• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 대한약리학회지
• /
• 제16권2호
• /
• pp.55-70
• /
• 1980

The pharmacological and microbiological studies of Cefoperazone (T-1551, Toyama Chemical Co., Japan) were conducted in vitro and in vivo. The studies included stability and physicochemical characteristics, antimicrobial activity, animal and human pharmacokinetics, animal pharmacodynamics and safety evaluation of Cefoperazone sodium for injection. 1) Stability and physicochemical characteristics. Sodium salt of cefoperazone for injection had a general appearance of white crystalline powder which contained 0.5% water, and of which melting point was $187.2^{\circ}C$. The pH's of 10% and 25% aqueous solutions were 5.03 ana 5.16 at $25^{\circ}C$. The preparations of cefoperazone did not contain any pyrogenic substances and did not liberate histamine in cats. The drug was highly compatible with common infusion solutions including 5% Dextrose solution and no significant potency decrease was observed in 5 hours after mixing. Powdered cefoperazone sodium contained in hermetically sealed and ligt-shielded container was highly stable at $4^circ}C{\sim}37^{\circ}C$ for 12 weeks. When stored at $4^{\circ}C$ the potency was retained almost completely for up to one year. 2) Antimicrobial activity against clinical isolates. Among the 230 clinical isolates included, Salmonella typhi was the most susceptible to cefoperazone, with 100% inhibition at MIC of ${\leq}0.5{\mu}g/ml$. Cefoperazone was also highly active against Streptococcus pyogenes(group A), Kletsiella pneumoniae, Staphylococcus aureus and Shigella flexneri, with 100% inhibition at $16{\mu}g/ml$ or less. More than 80% of Escherichia coli, Enterobacter aerogenes and Salmonella paratyphi was inhibited at ${\leq}16{\mu}/ml$, while Enterobacter cloaceae, Serratia marcescens and Pseudomonas aerogenosa were somewhat less sensitive to cefoperagone, with inhibitions of 60%, 55% and 35% respectively at the same MIC. 3) Animal pharmacokinetics Serum concentration, organ distritution and excretion of cefoperazone in rats were observed after single intramuscular injections at doses of 20 mg/kg and 50 mg/kg. The extent of protein binding to human plasma protein was also measured in vitro br equilibrium dialysis method. The mean Peak serum concentrations of $7.4{\mu}g/ml$ and $16.4{\mu}/ml$ were obtained at 30 min. after administration of cefoperazone at doses of 20 mg/kg and 50 mg/kg respectively. The tissue concentrations of cefoperazone measured at 30 and 60 min. were highest in kidney. And the concentrations of the drug in kidney, liver and small intestine were much higher than in blood. Urinary and fecal excretion over 24 hours after injetcion ranged form 12.5% to 15.0% in urine and from 19.6% to 25.0% in feces, indicating that the gastrointestinal system is more important than renal system for the excretion of cefoperazone. The extent of binding to human plasma protein measured by equilibrium dialysis was $76.3%{\sim}76.9%$, which was somewhat lower than the others utilizing centrifugal ultrafiltration method. 4) Animal pharmacodynamics Central nervous system : Effects of cefoperazone on the spontaneous movement and general behavioral patterns of rats, the pentobarbital sleeping time in mice and the body temperature in rabbits were observed. Single intraperitoneal injections at doses of $500{\sim}2,000mg/kg$ in rats did not affect the spontaneous movement ana the general behavioral patterns of the animal. Doses of $125{\sim}500mg/kg$ of cefoperazone injected intraperitonealy in mice neither increased nor decreased the pentobarbital-induced sleeping time. In rabbits the normal body temperature was maintained following the single intravenous injections of $125{\sim}2,000mg/kg$ dose. Respiratory and circulatory system: Respiration rate, blood pressure, heart rate and ECG of anesthetized rabbits were monitored for 3 hours following single intravenous injections of cefoperazone at doses of $125{\sim}2,000mg/kg$. The respiration rate decreased by $3{\sim}l7%$ at all the doses of cefoperazone administered. Blood pressure did not show any changes but slight decrease from 130/113 to 125/107 by the highest dose(2,000 mg/kg) injected in this experiment. The dosages of 1,000 and 2,000 mg/kg seemed to slightly decrease the heart rate, but it was not significantly different from the normal control. All the doses of cefoperazone injected were not associated with any abnormal changes in ECG findings throughout the monitering period. Autonomic nervous system and smooth muscle: Effects of cefoperazone on the automatic movement of rabbit isolated small intestine, large intestine, stomach and uterus were observed in vitro. The autonomic movement and tonus of intestinal smooth muscle increased at dose of $40{\mu}g/ml$ in small intestine and at 0.4 mg/ml in large intestine. However, in stomach and uterine smooth muscle the autonomic movement was slightly increased by the much higher doses of 5-10 mg/ml. Blood: In vitro osmotic fragility of rabbit RBC suspension was not affected by cefoperazone of $1{\sim}10mg/ml$. Doses of 7.5 and 10 mg/ml were associated with 11.8% and 15.3% prolongation of whole blood coagulation time. Liver and kidney function: When measured at 3 hours after single intravenous injections of cefoperaonze in rabbits, the values of serum GOT, GPT, Bilirubin, TTT, BUN and creatine were not significantly different from the normal control. 5) Safety evaluation Acute toxicity: The acute toxicity of cefoperazone was studied following intraperitoneal and intravenous injections to mice(A strain, 4 week old) and rats(Sprague-Dawler, 6 week old). The LD_(50)'s of intraperitonealy injected cefoperazone were 9.7g/kg in male mice, 9.6g/kg in female mice and over 15g/kg in both male and female rats. And when administered intravenously in rats, LD_(50)'s were 5.1g/kg in male and 5.0g/kg in female. Administrations of the high doses of the drug were associated with slight inhibition of spontaneous movement and convulsion. Atdominal transudate and intestinal hyperemia were observed in animals administered intraperitonealy. In rats receiving high doses of the drug intravenously rhinorrhea and pulmonary congestion and edema were also observed. Renal proximal tubular epithelial degeneration was found in animals dosing in high concentrations of cefoperazone. Subacute toxicity: Rats(Sprague-Dawley, 6 week old) dosing 0.5, 1.0 and 2.0 g/kg/day of cefoperazone intraperitonealy were observed for one month and sacrificed at 24 hours after the last dose. In animals with a high dose, slight inhibition of spontaneous movement was observed during the experimental period. Soft stool or diarrhea appeared at first or second week of the administration in rats receiving 2.0g/kg. Daily food consumption and weekly weight gain were similar to control during the administration. Urinalysis, blood chemistry and hematology after one month administration were not different from control either. Cecal enlargement, which is an expected effect of broad spectrum antibiotic altering the normal intestinal microbial flora, was observed. Intestinal or peritoneal congestion and peritonitis were found. These findings seemed to be attributed to the local irritation following prolonged intraperitoneal injections of hypertonic and acidic cefoperazone solution. Among the histopathologic findings renal proximal tubular epithelial degeneration was characteristic in rats receiving 1 and 2g/kg/day, which were 10 and 20 times higher than the maximal clinical dose (100 mg/kg) of the drug. 6) Human pharmacokinetics Serum concentrations and urinary excretion were determined following a single intravenous injection of 1g cefoperazone in eight healthy, male volunteers. Mean serum concentrations of 89.3, 61.3, 26.6, 12.3, 2.3, and $1.8{\mu}g/ml$ occured at 1,2,4,6,8 and 12 hours after injection respectively, and the biological half-life was 108 minutes. Urinary excretion over 24 hours after injection was up to 43.5% of administered dose.

• Journal of Chest Surgery
• /
• 제35권10호
• /
• pp.712-723
• /
• 2002

체외순환은 뇌 혈류의 변화를 유도하며 이러한 변화가 수술 후 직 간접적인 뇌 손상의 원인이 될 수도 있다. 최근 체외순환 중 뇌 혈류 변화는 동맥혈액의 이산화탄소 분압과 밀접한 관련이 있는 것으로 보고되고 있다. 본 연구는 체외순환을 이용한 심장수술시 뇌 대사에 대한 정상 탄산분압과 고 탄산분압의 임상적 영향을 비교 조사하기 위해 전향적으로 계획되었다. 대상 및 방법: 심장수술이 계획된 36명의 성인 환자들을 연구목적에 따라 무작위적으로 정상탄산분압군(Pa$CO_2$35~40 mmHg, n＝18) 혹은 고탄산분압군(Pa$CO_2$45~55 mmHg, n＝18)으로 나눈 뒤 중등도 저체온(비인두 온도 29~3$0^{\circ}C$)의 비박동성 체외순환을 실시하였다. 수술 중, 각 환자들의 중대뇌동맥 혈류속도(뇌혈류 속도), 뇌동정맥 산소함량 차, 뇌산소 추출률, 뇌산소 대사율, 뇌산소 운반율, 뇌산소운반/뇌산소대사 비율, 뇌정맥 산소 불포화도(내경 정맥구 혈액 산소 포화도$\leq$50%), 동맥혈액 및 내경정맥 혈액 가스분석 등을 평가하였고, 수술 후 신경학적 합병증(섬망증세) 발생 정도 역시 관찰하여 양 그룹간에 비교하였다. 결과 : 체외순환 동안 고탄산분압군이 정상탄산분압군에 비해 뇌혈류 속도(169.13 $\pm$ 8.32 vs 153.11 $\pm$8.98%), 뇌산소 운반율(1,911.17$\pm$250.14 vs 1,757.40$\pm$249.56), 뇌산소운반/뇌산소대사 비율(287.38$\pm$28.051 vs 246.77$\pm$25.84), 내경 정맥구 산소분압(41.66$\pm$9.19 vs 31.50$\pm$6.09 mmHg), 그리고 내경 정맥구 산소포화도(68.97$\pm$10.96 vs 58.12$\pm$12.11%) 등이 유의하게 더 높았으나 (p＝0.03), 뇌동정맥 산소함량차(3.9$\pm$0.3 vs 4.9$\pm$0.3 mL/dL), 뇌산소 추출률(0.3$\pm$0.03 vs 0.4$\pm$0.03), 뇌산소 대사율(5.8 $\pm$0.5 vs 6.8$\pm$0.6), 동맥혈 pH는 고탄산분압군이 더 낮았다(7.36$\pm$0.09 vs 7.46$\pm$0.07, p＝0.04). 체외순환 동안 뇌정맥혈 불포화를 보인 환자 수는 고탄산분압군이 정상탄산분압군 보다 유의하게 더 적었다(3명 vs 9명, p＝0.03). 수술 후 신경학적 합병증(섬망)의 지속시간 역시 고탄산분압군이 정상탄산분압군 보다 더팔았다(36시간 vs 60시간, p=0.009). 결론: 이상의 연구결과들은 심장수술 동안 고탄산분압 체외순환이 뇌대사 및 수술 후 신경학적 결과에 보다 유익한 효과를 제공해 줄 수 있음을 시사하고 있다.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• 한국토양비료학회지
• /
• 제9권1호
• /
• pp.17-23
• /
• 1976

답토양(畓土壤)의 질소(室素)의 동태(動態)를 파악(把握)하기 위하여 성질(性質)이 다른 3개지역(個地域)의 토양(土壤)을 공시(供試)하여 지력질소(地力窒素)의 발현양식(發現樣式)과 토양(土壤)의 종류(種類), 온도(溫度), 토양(土壤)의 길이, 질소비료(窒素肥料)의 종류(種類), 담수일수(湛水日數)에 따른 $NH_4-N$, $NO_3-N$, 2가철(價鐵) pH의 변화(變化)와 이들 상호관계(相互關係)를 검토(檢討)하여 탈질량(脫窒量)을 추정(推定)하고 지역(地域)에 알맞는 질소시비법(窒素施肥法)을 확립(確立)하기 위한 기초적(基礎的) 지견(知見)을 얻을 목적(目的)으로 실험(實驗)하여 얻어진 결과(結果)를 요약(要約)하면 다음과 같다. 1. 온도상승효과는 화순(和順), 서창(西倉), 서산토양(瑞山土壤)의 순(順)이었으나 건토효과는 서산(瑞山), 화순(和順), 서창(西倉)의 순(順)이였고 $NH_4-N$의 생성율(生成率)은 서산(瑞山), 서창(西倉), 화순(和順)의 순(順)으로 토양(土壤)의 성질(性質)에 따라 상이(相異)했다. 2. 표면수중(表面水中) $NH_4-N$의 변화(變化)는 일반적(一般的)으로 토양중(土壤中)의 함량(含量)에 좌우(左右)되며 염안(鹽安), 유안구(硫安區)가 많고 담수(湛水) 3일(日)에 감소(減少)했다가 40일(日)에 다시 증가(增加)된 후(後) 50일(日)에 감소(減少)하였고 요소구(尿素區), SCU는 함량(含量)이 적었으며 담수기간(湛水期間) 비교적(比較的) 일정(一定)했다. 3. 토양중(土壤中) $NH_4-N$의 변화(變化)는 1층(層)은 염안(鹽安), 유안구(硫安區)가 집적(集積)이 많으며 SCU, 요소구(尿素區)는 적었다. 토양(土壤)의 종류(種類)에 따라서도 비교적(比較的) 같은 경향(傾向)을 나타냈으며 경시적(經時的)으로 함량(含量)은 감소(減少)했다. 2층(層)도 산화층(酸化層)과 같은 경향(傾向)을 나타냈다. 4. 표면수중(表面水中) $NO_3-N$의 변화(變化)는 토양(土壤)과 비료(肥料)의 종류(種類)에 따라 다르나 일반적(一般的)으로 요소(尿素), SCU구(區)가 함량(含量)이 많고 염안(鹽安), 유안구(硫安區)가 적었으며 담수(湛水) 30~40일(日)에 소실(消失)되었다. 5. 토양중(土壤中) $NO_3-N$의 변화(變化)는 1층(層)은 2층(層)에 비(比)하여 $NO_3-N$의 함량(含量)이 많고 토양(土壤)과 비료(肥料)에 따라 변화(變化)되는 양상(樣相)이 다르며 일반적(一般的)으로 담수(湛水) 30일(日)에 소실(消失)되었다가 그 후(後) 증가(增加)되었으며 요소(尿素), SCU구(區)가 질화(窒化)가 잘되는 편이며 2층(層)은 담수(湛水) 30일(日)까지는 함량(含量)이 적거나 거의 소실(消失)되었다가 40일(日) 이후(以後)는 야간증가(若干增加)했다. 6. 표면수(表面水)와 토양중(土壤中) $NH_4-N$, $NO_3-N$의 함량(含量)으로 보아 담수(湛水) 기간중(期間中) 시용(施用)한 질소(窒素)의 반량이상(半量以上)이 탈질(脫窒)되는 것으로 추정(推定)되며 요소(尿素) SCU 구(區)는 염안(鹽安) 유안구(硫安區)에 비(比)하여 탈질량(脫窒量)이 많으리라 추정(推定)되였다.

• 한국산림과학회지
• /
• 제82권2호
• /
• pp.152-165
• /
• 1993

본(本) 연구(硏究)는 heat pulse법(法)을 이용하여 낙엽송 임분(林分)의 증산량(蒸散量)을 알기 위한 기초 연구로써, 일사량(日射量), 온도(溫度), 습도(濕度) 등의 변화에 따른 heat pulse 속도(速度)의 일변화와 계절변화, 방위별 heat pulse 속도(速度)의 차이, 변재부(邊材部)에 있어서 깊이별 heat pulse 속도(速度)의 차이, 우세목(優勢木), 준우세목(準優勢木), 열세목(劣勢木)의 heat pulse 속도(速度)의 차이, 엽(葉)의 수분(水分)포텐셜과 heat pulse 속도(速度)와의 관계, 줄기에 있어 수분상승의 방향, heat pulse법(法)으로 추산한 임분(林分)의 증산량(蒸散量)등에 대하여 측정 고찰하였다. 얻어진 결과를 요약하연 다음과 같다. 1 낙엽송의 heat pulse 속도(速度)(V)와 수액유속(樹液流速)(SFR)과의 관계는 SFR=1.37V($r=0.96^{**}$)의 식으로 나타냈다. 2. 우세목(優勢木), 준우세목(準優勢木), 열세목(劣勢木)의 heat pulse 속도(速度)를 비교하면, 수액유속(樹液流速)은 우세목(優勢木)이 가장 높고, 준우세목(準優勢木), 열세목(劣勢木) 순위였다. Heat pulse 속도(速度)는 일사량(日射量), 온도(溫度), 대기포차(大氣飽差) 등의 크기에 따라 심한 변화(變化)를 나타냈다. 3. 입목(立木) 개체간(個體間)의 heat pulse 속도(速度)의 차이는 이른 아침과 밤에는 거의 없으나, 일사량(日射量)이 높은 12시부터 16시 사이에는 약간의 차이를 나타냈다. 4. Heat pulse 속도(速度)와 수분(水分)포텐셜은 거의 비슷한 일변화 경향을 나타냈다. 5. Heat pulse 속도(速度)의 계절변화는 8월에 가장 높았고, 10월이 가장 낮았다. 그리고 6, 7, 9월의 heat pulse 속도(速度)는 거의 비슷한 값을 나타냈다. 6. 줄기에 있어 방위별 heat pulse 속도(速度)는 동측이 가장 높았고, 서측과 북측은 비슷한 속도를 나타냈으며, 남측의 속도가 가장 낮았다. 7. 변재부(邊材部)에 있어서 깊이별 heat pulse 속도(速度)의 차이는 수피(樹皮)로부터 2cm 깊이에서 가장 높고, 다음이 1cm 깊이, 그리고 3cm 깊이에서 가장 낮았다. 8. 줄기에 있어 수분이동방향(水分移動方向)은 5본 모두 오른쪽 나선상승(螺旋上昇)(spiral ascent turning right)을 나타내고 있었다. 특히 지상의 3m까지는 매우 느린 회선(回旋)을 나타내다가 그 이상의 수고(樹高)에서는 매우 빠른 회선(回旋)으로 상승됨을 알 수 있었다. 9. 수액유량(樹液流量)(SF)은 SF=1.37AV 식(式)으로 나타났고, 이 식으로 구한 수액유량(樹液流量)은 우세목(優勢木)이 준우세목(準優勢木)과 열세목(劣勢木)보다 현저히 높았다. 10. 1ha의 임분(林分)에 대한 1일의 증산량(蒸散量)의 구성비율(構成比率)은 낮이 83%, 밤이 17%였고, 증산량(蒸散量)은 약 30.8ton/ha/day이었다. 11. 1ha의 월별(月別) 증산량(蒸散量)은 8월이 1,194ton/ha/month로 가장 많았고, 5월이 386ton/ha/month로 가장 낮았다. 또 1ha의 연간(年間) 증산량(蒸散量)은 3,983ton/ha/yr이었다.

• Tuberculosis and Respiratory Diseases
• /
• 제42권6호
• /
• pp.871-877
• /
• 1995

연구배경: 중환자의 예후를 정량화하는 체점체계 중 APACHE III system은 중환자실 제 1병일 점수는 물론 일갱신 점수도 환자의 위험도를 갱신하는 것이 알려진 바 있어 패혈증 환자들에서 APACHE III score의 예후 지표로서의 가치를 알아 보고자 하였다. 방법: 48명의 패혈증 환자들에서 후향적으로 중환자실 제 1병일, 2병일 및 3병일의 APACHE III score를 조사하여 패혈증 생존자와 비생존자 간의 차이를 분석하였다. 결과: 패혈증 생존자는 비생존자에 비해 APACHE III system에 따른 중환자실 제 1병일 정수가 유의하게 낮았으며, 제 2일 및 제 3일의 점수도 각각의 전날 점수에 비해 유의하게 감소하였다. 폐혈증 비생존자의 경우 제 1병일 점수가 생존자에 비해 높았고, 제 2병일 및 제 3병일 점수 역시 각각의 전날 점수에 비해 증가하는 경향을 보였다. 결론: APACHE III system에 따른 제 1병일 점수 및 제 3병일까지의 점수의 일변동은 패혈증 환자의 예후를 반영하는 것으로 사려된다.

• 한국농림기상학회지
• /
• 제23권4호
• /
• pp.329-339
• /
• 2021

콩은 논 대표적인 밭작물로써 온도, 수분, 토양과 같은 환경 조건에 민감하기 때문에 재배 시 포장 관리가 매우 중요하다. 작물 상태를 비파괴적, 비접촉적 방법으로 측정할 수 있는 분광 기술을 활용한다면 작황 예측, 작물 스트레스 및 병충해 판별 등 생육 진단 및 처방을 통해 품질과 수확량을 높일 수 있다. 본 연구에서는 회전익 무인기에 탑재된 다중분광 센서를 이용하여 시험 포장에서 콩 생육 추정 모델 개발하고 재현성을 확인하기 위해 농가 포장에 검증을 수행하였다. 분광 데이터로 산출된 정규화 식생지수(NDVI, GNDVI), 단순비 식생지수(RRVI, GRVI)와 콩 생육 데이터(생체중, LAI)를 선형회귀분석을 실시하여 모델을 개발하였으며 괴산에 위치한 농가포장에서 검증을 실시하였다. 그 결과 생체중의 경우 정규화 식생지수를 이용 시 포화되기 때문에 단순비 식생지수 GRVI를 이용한 모델의 성능이 가장 높았다(R²=0.74, RMSE=246 g/m², RE=34.2%). 괴산 농가 포장에 생체중 모델 검증 결과 RMSE=392 g/m², RE=32%로 나타났으며 작부 체계별 나누어 검증 결과 단작 포장과 이모작 포장 생체중 모델은 RMSE=315 g/m², RE=26% 및 RMSE=381 g/m², RE=31%로 나타났다. 작부 체계별 포장과 적산온도가 유사한 연도별 시험 포장(2018+2020년, 2019년)을 나누어 생체중 모델 개발한 결과 단년도(2019년)의 성능이 높게 나타났다. 작부 체계별 적산온도가 유사한 검증과 기존 검증 간 비교 결과 단작 포장은 RMSE 및 RE를 기준으로 각각 29.1%와 34.3%로 개선되었으나 이모작 포장은 -19.6%, -31.3%로 저하되었다. 적산온도 이외의 환경 요인, 분광 및 생육 데이터 추가 시 다양한 환경 조건에서 재배되는 콩 생육을 추정 가능할 것으로 판단된다.

• 한국양식학회지
• /
• 제21권4호
• /
• pp.309-316
• /
• 2008

사료내 다양한 사료 첨가제 공급에 따른 전복의 성장과 스트레스(공기중 노출, 급격한 온도 변화 및 급격한 염분 변화)에 대한 전복의 내성에 미치는 영향을 조사하였다. 21개의 직사각형 50 L 플라스틱 용기에 각각 70 마리의 치패(시작시 무게 4.2 g)를 수용하여 3개의 1.3톤 raceway에 분산 수용하였다. 다양한 원료의 사료첨가제를 이용하여 6종류의 실험사료 [대조구 (CON), 녹차부산물 첨가(BPC), 무화과엑기스 첨가(EF), 녹차엑기스 첨가(EG), 시판용 해록상품 첨가(PH) 및 Haematococcus 첨가(HC)]를 제조하였으며, 이들 실험사료의 유용성을 평가하기 위하여 건조 다시마(ST)를 공급하는 실험구와 비교하였다. 실험사료는 어분, 대두박 및 새우머리분을 주요 단백질원으로 공급하였으며, 덱스트린, 다시마분말 및 소맥분을 주요 탄수화물원으로 공급하였으며, 대두유와 어유를 주요 지질원으로 공급하여 주었다. 전복은 1일 1회 사료가 조금씩 남아서 만복시까지 먹게끔 충분한 양의 사료를 공급하여 주었다. 각 실험구는 3반복구를 두었으며, 총 사육기간은 16주간이었다. 16주간의 사육실험 종료후, 각 실험 구에서 생존한 전복은 10마리씩 무작위로 추출하여 공기노출, 급격한 온도 변화 및 급격한 염분변화의 스트레스를 주어서 이들의 누적폐사율을 조사하였다. 16주간의 사육실험 종료시 전복의 생존율은 다시마를 공급한 실험구에서 가장 높았다. 그러나 전복의 체중증가는 무화과엑기스, 녹차엑기스 및 해록상품을 첨가한 실험사료를 공급한 실험구에서 녹차부산물 첨가한 시험구 또는 다시마를 공급한 실험구에 비하여 유의적으로 높게 나타났다. 전복의 각장은 다시마를 공급한 실험구에 비하여 실험용 사료를 공급한 모든 실험구에서 유의적으로 높게 나타났다 다양한 형태의 스트레스에 노출시 전복의 누적폐사율은 다시마를 공급한 실험 구에서 낮게 나타났으며, Haematococcus 첨가구 및 무화과엑기스 첨가구에서도 비교적 낮은 전복의 폐사율을 보였다. 이상의 결과를 고려할 때, 본 실험에 이용된 다양한 사료첨가제는 전복의 성장을 개선시키는데 효과적이며, 특히 Haematococcus와 무화과엑기스는 다양한 형태의 스트레스의 내성을 개선시키는 사료 첨가제로서 이용 가능한 것으로 판단된다.