• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1552-1554
• /
• 1997

In this paper, thin films of PI were fabricated VDPM of dry processes which are easy to control the film's thickness and hard to pollute due to volatile solvents. From FT-IR, PAA thin films fabricated by VDP were changed to PI thin films by thermal curing. From AFM and ellipsometer experimental, the higher curing temperature is, the films thickness decreases and reflectance increases. Therefore, PI could be fabricated stable by increasing curing temperature.

• Journal of ILASS-Korea
• /
• v.8 no.4
• /
• pp.24-30
• /
• 2003

This paper presents the characteristics of lifted height and flame length from non-premixed jet flames in highly preheated air to investigate the detail combustion mechanism in the gas turbine or HCCI engine, etc. Special attention was paid to the effect of preheated air temperature, oxygen concentration and fuel injection flow rate on flame length and lifted hight. By using highly preheated air, stable flames were formed even in low oxygen concentration condition. The lifted height increased with decreasing preheated air temperature, where the flame length showed opposed phenomena. The flamelet model, which is thought to have very thin flamelet, is difficult to applicable to the present flame conditions which is formed In low oxygen concentration in highly preheated air.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.29 no.1
• /
• pp.151-154
• /
• 2006

The high degree of viscosity and the non-Newtonian fluid dynamics characterizes the process inside a glass furnace. Because the temperature is fluctuating in very short time-intervals, it is hard to determine that the status of its fluctuation is stable or unstable. Usually Shewhart-chart is used to determine the control status. However because of the characteristics of the temperature fluctuations in the glass furnace it does not directly serve the purpose here. Therefore we suggest using ARIMA to diagnose control status and confirm that the method using ARIMA can be a better tool than Shewhart-chart.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.2-3
• /
• 2001

Characteristics of two-dimensional slab photonic crystal lasers will be summarized. Room temperature c.w operation is demonstrated at 1.6 $\mu\textrm{m}$ by using InGaAsP slab-waveguide triangular photonic crystal on top of wet-oxidized aluminum oxide. Recently, 2-D PBG structures have attracted a great deal of attention due to their simplicity in fabrication and theoretical study as compared to the three-dimensional counterparts [1]. Air-guided 2-D slab PBG lasers were reported by Caltech group (2). However, this air-slab structure is mechanically fragile and thermally unforgiving. Therefore, a new structure that can remove this thermal limitation is dearly sought after for 2-D PBG laser to have practical meaning. In this talk, we report room-temperature continuous operation of 2-D photonic bandgap lasers that are thermally and mechanically stable.(omitted)

• Transactions of Materials Processing
• /
• v.9 no.2
• /
• pp.186-192
• /
• 2000

Some deep drawing characteristics to the elevated temperatures were investigated for the SCPI steel sheets by using the Cr-coated die. For this investigations, six steps of temperature ranges, from room temperature to 25$0^{\circ}C$, and six kinds of drawing ratio, from 2.4 to 2.9 were adopted. As a result, the limiting drawing ratio, maximum drawing force, and the maximum drawing depth were sensitively affected by the elevated temperatures, and the more stable thickness strain distribution was observed to the elevated temperatures. Some experimental results were compared with analytical results using the DYNA-3D code.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1406-1411
• /
• 2004

A series of experiments was conducted to examine characteristics of a grooved flat-strip heat pipe having multiple heat sources. The inner grooves of the heat pipe have the aspect ratio of 1 to $2.5(0.42{\times}1.05$ mm) whose pitch was 0.6 mm. Four block heaters ($10{\times}20$ mm) were placed in the evaporator section at intervals of 20 mm and six different heating modes were tested. The maximum surface heat flux of 80 $W/cm^2$ was achieved while the operating temperature was kept below $100^{\circ}C$, In the nearest heating mode (from the condenser location), the heat pipe exhibited more stable temperature distribution than the far heating mode where the heaters is located furthest from the condenser.

• Journal of Life Science
• /
• v.10 no.2
• /
• pp.182-187
• /
• 2000

The optimized RAPD-PCR conditions, which can be utilized as a basic information for the analysis of the genetic characteristics were investigated with four onion varieties, named Changryungdaego, Yeoeuijuhwang, Yakwangju, and Dabonghwang using Operon primers, OPR01 (TGCGGGTCCT) and OPZ20 (ACTTTGGCGG). We tested several concentrations of DNA, primer, and MgCl2, annealing temperature, number of PCR cycle, and presence/absence of pre-heating time at the begining of PCR reation in the 25${mu}ell$ volume. The best RAPD profiles were obtained using 50ng of DNA, 5mM of primer, 1.5mM of MgCl2, 45$^{\circ}C$ of annealing temperature and an absence of pre-heating time. An establishment of the stable and reproducible RAPD-PCR conditions are expected to be useful for the subsequent RAPD-related investigation, such as genetic characterization of the onion strains, re-establishment of phylogenetic relationships and development of new varieties.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.52 no.5
• /
• pp.226-226
• /
• 2003

When an excessive voltage is applied to the discharge gap in ozone generator, the discharge room temperature becomes higher. As is well own, the efficiency of the ozone generation is deteriorated by the excessively hot temperature because of the decomposition reaction. In this paper, the simple small capacity ozone generating controller has been introduced, which provides effective and stable silent discharge characteristics over wide range input power. The proposed power controller has two important advantages, which imply that the production rate of ozone can be controlled linearly according to the delivered power and the surplus energy is recovered to the source. The experimental results are given to verify the performance of the pre proposed controller.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.5
• /
• pp.226-230
• /
• 2003

When an excessive voltage is applied to the discharge gap in ozone generator, the discharge room temperature becomes higher. As is well own, the efficiency of the ozone generation is deteriorated by the excessively hot temperature because of the decomposition reaction. In this paper, the simple small capacity ozone generating controller has been introduced, which provides effective and stable silent discharge characteristics over wide range input power. The proposed power controller has two important advantages, which imply that the production rate of ozone can be controlled linearly according to the delivered power and the surplus energy is recovered to the source. The experimental results are given to verify the performance of the pre proposed controller.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.561-564
• /
• 1987

The deposition and reflow properties or BPSG film deposited by APCVD was characterized by variation of each process parameter. As deposition temperature is increased higher, deposition rate is decreased. Maximum deposition rate of BPSG film is obtained in higher 02/Hyride ratio than CVD Oxide or PSG. BPSG film shows stable dielectric properties and we obtained good planarization effect at lower reflow temperature in case of BPSG film than PSG film.