• International Journal of Korean Welding Society
• /
• 제2권1호
• /
• pp.1-10
• /
• 2002

The thermal contact conductance at different temperatures and with different electrode forces and zinc coating morphology was measured by monitoring the infrared emissions from the one dimensionally simulated contact heat transfer experiments. The contact heat transfer coefficients were presented as a function of the harmonic mean temperature of the two contacting surfaces. Using these contact heat transfer coefficients and experimentally measured temperature profiles, the electrical contact resistivities both for the faying interface and electrode-workpiece interface were deduced from the numerical analyses of the one dimension simulation welding. It was found that the average value of the contact heat transfer coefficients for the material with zinc coating (coating weight from 0 g/$mm^2$to 100 g/$mm^2$) ranges from 0.05 W/$mm^2$$^{\circ}C$ to 2.0 W/$mm^2$$^{\circ}C$ in the temperature range above 5$0^{\circ}C$ harmonic mean temperature of the two contacting surfaces. The electrical contact resistivity deduced from the one dimension simulation welding and numerical analyses showed that the ratio of electrical contact resistivity at the laying interface to the electrical contact resistivity at the electrode interface is smaller than one far both bare steel and zinc coated steel.

• 대한기계학회논문집
• /
• 제12권1호
• /
• pp.137-151
• /
• 1988

본 논문에서는 아래 평판은 높은 온도 $T_{h}$로 유지되고, 위의 평판은 낮은 온도 $T_{i}$로 유지되어 있을 때 온도차에 의하여 발생하는 난류 열대류 문제를 난류모델 방정식을 사용하여 수치적으로 해석하고자 한다.다.다.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1138-1149
• /
• 1988

본 연구에서는 논란의 여지가 많은 문제점을 구간별 특성 척도 분석으로 보다 명확히 하고, 매질이 물과 공기인 경우 실험을 통하여 난류 열대류 구조를 분석하여 척도분석 및 Kraichnan등의 분석을 통해 확인된 바 있는 지수법칙층의 존재를 확인하 고자 한다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.629-634
• /
• 2011

초고속 비행체에 적용 가능한 소모성 터빈엔진 개발을 위한 사전연구를 수행하였다. 엔진 요구도 및 설계점 결정을 위한 가상 운용임무형상을 선정하고, 유사급 엔진과 참고문헌 등을 통해 확보된 데이터를 활용하여 설계점 해석을 수행하였는데, 해면고도, 마하수 1.2 조건에서 터빈입구온도 3,600R에 대한 설계점 계산결과, 비추력 2599.4 ft/s, 비연료소모율 1.483 lb/($lb^*h$)이 예측되었다. 설계점 계산결과를 기준으로 두 가지 임무형상에 대한 엔진 성능해석결과, 엔진 최대 순추력을 결정하는 설계변수는 천음속 및 낮은 초음속영역에서는 터빈입구온도, 높은 초음속 영역에서는 압축기 출구온도임을 확인하였다. 이밖에도 단순, 저가, 경량의 엔진형상으로 축류형 다단압축기와 직류형 연소기, 1단 축류터빈, 고정 수축팽창 노즐이 적용된 단순터보제트엔진을 제시하였다.

• Ocean and Polar Research
• /
• 제27권1호
• /
• pp.87-95
• /
• 2005

The vertical profiles of radiative flux and heating rate at King Sejong Station in West Antarctica were calculated with radiative transfe model by Chou and Suarez (1999) and Chou et al (2001). To run this model, the profiles of temperature, mixing ratios of water vapor and ozone at King Sejng Station were derived from ECMWF Reanalysis data. The surface temperature and albedo were also derived from NCEP/NCAR Reanalysis and CERES data. The radiative flux strongly depends on the cloud optical path length that was calculated using the measured W-h data and model by Chou and Lee(1996). Durins the period of $2000{\sim}2001$ (12 and 18 UTC), the correlation coefficient between calculated and measured downward solar fluxes at surface was 0.90 and the coefficient for downward longwave flux was 0.61. The calculated net heating rates of surface layer decreased during the same period, the trend of which was in accordance with the decrease of measured temperature.

• 대한기계학회논문집B
• /
• 제20권10호
• /
• pp.3371-3380
• /
• 1996

각종 노(furnace)를 포함하여 보일러, 가스터빈, 우주선 추진기구, 원자로 및 연료전지 등 고온이 열전달 문제를 다루는데 있어서 복사 열전달 연구는 매우 중요하다. 이러한 복사열전달에 대한 연구동향은 최근 복사 물성치(특히 가스에서의)를 예측하기 위한 이론 모델의 개발 및 측정분야와 복사전달 방정식의 해를 비교적 간단하게 구하기 위한 근사해법에 대한 연구로 크게 대별되고 있다. 이러한 두가지 연구방햐은 완전히 분리, 독립되어 있는 것은 아니며 서로 많은 연관성을 가지고 있다. 특히, 비회체가스(nongray gas)의 복사 성질에 대한 모델링은 근사 해법의 계산결과에 큰 영향을 미치게 되므로 가스의 복사 성질의 예측은 매우 중요한 연구 과제가 된고 있다. a Low resolution spectral modeling of water vapor is carried out by applying the weighted-sum-of-gray-gases model (WSGGM) to a narrow band. For a given narrow band, focus is placed on proper modeling of gray gas absorption coefficients vs. temeprature relation used for any solution methods for the Radiative Transfer Equation(RTE). Comparison between the modeled emissivity and the "true" emissivity obtained from a high temperatue statistical narrow band parameters is made ofr the total spectrum as well as for a few typical narrow bands. Application of the model to nonuniform gas layers is also made. Low resolution spectral intensities at the boundary are obtained for uniform, parabolic and boundary layer type temeprature profiles using the obtained for uniform, parabolic and boundary layer type temperature profiles using the obtained WSGGM's with 9 gray gases. The results are compared with the narrow band spectral intensities as obtained by a narrow band model-based code with the Curtis-Godson approximation. Good agreement is found between them. Local heat source strength and total wall heat flux are also compared for the cases of Kim et al, which again gives promising agreement.

• Fibers and Polymers
• /
• 제7권4호
• /
• pp.432-435
• /
• 2006

High Modulus and high tenacity polypropylene fibers have been prepared by drawing on a gradient heater. Results show that fiber properties are significantly affected by temperature profiles of final stage drawing on a gradient heater. The gradient drawn filaments showed superior mechanical properties when compared to filaments drawn over a constant temperature heater. Fibers with initial modulus of 16.4 GPa and tenacity of 670 MPa have been manufactured in the process. The nature of the gradient drawing had a significant effect on end properties. The superior mechanical properties are attributed to the high crystal perfection and crystallinity and low void fractions obtained at high draw ratios when drawn over a gradient heater.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.21-24
• /
• 2014

In the entrained-flow coal gasifier, coal ash turns into a molten slag most of which deposits onto the wall to form liquid and solid layers. Critical viscosity refers to the viscosity at the interface of the two layers. The slag layers play an important role in protecting the wall from physical/chemical attack from the hot syngas and in continuously discharging the ash to the slag tap at the bottom of the gasifier. For coal with high ash melting point and slag viscosity, CaO-based flux is added to coal to lower the viscosity. This study evaulates the effect of critical viscosity temperature and ash/flux ratio on the slag behavior using numerical modelling in a commercial gasifier. The changes in the slag layer thickness, heat transfer rate, surface temperature and velocity profiles were analyzed to understand the underlying mechanism of slag flow and heat transfer.

• Journal of Mechanical Science and Technology
• /
• 제15권5호
• /
• pp.656-664
• /
• 2001

A theoretical analysis is performed to describe the qualitative behavior of transient buoyant flows in a vertical channel. Consideration is given to the case of a fluid with a pre-existing stratification. The fluid motion is generated by giving impulsive anti-symmetric step-changes in temperature at the vertical left ad right sidewalls. The qualitative character of the flow is shown to be classified in the Rayleigh number (Ra)-Prandtl number ($sigma$) diagram. The transitory approach to the steady state can be monotonic or oscillatory, depending on ($sigma$-1)$^2$$pi$$^4$ 4$sigma$$R_a$. The prominent characteristics of time-dependent flow are discussed for large $R_a$. The profiles of temperature and velocity in the transient phase are depicted, which disclose distinctive time scales of motion. The transient process is shown to be sensitive to the Prandtl number. The detailed evolutions of flow and temperature fields are illustrated for large $R_a$.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.190-193
• /
• 2008

The heat transfer characteristics of molten salt storage system for the solar thermal power generation were investigated. Temperature profiles and the heat transfer coefficients during the storage and discharge stage were obtained with the steam as the heat transfer fluid. Two kinds of inorganic salt were employed as the storage materials and coil type of heat exchanger were installed in both tanks to provide the heat transfer surfaces during the storage and discharge stage. The effects of steam flow rates, flow direction of steam in the storage tank and the initial temperature of storage and discharge tank on the heat transfer were tested.