• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.7 no.4
• /
• pp.209-214
• /
• 1974

The utilization dietary protein in young rainbow trout was investigated when feeded with the diets of controlled levels of casein and lipids for 12 days. The composition of the diet is shown in Table 1. Body weight gain was in proportion to the protein content in diet up to $40\%$, ana the maximum was obtained with $40.4\%$ of crude protein (Fig. 1, Table 2). On the other hand, the accumulated protein in body also showed almost maximum value around 40n of protein level in the diet and: the change of accumulated protein showed a little with more-protein level(Fig. 3, Table 9). The protein accumulation rate (protein accumulated/protein consumed) showed its highest value at about $40\%$ of protein level, while the protein utilization value (protein accumulation rate x protein content of diet) attained its highest value at $54.8\%$ of protein level (Table 3). With the above results it is observed that the requirement of dietary protein for young rainbow trout is about $40\%$ of protein in the diet when casein is used as the sole protein source. In protein efficiency ratio (PER) the lower protein level in the diet, the higher PER yields and the more the quantity of protein increases, the more PER decreases and its relation could be figured out as an equation of y=4.91-0.034x (Fig.4), Nose measured PER utilizing the diet which result of this, it is reported that PER rate of casein dropped within the extent of $25\%$ protein in diet. The reason why such a different PER rate appeared at the low protein level is revealed as the carbohydrate is low but the lipid high in capacity of utililzing nutrients for rainbow trout. The relation between the protein content of diet and the conversion factor, feed efficiency were determined and the results are shown in Fig. 2.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.10
• /
• pp.6604-6610
• /
• 2015

In this paper, an efficient Wireless Access in Vehicular Environment (WAVE) packet transmission scheme for railroad communication is proposed. WAVE communication is a wireless local area network (WLAN) based communication and it is developed to be suitable for vehicular communication. There has been a lot of study on WAVE's applicability to Intelligent Transport System (ITS). As one of main transportation methods, by using WAVE, quality of railroad communication including WLAN based Communication Based Train Control (CBTC) can be enhanced and variety of railroad communication systems can be integrated into WAVE. However, there are technical challenges to adopt WAVE in railroad communications. For the simplest single-PHY WAVE, time division alternation of 50ms between Control Channel (CCH) and Service Channel (SCH) is required. Since there are delay sensitive railroad traffic types, alternation operation of CCH and SCH may cause performance degradation. In this paper, after identifying a couple of problems based on detailed analysis, a novel packet transmission scheme under railroad environment is proposed. In order to verify if the proposed scheme meets the requirement of railroad communication, WAVE transmission is mathematically modeled.

• Journal of Korea Technology Innovation Society
• /
• v.20 no.2
• /
• pp.368-386
• /
• 2017

The purpose of this study is to present the technology value model based on profit approach and IITP practical guide for Ethernet network technology, which is the core technology of autonomous vehicles and connected cars in the hyper-connected industry. In-vehicle network, Ethernet technology, Ethernet port count, port pricing, and application data for technology assessment are sources of global market research organizations. The data on the company's COGS (Cost of Goods Sold), operating capital requirement, capital expenditure, and income statement data are used by the Bank of Korea's Business Analysis Report. According to the results of the study, the product market size was estimated to be US $470.3 billion and the technology market size was $52.1 billion over the seven years of economic life cycle of technology. The market value of the technology was estimated to be $260 million reflecting the possibility of entry into the market. In the case of the corporate management analysis report, the average value of the IITP and the top 25% were $0.7 million and $40.2 million, respectively. -27.8 million, and -73.6 million dollars respectively. This implies that government support for policy support is needed when conducting corporate R&D with high cost-to-sales ratio. The results of this study can be used as a reference for the evaluation of technology demand based ICT R&D technology in the industrial internet market in the fourth industrial revolution era.

• Journal of radiological science and technology
• /
• v.38 no.4
• /
• pp.331-336
• /
• 2015

Medical electrical equipment - Part 1: General requirement for basic safety and essential performance of MFDS was revised as 3th edition and Medical electrical equipment Part 2-54: Particular requirements for the basic safety and essential performance of X-ray equipment will be expected to be announced as notification. Therefore this technical report was written to introduce provision of the particular requirements, replacement, addition, amendment. The purpose of this particular requirements is to secure requirements for basic safety and essential performance of X-ray equipment for radiography and radioscopy. X-ray high voltage generator, mechanical protective device, protection against radiation is included in this particular requirements. Medical electrical equipment - Part 1, Part 1-2, Part 1-3 is applied to this particular requirements. If the requirements is announced as notification, It is expected to widen understanding for basic safety and essential performance of X-ray equipment for radiography and radioscopy and play a part to internationalize of medical equipments.

• Proceedings of the Korean Society of Developmental Biology Conference
• /
• 2009.02a
• /
• pp.49-57
• /
• 2009

The cloning of canids was succeeded in 2005, several years after the birth of Dolly the sheep and also after the cloning of numerous other laboratory and farm animal species. The delay of successful somatic cell nuclear transfer (SCNT)was due to the unique reproductive characteristics of the female dogin comparison to other domestic mammals, such as ovulation of immature canine oocyte and a requirement of 25 days for the completion of meiosis within the oviduct (Holst & Phemister, 1971). When the technology for the recovery of in vivo matured oocyte was established, the application of cloning also became possible and cloned dog offspring were obtained. This report summarizes the progress of technical procedures that are required for cloning canids and the application of this technique. The first cloned dog, Snuppy, was achieved using an in vivo-matured oocyte which was enucleated and transferred with an adult skin cell of male Afghan hound. After establishment of a criterion of well-matured oocyte for the improvement of SCNT efficiency, we obtained three cloned female Afghan hound and a toy poodle cloned from 14 year-old aged Poodle using SCNT through this factor. To date, cloned dogs appeared to be normal and those that have reached puberty have been confirmed to be fertile. Through application of canine SCNT technique, first, we demonstrated that SNCT is useful for conserving the breed of endangered animal from extinction through cloning of endangered gray wolves using inter-species SCNT and keeping the pure pedigree through the cloning of Sapsaree, a Korean natural monument. Secondly, we showed possibility of human disease model cloned dog and transgenic cloned dog production through cloning of red fluorescent protein expressing dog. Finally, SCNT can be used for the propagation of valuable genotypes for making elite seed stock and pet dog. In summary, dog cloning is a reproducible technique that offers the opportunity to preserve valuable genetics and a potential step towards the production of gene targeted transgenic cloned dogs for the study of human diseases.

• Korean Journal of Clinical Laboratory Science
• /
• v.38 no.3
• /
• pp.184-188
• /
• 2006

The purpose of the recovery experiment in clinical chemistry is performed to estimate proportional systematic error. We must know all measurements have some error margin in measuring analytical performance. Proportional systematic error is the type of error whose magnitude increases as the concentration of analyte increases. This error is often caused by a substance in the sample matrix that reacts with the sought for analyte and therefore competes with the analytical reagent. Recovery experiments, therefore, are used rather selectively and do not have a high priority when another analytical method is available for comparison purposes. They may still be useful to help understand the nature of any bias revealed in the comparison of kit experiments. Recovery should be expressed as a percentage because the experimental objective is to estimate proportional systematic error, which is a percentage type of error. Good recovery is 100.0%. The difference between 100 and the observed recovery(in percent) is the proportional systematic error. We calculated the amount of analyte added by multiplying the concentration of the analyte added solution by the dilution factor(mL standard)/(mL standard + mL specimen) and took the difference between the sample with addition and the sample with dilution. When making judgments on method performance, the observed that the errors should be compared to the defined allowable error. The average recovery needs to be converted to proportional error(100%/Recovery) and then compared to an analytical quality requirement expressed in percent. The results of recovery experiments were total protein(101.4%), albumin(97.4%), total bilirubin(104%), alkaline phosphatase(89.1%), aspartate aminotransferase(102.8), alanine aminotransferase(103.2), gamma glutamyl transpeptidase(97.6%), creatine kinase(105.4%), lactate dehydrogenase(95.9%), creatinine(103.1%), blood urea nitrogen(102.9%), uric acid(106.4%), total cholesterol(108.5), triglycerides(89.6%), glucose(93%), amylase(109.8), calcium(102.8), inorganic phosphorus(106.3%). We then compared the observed error to the amount of error allowable for the test. There were no items beyond the CLIA criterion for acceptable performance.

• Resources Recycling
• /
• v.22 no.3
• /
• pp.73-80
• /
• 2013

Metal prices are rapidly rising due to increasing demand of metals and limited available resources according to the industrial requirement. As a result, securing a stable supply of these metal resources has been recognized as a core element of national competitiveness and sustained economic growth. In the case of magnesium and its alloys which are entirely depending on import, low-grade magnesium scraps from end-of-life vehicles and 3C(Camera, Computer, Communication) parts and magnesium wastes such as sludge and dross generated during melting process are hardly recycled. Accordingly, the development and commercialization of recycling technology of low-grade magnesium scrap is desperately needed to improve efficiency of resource circulation and to establish the required proprietary of resource metal supply and demand. In this study, papers and patents on recycling technologies of waste magnesium were analyzed. The range of search was limited in the open patents of USA (US), European Union (EP), Japan (JP), Korea (KR) and SCI journals from 1974 to 2012. Patents and journals were collected using key-words searching and filtered by filtering criteria. The trends of the patents and journals was analyzed by the years, countries, companies, and technologies.

• Journal of radiological science and technology
• /
• v.33 no.4
• /
• pp.387-394
• /
• 2010

In the field of healthcare, the conventional sterilization treatments have been replaced by irradiation methods which are in accordance with internationally well established quality standards. The quality control in radiation sterilization assures that the absorbed dose of the irradiated material is in agreement with its requirements and standards. The electron beam irradiation requires technical assessments of more process parameters than gamma irradiation does. Korea has witnessed wide uses of electron accelerators since early 2000 but there hasn't been research experiences relating to quality system in accordance with international standards. The new large scale e-beam irradiation system with the specification of 10 MeV, 8 kW was installed and operated in 2008 by Seoul Radiology Services Co. It consists of the electron accelerator, product handling system, safety, documentation and control subsystems into an integrated system to meet the requirement of the Good Manufacturing Practice such as process quality assurance and management of product tracking records. To implement the international standard such as EN ISO11137, it is necessary to understand the purposes aimed in the standard and carry out the tests following the procedures required. This study presented the specification of the e-beam facility and showed what its design requirements and features are. The test results on a variety of process parameters were presented and validated it they are within the required limits.

• Korean Journal of Remote Sensing
• /
• v.26 no.2
• /
• pp.277-285
• /
• 2010

Geostationary Ocean Color Imager(GOCI-I), the world's first space-borne ocean color observation geostationary satellite, will be launched on June 2010. Development of GOCI-I took about 6 years, and its expected lifetime is about 7 years. The mission and user requirements of GOCI-II are required to be defined at this moment. Because baseline of the main mission of GOCI-II must be defined during the development time and early operational period of GOCI-I. The main difference between these missions is the global-monitoring capability of GOCI-II, which will meet the necessity of the monitoring and research on climate change in the long-term. The user requirements of GOCI-II will have higher spatial resolution, $250m{\times}250m$, and 12 spectral bands to fulfill GOCI-I's user request, which could not be implemented on GOCI-I for technical reasons. A dedicated panchromatic band will be added for the nighttime observation to obtain fishery information. GOCI-II will have a new capability, supporting user-definable observation requests such as clear sky area without clouds and special-event areas, etc. This will enable higher applicability of GOCI-II products. GOCI-II will perform observations 8 times daily, the same as GOCI-I's. Additionally, daily global observation once or twice daily is planned for GOCI-II. In this paper, we present an improved development and organization structure to solve the problems that have emerged so far. The hardware design of the GOCI-II will proceed in conjunction with domestic or foreign space agencies.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.759-767
• /
• 2021

Most weapons systems that are Force Integration are expensive equipment that reflects the latest technology, and the operation and maintenance cost is increasing continuously. Factors that efficiently operate and maintain these weapon systems include maintenance plans, economic costs, and repair part requirements. Among them, predicting the repair parts requirements during the life cycle in advance is an important way to increase operation and maintenance cost efficiency and operating availability. The start of requirement analysis for repair parts is a calculation of the CSP (CSP: Concurrent Spare parts, CSP hereafter) that is distributed when the weapon system is deployed. The CSP is an essential component of achieving the operating availability during this period because the weapon system aims to successfully perform a given operation mission without resupply for an initial set period. In the present study, the CSP calculation method was analyzed, reflecting the failure rate and operating time of items, but the analyzed CSP was aimed at preparing for technical failure, but in the initial operating environment, it is limited in coping with unexpected failures caused by human error. The failure is not included in the scope of free maintenance and is a serious factor in making the weapon system inoperable during the initial operation period. To prevent the inoperable status of a weapon system, CSP that considers human error is required in the initial operating environment, and the calculation criteria and measures are proposed.