• Computers and Concrete
• /
• 제30권4호
• /
• pp.257-267
• /
• 2022

Two different types of rubber aggregates (40 mesh rubber powder and 1-4 mm rubber particles respectively) were devised to substitute fine aggregates at 10%, 15%, 20% and 30% by volume in self-compacting concrete to investigate their basic mechanical properties. The results show that with the increase of rubber content, the reduction of compressive strength, splitting tensile strength and static modulus of elasticity gradually increase, and energy dissipation performance gradually increase. The rubber addition significantly reduces brittleness and decelerates damaged process. Whilst, the effect of rubber particles is greater when they are finer. Considering the mechanical properties, the optimal rubber content is 10%. It is recommended that the rubber volume content in rubberized concrete (RC) should not be higher than 20%. In addition, a constitutive model under uniaxial compression was proposed basing on the strain equivalent principle of Lemaitre and the damage theory, which was in good agreement with the test curves.

• Composites Research
• /
• 제37권3호
• /
• pp.179-185
• /
• 2024

본 연구는 Representative Volume Element(RVE) 모델을 사용하여 초기 공극 결함이 있는 단방향 섬유강화 복합재의 횡방향 인장 강도 변화에 대해 정량적 평가 및 조사되었다. 초기 공극 결함을 표본오차와 신뢰 수준을 기준으로 적정 표본의 수가 계산된 후, 총 5000개의 초기 공극 결함이 있는 RVE 모델이 표본 집단으로 생성되었다. 표본 집단은 차원 축소법과 밀도 기반 군집 분석을 통해 유사도 분석이 진행되었으며 편향되지 않은 표본 집단임이 확인 및 검증되었다. 검증된 표본 분석 결과는 복합재 구조의 신뢰성 해석에 적용될 수 있게 Weibull 분포로 표현되었다.

• 한국재료학회지
• /
• 제30권1호
• /
• pp.8-13
• /
• 2020

Effect of heat treatment on microstructure and mechanical properties of an Fe-6.5Mn-0.08C medium-manganese steel is investigated in this study. Three kinds of medium-manganese steel specimens are fabricated by varying heat treatments of intermediate quenching (IQ), step quenching (SQ), and intercritical annealing (IA). Hardness and tensile tests are performed to examine the correlation of microstructure and mechanical properties for the Fe-6.5Mn-0.08C medium-manganese steel specimens. The IQ and SQ specimens have microstructures of martensite matrix with ferrite, whereas IA specimen exhibits microstructure of acicular ferrite matrix with martensite. The tensile test results show that the SQ specimen with martensite matrix has the highest yield strength and the lowest elongation. On the other hand, the SQ specimen has the highest hardness due to the relatively lower reduction of carbon content in martensite during intercritical annealing. According to the fractography of tensile tested specimens, the SQ specimen exhibits a dimple and quasi-cleavage fracture appearance while the IQ and IA specimens have fully ductile fracture appearance with fine-sized dimples caused by microvoid coalescence at ferrite and martensite interface.

• 한국분말재료학회지
• /
• 제28권2호
• /
• pp.134-142
• /
• 2021

In this study, AlSi10Mg powders with average diameters of 44 ㎛ are additively manufactured into bulk samples using a selective laser melting (SLM) process. Post-heat treatment to reduce residual stress in the as-synthesized sample is performed at different temperatures. From the results of a tensile test, as the heat-treatment temperature increases from 270 to 320℃, strength decreases while elongation significantly increases up to 13% at 320℃. The microstructures and tensile properties of the two heat-treated samples at 290 and 320℃, respectively, are characterized and compared to those of the as-synthesized samples. Interestingly, the Si-rich phases that network in the as-synthesized state are discontinuously separated, and the size of the particle-shaped Si phases becomes large and spherical as the heat-treatment temperature increases. Due to these morphological changes of Si-rich phases, the reduction in tensile strengths and increase in elongations, respectively, can be obtained by the post-heat treatment process. These results provide fundamental information for the practical applications of AlSi10Mg parts fabricated by SLM.

• 한국주조공학회지
• /
• 제10권1호
• /
• pp.57-63
• /
• 1990

Continuous casting of the $Al-CuAl_2$ eutectic composite was carried out by the upward continuous casting process. The morphology of the eutectic growth and the stability of solid-liquid interface were investigated under various growth conditions. It was possible to get the planar solid-liquid interface at the condition of $G_L/R$＝$3.6{\times}10^3^{\circ}Csec/mm^2$. And the colony structures were formed at the conditions of $G_L/R$ < $R=0.33{\times}10^3^{\circ}Csec/mm^2$. The inter-lamellar spacing of $Al-CuAl_2$ eutectic composite was decreased with the increase of pulling speed. The reduction of inter-lamellar spacing & value of $G_L/R$ caused the increase of ultimate tensile strength and Rockwell hardness in $Al-CuAl_2$ eutectic composite.

• 한국분말재료학회지
• /
• 제16권6호
• /
• pp.438-441
• /
• 2009

Mg-Cu composites were successively fabricated using a combination of rapid solidification and extrusion processes. In addition, the microstructural variation of the composite was investigated by performing the extrusion repeatedly. It resulted that the composite formed an uniform and dense structure by the extrusion, and the microstructure became fine as the extrusion conducted repeatedly. The microstructural variation was known to be dependent on the number of extrusion and the area reduction ratio. The tensile strength was also measured as a function of the microstructural variation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.163-167
• /
• 2003

The large deformation at cryogenic temperature would be one of the effective methods to produce large bulk UFG materials. The effects of annealing temperature 150∼300$^{\circ}C$, on microstructure and mechanical properties of the sheets received 85% reduction at cryogenic temperature were investigated. In comparison with those at room temperature. Annealing of 5083 Al alloy deformed 85%, at 200$^{\circ}C$ for an hour, results in the considerable increase of tensile elongation without the great loss of strength and the occurrence of equiaxed grains less than 300nm in diameter.

• 한국염색가공학회지
• /
• 제13권6호
• /
• pp.381-390
• /
• 2001

The optimum carrier concentrations were obtained by the maxmium exhaustion ratios of polyester fabrics at 8$0^{\circ}C$ . The optimum concentrations of methylsalicylate, acetophenone, anisole, propiophenone, 2-ethyl hexyl alcohol, ethylene glycol and propylene glycol were $3g/\ell,\;12g/\ell,\;7g/\ell,\;5g/\ell,\;3g/\ell,\;35g/\ell,\;and\;40g/\ell$, respectively Azo, anthraquinone, and quinoline disperse dyes were quite stable up to PH 10.3, but nitro disperse dye were severely hydrolyzed in alkaline dyeing. The tensile strength decreased with increasing dyebath pH because the polyester fabrics were easily decomposed by alkali. The reduction cleaning could be canceled in alkaline dyeing because the carriers were solved by alkali during dyeing.

• 한국염색가공학회지
• /
• 제13권6호
• /
• pp.23-23
• /
• 2001

The optimum carrier concentrations were obtained by the maxmium exhaustion ratios of polyester fabrics at 80℃. The optimum concentrations of methylsalicylate, acetophenone, anisole, propiophenone, 2-ethyl hexyl alcohol, ethylene glycol and propylene glycol were 3g/ℓ, 12g/ℓ, 7g/ℓ, 5g/ℓ, 3g/ℓ, 35g/ℓ, and 40g/ℓ, respectively. Azo, anthraquinone, and quinoline disperse dyes were quite stable up to pH 10.3, but nitro disperse dye were severely hydrolyzed in alkaline dyeing. The tensile strength decreased with increasing dyebath pH because the polyester fabrics were easily decomposed by alkali. The reduction cleaning could be canceled in alkaline dyeing because the carriers were solved by alkali during dyeing.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.903-908
• /
• 2002

The production of waste glasses has been increased with the development of industry. The utilization of waste glass for concrete can cause the concrete to be cracked and to be weakened due to an expansion by alkali-silica reaction(ASR). When used the fibers with waste glass, there is an effect on reduction of expansion and strength loss due to ASR between the alkali in the cement paste and the silica in the waste glass. In this study, we conducted basic experimental research to analyze the possibilities of recycling of amber waste glass as fine aggregates for steel fiber reinforced concrete. Test results of fresh concrete. slump is decreased because grain shape is angular and air content is increased due to involving small size particles so much in waste glasses. Also. tensile and flexural strengths increased as the content of steel fibers increased. In conclusion, the content of waste glass below 40% is reasonable and usage of pertinent admixture is necessary to obtain workability or air content.