• 한국지하수토양환경학회지:지하수토양환경
• /
• 제6권1호
• /
• pp.53-62
• /
• 2001

표면결함이 고밀도 폴리에틸렌 지오멤브레인의 열적 안정성과 응력균열저항성에 미치는 영향을 온도와 표면 결함 부여조건을 달리한 환경조건에서 역학적 특성, 화학저항성 및 피로시간을 측정하여, 조사하였다. 특별 고안된 장치를 사용하여 인위적으로 지오멤브레인 표면에 결함을 부여하였다. 표면결함은 표면결함 유도매체의 전단속도 100mm/min에서 표면결함 유도매체의 크기가 작을수록, 표면결함 부여횟수가 커질수록 증가하였다. 또한 이 조건에서 인장강도는 감소하였지만 인장신도는 증가하였다. 표면결함 부여조건이 같을 경우 고온으로 갈수록 그리고 침지시간이 길어질수록 인장강도는 감소되고 인장신도는 증가하여 표면결함이 부여된 지오멤브레인의 화학저항성은 저하되었다. 끝으로 응력균열저항성 시험 결과 온도가 높아질수록 표면결함이 부여된 지오멤브레인의 피로시간은 단시간 영역으로 이동되었다.

• 한국조경학회지
• /
• 제27권5호
• /
• pp.80-93
• /
• 2000

This study measured the shearing resistance of the roots of the Pinus Koraiensis by the tensile strength gained through their individual tensile test for the Root Reinforcement Model. On the basis of the shearing resistance value calculated through such a process the factor of safety(Fs) was comparatively presented by using the simplified Janbu Method in PCSTABL5M, the slop-analyzing software which had been developed in Purdue University of the U.S.A according to the shape of a slope and the type of soil. The results to have measured a stress and the factor of safety(Fs) by experiment are as follows. 1) The mean root diameter of the Pinus Koraiensis used for this experiment was 2.483mm and the mean tensile stress was calculated as 422.846(kgf/$\textrm{cm}^2$). In the strain ratio of material and the elastic modulus was measured 7.8%, 9,291.92(kgf/$\textrm{cm}^2$). 2) The shearing strength including the resistance of soil and root is expressed as Rt=C+Cr+$\sigma$.tan . ΔCr(kg/$\textrm{cm}^2$) of the shearing resistance calculated by estimating the areal ratio of roots at 10 is 0.253(kgf/$\textrm{cm}^2$). 3) As the result of making an analysis of the natural slope stability by the soil parameter, the factor of safety(Fs) was calculated at 1.795 in CL, and the stability analysis of the root reinforcement slope, Fs was calculated at 1.952. However, since a precise analysis of the controlled factors of the slope analyses are demanded for more accurate dynamic analyses, the future demands a study on this.

• KCI Concrete Journal
• /
• 제13권2호
• /
• pp.42-48
• /
• 2001

The bend resistance of coated reinforcing bar is greatly influenced by both the adhesion strength between bar and coating materials, and the followed transformation of coating material as bars bend. Especially, tearing state or partial microscopic cracks are predicted on the inside and outside of bending angle, because tensile strength and elongation of polymer film are very different according to types of polymer dispersions in bar coating, and these damaged parts are rapidly corroded by penetration of corrosive factors. In this study, polymer cement slurry coated reinforcing bars with various polymer dispersions are prepared by following combined conditions, polymer-cement ratio of 50% and 100%, coating thickness of 250$\mu$m and 450$\mu$m, coating number, curing age of 3, 7, 14 and 28days. Then the specimens are tested for working life and bend resistance at bending angles $90^{\circ}$, $135^{\circ}$and $180^{\circ}$ to observe the microscopic damage effect as the bars bend. Also, epoxy-coated reinforcing bars for control experiment were used with 250$\mu$m of coating thickness. The tensile strength for polymer films is performed. From the test results, the working life of the polymer cement slurry is within 90 seconds. Among four types of polymer dispersion, polymer cement slurry coated reinforcing bar using St/BA-1 emulsion has the excellent bend resistance, which is remarkably improved than that of epoxy-coated reinforcing bar. And the bend resistance is more related to elongation than tensile strength of polymer film. Polymer cement slurry with a polymer-cement ratio of 100%, a coating thickness of $450\mu$m and one coating using St/BA emulsion is selected as a most suitable coating material for coated reinforcing bar.

• Journal of the Korean Wood Science and Technology
• /
• 제27권1호
• /
• pp.88-104
• /
• 1999

본 시험은 외발 뜨기 한지와 쌍발 뜨기 한지를 구분하고 각각의 물성 차이 중 특히 4가지 강도에 대해 상대적 우위와 가로 세로 강도의 차이를 파악했다. 그 결과, 섬유 배향성을 특별히 고려하지 않은 외발 뜨기는 쌍발 뜨기와 비교해 가로, 세로 강도 차이가 다소 적다는 것 외에 특별히 뛰어난 점이 없다는 것을 알 수 있었다. 외발 뜨기 한지가 질기다고 느껴지는 것은 좋은 원료와 토착식 제법으로 여러 장(2~8장) 겹쳐서 절대적인 강도를 향상시켰기 때문이며 상대적인 강도인 지수비교에서는 큰 차이가 없었다. 또한 부가적으로 도침의 효과를 파악할 수 있었다. 도침은 내절도를 두드러지게 향상시켰으며 인열지수(인열강도)를 뺀 열단장과 파열지수(파열강도)를 높이는 역학을 했다. 특히 열단장(인장강도)의 향상을 가져왔다. 그리고 토착식 제법의 외발 뜨기는 여러 겹을 겹칠수록 인열지수가 증가(다른 강도에 비교해 상대적인 증가임)하는 경향을 보였다. 그러므로 도침과 토착식 한지는 서로 부족한 강도를 훌륭히 보완하는 역할을 했음을 알 수 있었다. 따라서 섬유 배향성을 고려하여 초지하고 도침을 실시해야 외발 뜨기 고유의 강도적 특징을 살릴 수가 있음을 알 수 있었다. 그리고 오늘날에 토착 외발 뜨기 방식으로 제조된 전통 한지들은 전체적인 강도면에서 토착 한지류와 비슷했으며 2겹지의 경우엔 가로 세로 강도차이도 토착한지 수준이었다. 그러나 강도들간의 우열 특성에서는 인열강도가 특히 낮았던 쌍발 뜨기 한지와 전체적으로 고른 강도를 보인 토착 외발 뜨기 한지의 중간에 위치하여 개선의 여지를 찾을 수 있었다.

• 소성∙가공
• /
• 제22권5호
• /
• pp.264-268
• /
• 2013

Aluminum clad sheets for brazing materials in the automotive heat exchangers are required to exhibit both high strength and excellent erosion resistance. In this study, the effects of microstructural changes on the property of clad sheets due to thermomechanical treatment were investigated. The clad sheets were fabricated by roll bonding of twin-roll-cast AA3527 and AA4343 alloys followed by cold rolling down to a thickness of 0.22mm. Partial or full annealing was conducted at the final thickness in order to improved the erosion resistance while keeping the proper strength. Since full annealing was achieved for a temperature of $400^{\circ}C$, annealing treatments were performed at 360, 380, and $400^{\circ}C$, respectively. The tensile strength of 3527/4343 clad material was found to be inversely proportional to the annealing temperature before the brazing heat treatment. After this latter treatment, however, the tensile strength of the clad material was about 195~200MPa regardless of the annealing temperature. The erosion depth ratio of the clad annealed at $400^{\circ}C$ was 8.8% (the lowest), while that of the clad annealed at $380^{\circ}C$ was 17% (the highest). The effect of annealing temperature on the tensile and erosion properties of 3527/4343 aluminum clad sheets was elucidated by means of microstructural analyses.

• Journal of Welding and Joining
• /
• 제24권6호
• /
• pp.39-43
• /
• 2006

A ferritic stainless steel, STS430, and a galvanized steel for case and frame of electronic goods are welded by resistance spot welding and resistance projection welding methods. In this study, resistance spot welding has been performed to investigate the weldability of dissimilar materials such as a ferritic stainless steel and a galvanized steel. Tensile load of the spot weld without heat treatment was 196 kN and brittle fracture occurred at interface between STS430 and nugget due to the high hardness, 380 Hv, in nugget. It was found that the hardness of as-welded nugget increased with higher cooling rate during resistance spot welding by comparing with GTA weld of same materials. Heat treatment by applying second current made nugget softened. Tensile load of heat treated weld increased and reached to 303 kN and fracture occurred at base metal, a galvanized steel.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.42-62
• /
• 1997

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. Recently, automobile industries are trying to replace partly steel sheets with aluminum alloy sheets. Among currently produced aluminum alloys, Al alloy sheets of Al-Mg-Si(6000 series) are being tested. Especially, 6000 series are the most probable substitute in view of strength and weldability. In this paper, an attempt was made to apply resistance spot welding to joining of dissimilar sheet metals (KS6383+SCPZn or KS6383+SHCP). An effort was made to balance heating rate in the Al alloy with that in the steel sheets by increasing electrode tip diameter. Although resistance spot welding of Al alloy sheet and sheet metals does not produce desirable nugget, it proved to have reasonable strength if optimal weld condition is found by tensile-shear strength and fatigue life test. Since spot weld joints in automobile are always experiencing repeated load, spot welding methodology proposed in this paper is found to be not suitable to automobile body manufacturing.

• Elastomers and Composites
• /
• 제41권2호
• /
• pp.79-87
• /
• 2006

내소음성과 내균열성을 가진 고무재료의 개발을 목적으로 NBR에 oleamide와 아라미드를 첨가하여 함량에 따른 가황특성, 물리적 성질, 내열성, 내유성, 내마모성, 내균열성 및 내소음성을 조사하였다. 가황특성과 Mooney 점도를 측정한 결과, 미가황고무의 가황특성은 oleamide의 양이 증가할수록 torque가 감소하였다. oleamide의 함량이 3 phr까지 증가함에 따라 경도 및 모듈러스 값은 조금씩 감소하였고 신장률은 감소하는 경향을 나타내었으며 인장강도는 거의 변화가 없었다. 내열성 시험(70시간, $120^{\circ}C$) 및 내유성 시험(70시간, $40^{\circ}C$)을 수행한 결과. 인장강도와 신장률이 모두 감소하였으며, TGA/DSC 분석 결과 첨가제에 따른 배합고무재료의 열적특성은 변화가 없었다. 기본물성, 내마모성, 내소음성 및 내균열성을 종합한 결과, NBR 227001 고무재료에서 내마모성과 내소음성에 대한 oleamide의 최적배합비는 3 phr였으며, 내균열성에 대한 아라미드의 최적배합비는 1 phr로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 토목섬유 학술발표회 논문집
• /
• pp.39-55
• /
• 1999

Geotextile composites to improve the weather ability were composed of recycled polyester geotextile with carbon black as ultraviolet stabilizer and polypropylene geotextile by needle-punching method, and evaluated physical properties, ultraviolet resistance and chemical stability. Retention ratio of tensile properties of non woven polypropylene geotextiles were decreased about 50% by the exposed condition with ultraviolet but those of geotextile composites were slightly decreased than polypropylene geotextiles. Geotextile composites which have larger weights of polyester geotextile were more stable against ultraviolet. For chemical stability, the changes of tensile properties of geotextile composites were in the range of -20~＋10% at the various chemical conditions.

• Elastomers and Composites
• /
• 제52권1호
• /
• pp.59-68
• /
• 2017

The effect on the hydrolysis resistance properties by the addition of maleic anhydride grafted EMDM (MA-g-EPDM) and PP (MA-g-PP) to a PA66/GF composite was investigated with respect to the mechanical properties, thermal properties, and morphology. The degree of hydrolysis of the PA66/GF composite was measured using py-GC/MS analysis. When compared to the PA66/GFcomposite in MEG/water solution, the composites where MA-g-EPDM and MA-g-PP were added to PA66/GF showed a higher degree of hydrolysis resistance, impact strength, and thermal properties, whereas their tensile strength, tensile modulus, flexural strength and flexural modulus decreased. As immersion time in the solution increases, the rate of tensile strength drop of the MA-g-PP added composite appeared lower than that of the PA66/MA-g-EPDM/GF and PA66/GF composites. The py-GC/MS analysis confirmed the formation of PA66 hydrolysis reaction by products such as carboxylic acid and alkylamine with increasing immersion time.