• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.115-127
• /
• 2019

The low-flow grouting injection technique, the target construction method for this study, is a method of pouring mortar into the ground by non-emission replacement principle, which can be expected to increase the density of the ground, and, in some cases, be used as a base file using the strength of the high injection solids, along with low noise, low pollution, and high durability. To verify that the dynamic characteristics of the ground are improved by the low-flow injection technique, the test work was conducted on the site and physical tests were performed, and the quality of the improvement formed in the ground was verified through the indoor test on the core and core recovery rate was analyzed. The density logs test layer calculated the volume density of the ground layer by using the Compton scattering of gamma-rays, and the sonic logs was tested on the ground around the drill hole using a detector consisting of sonar and receiver devices inside the drill hole. As a result of the measurement of the change in physical properties (density and sonic logs) before and after grouting, both properties were basically increased after infusion of grout agent. However, the variation in density increase was greater than the increase in speed after grouting, and the ground density measurement method was thought to be effective in measuring the fill effect of the filler. Strength and core recovery rates were measured from specimens taken after the age of 28 days, and the results of the test results of the diffusion and strength test of the improved products were verified to satisfy the design criteria, thereby satisfying the seismic performance reinforcement.

• Journal of the Korean GEO-environmental Society
• /
• v.4 no.3
• /
• pp.41-49
• /
• 2003

If MSW(Municipal Solid Waste) landfill is used as a foundation ground of construction site, the change of loading condition may cause a large amount of compression in MSW landfill. Therefore, the reinforcement for the loose compression nature of MSW landfill would be very important design factor to geotechnical engineers in considering the end-use of the landfill. In this study, a possible technique for stabilizing MSW landfill with use of codisposal of municipal solid waste and Fly Ash is discussed. In order to estimate the stabilization of compression characteristic of codisposed landfill, large compression test and lysimeter test were performed. According to the test results, as the proportion of Fly Ash increases, the compression might be reduced, but the permeability might be also reduced. Therefore, it is necessary to take into account the both characteristics changes in real application.

• Tunnel and Underground Space
• /
• v.17 no.5
• /
• pp.411-427
• /
• 2007

Reliability in tunnel analysis is necessary to accomplish technically sound design and economical construction. For this, a thorough understanding of the construction procedure including the ground-support interaction has to be obtained. This paper describes a proper modelling technique to simulate the behavior of the steel fiber reinforced shotcrete (SFRS) which maintain the supporting capability in post-failure regime. The additional supporting effect of the steel support was also verified by 3-D analyses and a new load distribution factor were proposed. The use of the plastic moment limit (PML) alone can eliminate the occurrence of the awkwardly high tensile stress in the shotcrete and can successfully model the post-peak ductile behavior of the SFRS. But with this method, moment is limited whenever the stress caused by moment reaches tensile strength of the shotcrete irrespective of the stress by axial force. Therefore, it was necessary to find a more comprehensive method which can reflect the influence of the moment and axial force. This can be accomplished by the proper use of "liner element" which is the built-in model in FLAC. In this model, the peak and residual strength as well as the uniaxial compressive strength of the SFRS can be specified. Analyses were conducted with these two models on the 2-lane road tunnels excavated in class IV and V rock mass and results were compared with the conventional elastic beam model. Results showed that both models can reflect the fracture toughness of the SFRS which could not be accomplished by the elastic beam model.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.2
• /
• pp.170-176
• /
• 2012

In the nuclear industry, wall thinning defect of straight pipe occur the enormous loss in life evaluation and safety evaluation. To use non-destructive technique, we measure deformation, vibration, defect evaluation. But, this techniques are a weak that is the measurement of the wide area is difficult and the time is caught long. In the secondary side of nuclear power plants mostly used steel pipe, artificiality wall thinning defect make in the side and different thickness make to the each other, wall thinning defect part of deformation measure by using shearography. In addition, optical measurement through deformation, vibration, defect evaluation evaluate pipe and thickness defects of pressure vessel is to evaluate quantitatively. By shearography interferometry to measure the pipe's internal wall thinning defect and the variation of pressure use the proposed technique, the quantitative defect is to evaluate the thickness of the surplus. The amount of deformation use thickness of surplus prediction of the actual thickness defect and approximately 7 percent error by ensure reliability. According to pressure the amount of deformation and the thickness of the surplus through DB construction, nuclear power plant pipe use wall thinning part soundness evaluation. In this study, pressure vessel of thickness defect measure proposed nuclear pipe of wall thinning defect prediction and integrity assessment technology development. As a basic research defected theory and experiment, pressure vessel of advanced stability and soundness and maintainability is expected to contribute foundation establishment.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.4D
• /
• pp.377-386
• /
• 2010

This study was conducted to find out the characteristics of the expanded road embankment constructed by the lightweight air-mixed soil (slurry density $10kN/m^3$) for a short-term without any ground improvement. Compression strength, capillary rise height of the lightweight air-mixed soil and settlement behavior of soft ground were studied. Compression strengths of the specimens sampled at the site after 1 and 5 months of construction were all satisfied the required strength 500 kPa. However, it was not convinced the homogeneity construction, because the values of strength were depending on the sampled location. Also, strength difference between laboratory and site specimens were found about 19%, and thus it should be considered for mixing design. Capillary rise reached about 20 cm for 70 hours because of a numerous tiny pores existed inside the lightweight air-mixed soil. Relationship between settlement and time of the soft ground placed underneath the expanded embankment was estimated by using the measured data and back analysis technique. The current average consolidation ratio and the final settlement after 120 months later were estimated about 32% and 4.5cm, respectively. This settlement is much less value than the allowable settlement 10cm for this structure.

• The Journal of Engineering Geology
• /
• v.27 no.2
• /
• pp.165-172
• /
• 2017

This research aims to define influence factors to perform an optimized section design and evaluate tunnel collapse risk during construction using Delphi technique. A total of five upper classification systems were constructed through literature review, pervious research analysis, and brainstorming of expert group for establishing influence factors. The $1^{st}$, $2^{nd}$, and $3^{rd}$ Delphi survey process was proceeded by panel group which is consisted 21 experts to prevent errors and bias in the expert judgement process. In Delphi $1^{st}$ survey, a total of 22 influence factors candidates were derived through open-ended questionnaire. In Delphi $2^{nd}$ survey, questionnaire was proceeded based on 7-point Likert scale method. In order to verify the validity, CVR (Content Validity Ration) analysis was performed to exclude inappropriate candidates. In the $3^{rd}$ survey, verification of influence factors was proceeded once more with the result of $2^{nd}$ survey, and lastly, a total of 14 influence factors was derived by CVR and COV (Content Validity Ration) analysis for response of experts.

• Journal of the Korea Concrete Institute
• /
• v.21 no.6
• /
• pp.681-688
• /
• 2009

The railroad bridges have been usually experienced by vibration and impact in service state. With this reason, it is important that the effective strengthening capacity should be considered to resist the kind of service loading. In this study, NSM strengthening technique is recommended for the concrete railroad bridge because of its better effective resistance for dynamic loading condition and strengthening cost than the conventional externally bonded strengthening using fiber sheet. However, to widely apply NSM method for the concrete railroad bridge, it needs that the strengthening ratio has to be reasonably evaluated with geometrical and material uncertainties, especially for the concrete bridge under long-term service state without the apparent design history and detail information such as concrete compressive strength, reinforcing ratio, railroad characteristics. The purpose of this study is to propose the critical strengthening ratio of CFRP plate for the targeted concrete railroad bridge with uncertainties of deterioration of the structures. To do this, Monte Carlo Simulation (MCS) for geometrical and material uncertainties have been applied so that this approach may bring the reasonable strengthening ratio of CFRP plate considering probabilistic uncertainties for the targeted concrete railroad bridge. Finally, the critical strengthening ratio of NSM strengthened by CFRP plate is calculated by using the limit state function based on the target reliability index of 3.5.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.3
• /
• pp.162-168
• /
• 2017

Shallow-water bathymetry survey has been conducted using high definition color images obtained at the altitude of 100 m above sea level using a drone. Shallow-water bathymetry data are one of the most important input data for the research of beach erosion problems. Especially, accurate bathymetry data within closure depth are critically important, because most of the interesting phenomena occur in the surf zone. However, it is extremely difficult to obtain accurate bathymetry data due to wave-induced currents and breaking waves in this region. Therefore, optical remote sensing technique using a small drone is considered to be attractive alternative. This paper presents the potential utilization of image processing algorithms using multi-variable linear regression applied to red, green, blue and grey band images for estimating shallow water depth using a drone with HD camera. Optical remote sensing analysis conducted at Wolpo beach showed promising results. Estimated water depths within 5 m showed correlation coefficient of 0.99 and maximum error of 0.2 m compared with water depth surveyed through manual as well as ship-board echo-sounder measurements.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.10
• /
• pp.69-77
• /
• 1998

This paper presents a new efficient and stable multilevel partitioning algorithm for VLSI circuit design. The performance of multilevel partitioning algorithms that are proposed to enhance the performance of previous iterative-improvement partitioning algorithms for large scale circuits, depend on choice of construction methods for partition hierarchy. As the most of previous multilevel partitioning algorithms forces experimental constraints on the process of hierarchy construction, the stability of their performances goes down. The lack of stability causes the large variation of partition results during multiple runs. In this paper, we minimize the use of experimental constraints and propose a new method for constructing partition hierarchy. The proposed method clusters the cells with the connection status of the circuit. After constructing the partition hierarchy, a partition improvement algorithm, HYIP$^{[11]}$ using hybrid bucket structure, unclusters the hierachy to get partition results. The experimental results on ACM/SIGDA benchmark circuits show improvement up to 10-40% in minimum outsize over the previous algorithm $^{[3] [4] [5] [8] [10]}$. Also our technique outperforms ML$^{[10]}$ represented multilevel partition method by about 5% and 20% for minimum and average custsize, respectively. In addition, the results of our algorithm with 10 runs are better than ML algorithm with 100 runs.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.4
• /
• pp.19-29
• /
• 2009

In this study, a numerical analysis was performed to predict the sequential behavior of anchored retaining wall where the failure accident took place, and verified accuracy of prediction through the comparisons between prediction and field measurement. The emphasis was given to the wall behaviors and the variation of sliding surface based on the two different methods of elasto-plastic and finite element (shear strength reduction technique). Through the comparison study, it is shown that the bending moment and the soil pressure at construction stages produce quite similar results in both the elasto-plastic and finite element method. However, predicted wall deflections using elasto-plastic method show underestimate results compared with measured deflections. This demonstrates that the elasto-plastic method does not clearly consider the influence of soil-wall-reinforcement interaction, so that the tension force (anchor force and earth pressure) on the wall is overestimated. Based on the results obtained, it is found that finite element method using shear strength reduction method can be effectively used to perform the back calculation analysis in the anchored retaining wall, whereas elasto-plastic method can be applicable to the preliminary design of retaining wall with suitable safety factor.