.

• 한국통신학회논문지
• /
• 제27권1A호
• /
• pp.66-72
• /
• 2002

본 논문에서 구현한 GenJTAG은 기판 수준의 테스팅을 위한 정보와 BIST(Built-In Self Test)에 대한 정보를 입력으로 받아 verilog-HDL 코드로 기술된 경계 주사 회로를 자동 생성해 주는 설계 자동화 툴이다. 대부분이 상용 툴들은 생성된 회로를 게이트 수준의 회로로 제공하기 때문에 사용자가 선택적으로 사용할 수 있는 BIST 관련 명령어를 회로에 추가하기가 어려운데 반해, 본 논문에서 구현한 툴은 사용자가 정의한 정보에 의해 BIST 관련 명령어를 지원할 수 있는 behavioral 코드의 경계 주사 회로를 생성하여 준다. 또한 behavioral 코드를 제공함으로써 사용자에 의한 수정을 용이하도록 하였다.

• 임상간호연구
• /
• 제17권2호
• /
• pp.192-203
• /
• 2011

Purpose: The purpose of this study was to compare the body temperature (BT), blood pressure (BP) and shivering in patients undergoing operation under general anesthesia between the heated humidification circuit tube (HHCT) group and the non-HHCT group. Methods: Data were extracted from the participants' medical records from September 1st to December 30th, 2009. The HHCT group consisted of 50 cases who were applied with heated and humidified gas via a specially designed circuit under general anesthesia. The HHCT which was adjusted at $41^{\circ}C$ was applied from induction of general anesthesia to extubation. In comparison, the non-HHCT group consisted of 50 cases who were applied with gas through standard breathing circuit without heat and humidification. Collected data were analyzed by $x^2$ test, t-test and repeated measures ANOVA. Results: The BT and shivering were significantly different between two groups (p<.001). But the BP was was not signigicantly different between the HHCT group and the non-HHCT group. Conclusion: The application of heated and humidified gases to patients under general anesthesia was effective in preserving the body temperature and reducing the shivering.

• 드라이브 ㆍ 컨트롤
• /
• 제16권1호
• /
• pp.7-13
• /
• 2019

The objective of this study was to present a damped pneumatic suspension, a bike fork suspension, which can adapt itself to incoming road excitations is presented in this paper. It consists of a hydraulic damper and a pneumatic spring in parallel with a linear spring. The study also proposed a variable and switchable orifice, in the hydraulic damper, to select appropriate damping property. Hydraulic-pneumatic circuit model for the bike fork suspension was established based on AMESim, in order to predict its performance. In addition, elastic-damping characteristics of the fork such as spring constant and viscous damping coefficient were computed and compared, for validation, with those evaluated by experiment using the universal test machine. Through simulation analysis and test, it was established that the hydraulic-pneumatic circuit model is effective and practical for development of future MTB suspensions.