• 콘크리트학회논문집
• /
• 제24권2호
• /
• pp.205-214
• /
• 2012

균열폭은 콘크리트 구조물의 사용성을 평가하는 측면에서는 매우 중요하다. 균열폭을 일정값 이하로 유지할 수 있다면 낮은 투수성을 유지할 수 있으므로 콘크리트의 피복만으로도 염소이온에 의한 부식을 방지할 수 있다. 따라서 내구적인 구조물을 설계하기 위해서는 인장 균열에 대한 충분한 정보가 필요하다. 그러나 균열폭을 정확하게 계측하는 데는 몇 가지 어려움이 있다. 먼저, 균열의 생성 위치를 미리 알기 어렵다. 또한 변형률 게이지 등 탄성영역에서 사용되는 게이지는 사용할 수 없다. 이러한 문제를 극복하기 위해서 화상상관기법 및 고해상도 CCD를 이용한 균열 및 변위계측 시스템을 개발하였다. 이를 통해서 임의의 위치에 생성되는 인장균열폭을 측정하는 방법을 제시하였다. 변위계측 정밀도 검증을 실시한 결과 평균오차는 0.069 픽셀, 표준편차는 0.050 픽셀이었다. UHPC를 이용하여 직접인장 실험을 수행하였다. 노치 구역과 비노치 구역에서 각각 균열을 측정하는 방법을 제시하고, 하중단계에 따라서 클립인 게이지의 결과와 비교하여 설명하였다. 시편의 전면에서 변위벡터를 구성하고, 등변위도 및 변형률도를 작성하였다. 다양한 실험에 적용할 수 있는 범용의 기법이기 때문에 임의의 균열폭 혹은 전면변위 측정 분야에서 많이 활용될 수 있을 것이다.

• 대한기계학회논문집A
• /
• 제30권7호
• /
• pp.826-832
• /
• 2006

For the improvement of safety and endurance in welded steel structure, it is needed to consider welding residual stress distribution and rolling directional characteristics of materials. In this study, it was investigated experimentally about characteristics of fatigue crack propagation according to welding residual stress and rolling in FCAW(flux cored arc welding) butt-jointed steel plates. SS400 steel plates of 3mm thickness were selected and tested for this study. When the angles between tensile loading direction and rolling direction in welded materials are increased from $0^{\circ}\;to\;90^{\circ}$, their fatigue crack propagation rates are increased. These results are same as predicted increments of fatigue crack propagation rate when stress ratio is increased from 0 to 0.5. When the angles of rolling direction and welding direction to tensile loading direction are $0^{\circ}\;and\;90^{\circ}$ respectively, fatigue crack propagation rate in welded material is lowest.

• 대한기계학회논문집A
• /
• 제20권4호
• /
• pp.1301-1308
• /
• 1996

In order to save the energy and protect the environment, it were studied about ecomaterials with the developed countries as central figure. In the Metal Matrix Composites(MMCs), this trends appeared the development of the MMCs which had excellent mechanical properties in spite of the low volume fraction of reinforcement. Therefore, in this study, fatigue crack growth test, tensile and hardness test were conducted in order to investigate the mechanical and fatigue properties of 5 %, and 10 % $SiC_{p}$/Al composites. As the results, in the tensile and hardness test, tensile strength and hardness increased but fatigue crack growth rate decreased with $SiC_{p}$/Al volume fraction. And in the view of fatigue failured surface through the SEM, fatigue crack initiated around the SiC particle and in low $\Delta{K}$ regions, fatigue creck detoured the SiC particle but crack propagated through the SiC particle in the high $\DeltaK$ regions.

• 콘크리트학회논문집
• /
• 제14권2호
• /
• pp.239-248
• /
• 2002

철근 콘크리트 면부재의 주기거동을 나타내기 위하여 소성모델과 손상모델의 통합구성모델을 개발하였다. 인장-압축을 받는 콘크리트의 응력은 개념적으로 콘크리트의 스트럿 작용에 의한 압축응력과 인장균열에 의한 인장응력의 합으로 정의하였다. 인장균열의 비등방손상에 의하여 영향을 받는 압축파괴의 등방손상을 나타내기 위하여 다중파괴기준을 갖는 소성모델을 사용하였으며, 다중균열 방향에서 인장응력-변형률 관계를 나타내기 위하여 다중고정균열손상모델과 인장균열의 소성유동모델의 개념을 사용하였다. 이러한 통합모델은 주기 인장-압축 상태의 철근 콘크리트의 거동측성, 즉 다중 인장균열 방향, 점진적으로 회전하는 균열 손상, 콘크리트의 압축파괴를 나타낼 수 있다. 제안된 구성모델은 유한요소해석에 적용되었으며, 주기하중을 받는 철근 콘크리트 전단패널 및 전단벽에 대한 기존의 실험결과들과의 비교를 통해 검증되었다.

• Steel and Composite Structures
• /
• 제17권2호
• /
• pp.145-157
• /
• 2014

This study aimed to investigate the fatigue crack growth behavior of a kind of fiber metal laminates (FML) under four different stress levels. The FML specimen consists of three 2024-T3 aluminum alloy sheets and two layers of glass/epoxy composite lamina. Tensile-tensile cyclic fatigue tests were conducted on centrally notched specimen at four stress levels with various maximum values. A digital camera system was used to take photos of the propagating cracks on both sides of the specimens. Image processing software was adopted to accurately measure the length of the cracks on each photo. The test results show that: (1) a-N and da/dN-a curves of FML specimens can be divided into transient crack growth segment, steady state crack growth segment and accelerated crack growth segment; (2) compared to 2024-T3 aluminum alloy, the fatigue properties of FML are much better; (3) da/dN-${\Delta}K$ curves of FML specimens can be divided into fatigue crack growth rate decrease segment and fatigue crack growth rate increase segment; (3) the maximum stress level has a large influence on a-N, da/dN-a and da/dN-${\Delta}K$ curves of FML specimens; (4) the fatigue crack growth rate da/dN presents a nonlinear accelerated increasing trend to the maximum stress level; (5) the maximum stress level has an almost linear relationship with the stress intensity factor ${\Delta}K$.

• 대한기계학회논문집A
• /
• 제23권6호
• /
• pp.943-951
• /
• 1999

The welded structure unnecessarily remains residual stress due to the very high heating of local region and lastly cooling. The residual stress sometimes causes fracture initiation of welded structures. In this paper, distribution and magnitude of tensile and compressive residual stresses in the TIG(Tungsten Inert Gas) welded aluminum alloy such as Al5083-H112 are measured by using the hole-drilling method. Furthermore, the effects of residual stresses in the TIG welded aluminum CCT(Center Crack Tension) and SEN(Single Edge Notched) Specimens on the fatigue crack propagation behavior are analyzed. The fatigue cracks initiated at residual stresses region are influnced by tensile and compressive residual stresses. However, the effects are found to be released fast for both cases according to the cyclic loads and extension of crack length.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.9-15
• /
• 2001

In the case of a crack propagation, a portion of the work of inelastic deformation near the crack tip is dissipated as heat. In order to understand the thermal effect on fracture toughness, tensile test was carried out using thermocouples to monitor the variation of temperature with SA516 Gr70. The experimental results show that the temperature of specimen was increased $3.6^{\circ}C$ at static load condition. And the thermal effect was investigated connected with the steady-state stress in the vicinity of a crack propagation in the elastic-plastic C-T specimen theoretically. And fracture toughness, the energy to make crack surfaces, presented correctively. The fracture toughness with considering heat at the blunting of the crack tip ws lower about 19.3% than that of ignoring heat. So, it is resonable to apply the fracture toughness with considering thermal energy and it would be good explanation for constraint effect depending on the configuration in the presence of excessive plasticity.

• 한국안전학회지
• /
• 제16권2호
• /
• pp.1-6
• /
• 2001

In the case of a crack propagation a portion of the work of inelastic deformation near the crack tip is dissipated as heat. In order to understand the thermal effect on fracture toughness, tensile tests were carried out using thermocouples to monitor the variation of temperature. The experimental results show that the temperature of specimen was increased $5.4^{\circ}C$ at static load condition. And the thermal effect is investigated connected with the steady-state stress in the vicinity of a crack propagation in the elastic-plastic C-T specimen theoretically. And fracture toughness, the energy to make crack surfaces, presented correctively. The fracture toughness with considering heat at the blunting of the crack tip is lower about 16.9％ than that of ignoring heat. So, it is resonable to apply the fracture toughness with considering thermal energy and it would be good explanation for constraint effect depending on the configuration in the presence of excessive plasticity.

• Journal of Welding and Joining
• /
• 제13권2호
• /
• pp.60-67
• /
• 1995

The factors affecting on the fatigue strength of spot_welded specimens have been studied. The influence of initial overloads on the fatigue life of spot_welded tensile_shear specimens is investigated by considering fatigue crack initiation and crack propagation. The change of strain range and the influence of initial overload are correlated on the basis ol strain results. The results of this study are as follows. l) The initial absolute strain range decreased with initial overloads increase, and absolute strain range decreased before transformation of waveform of strain, but increased after transformation of waveform of strain. 2) In case of subsequent point of inflection of offset strain, the increment of this strain decreased with initial overload increase. 3) As initial overloads increase, the deformation behavior of spot welded parts is restricted after overloading.

• 한국강구조학회 논문집
• /
• 제9권4호통권33호
• /
• pp.515-521
• /
• 1997

마그네슘 금속 복합재의 열처리 및 섬유 강화재 방향에 따른 효과를 파악하기 위하여 인장강도 및 피로해석이 연구되었다. TEM 관측에 따라 시편은 섬유 강화재와 마그네슘 복합기지 사이의 시효 열처리된 변형된 계면이다. 인장실험 결과로부터 시효 처리된 시편의 극한 인장강도는 주조상태의 시편보다 시효 처리시 화학반응에 의한 섬유 강화재-기지간의 접합강도 약화로 감소하였다. 피로균열 거동실험은 균열거동 방향이 섬유 강화재 방향과 수직인 시편과 균열거동 방향이 섬유 강화재 방향과 평행한 시편을 실험하였다. 피로균열 거동해석을 비교해보면 섬유 강화재와 하중방향이 수직인 시효처리된 시편의 경우가 주조상태의 시편보다 피로균열 거동에 더 크게 저항하였다. 반대로 섬유 강화재 방향에 평행한 주조상태의 시편은 섬유 강화재 방향에 평행한 시효처리된 시편보다 피로 균열거동에 더 크게 저항함을 알 수 있었다.