• Journal of Electrical Engineering and Technology
• /
• v.10 no.1
• /
• pp.128-137
• /
• 2015

A novel parallel three-level zero voltage switching (ZVS) DC converter is presented for medium voltage applications. The proposed converter includes three sub-circuits connected in parallel with the same power switches to share load current and reduce the current stress of passive components at the output side. Thus, the size of the output chokes is reduced and the switch counts in the proposed converter are less that in the conventional parallel three-level DC/DC converter. Each sub-circuit combines one half-bridge converter and one three-level converter. The transformer secondary windings of these two converters are connected in series in order to reduce the size of output inductor. Due to the three-level circuit topology, the voltage stress of power switches is equal to $V_{in}/2$. Based on the resonant behavior by the output capacitance of power switches and the leakage inductance (or external inductance) at the transition interval, each switch can be turned on under ZVS. Finally, experiments based on a 2 kW prototype are provided to verify the performance of the proposed converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.3
• /
• pp.247-255
• /
• 2013

In this paper, a soft switching DC-DC converter for AC module type photovoltaic (PV) module integrated converter is proposed. A push-pull converter is suitable for a low voltage PV AC module system because the step-up ratio of a high frequency transformer is high and the number of primary side switches is relatively small. However, the conventional push-pull converters do not have high efficiency because of high switching losses by hard switching and transformer losses (copper and iron losses) by high turns-ratio of the transformer. In the proposed converter, primary side switches are turned on at zero voltage switching (ZCS) condition and turned off at zero current switching (ZVS) condition through parallel resonance between secondary leakage inductance of the transformer and a resonant capacitor. Therefore the proposed push-pull converter decreases the switching loss using soft switching of the primary switches. Also, the turns-ratio of the transformer can be reduced by half using a voltage-doubler of secondary side. The theoretical analysis of the proposed converter is verified by simulation and experimental results.

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.3
• /
• pp.9-17
• /
• 2020

In this paper, as part of the research for the infrastructure of very high flexible and reconfigurable data center using very high speed crossbar switches, we developed a simulator that can model two and three dimensional connection structure of switches with an efficient control algorithm using software defined network and verified the functions and analyzed the performance accordingly. The simulator consists of a control module and a switch module that was coded using Python language based on the Mininet and Ryu Openflow frameworks. The control module dynamically controls the operation of switching cells using a shortest multipath algorithm to calculate efficient paths adaptively between configurable computing resources. Performance analysis by using the simulator shows that the three-dimensional switch architecture can accommodate more hosts per port and has about 1.5 times more successful 1:n connections per port with the same number of switches than the two-dimensional architecture. Also simulation results show that connection length in a 3-dimensional way is shorter than that of 2-dimensional way and the unused switch ratio in a 3-dimensional case is lower than that of 2-dimensional cases.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.9
• /
• pp.4529-4548
• /
• 2016

DDoS attacks have had a devastating effect on the Internet, which can cause millions of dollars of damage within hours or even minutes. In this paper we propose a practical dynamic defense approach that overcomes the shortage of static defense mechanisms. Our approach employs a group of SDN-based proxy switches to relay data flow between users and servers. By substituting backup proxy switches for attacked ones and reassigning suspect users onto the new proxy switches, innocent users are isolated and saved from malicious attackers through a sequence of remapping process. In order to improve the speed of attacker segregation, we have designed and implemented an efficient greedy algorithm which has been demonstrated to have little influence on legitimate traffic. Simulations, which were then performed with the open source controller Ryu, show that our approach is effective in alleviating DDoS attacks and quarantining the attackers by numerable remapping process. The simulations also demonstrate that our dynamic defense imposes little effect on legitimate users, and the overhead introduced by remapping procedure is acceptable.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.215-221
• /
• 2016

In this thesis we introduce a large quantity of input interface system using a low cost single chip microcontroller which is consists of walking board with 1600 switches, RS485 communication for switch data communication and PC application software for walking pattern analysis. When a pedestrian walks on the walking board, the pattern analysis of foot pressed switches can be utilized on diverse divisions of sports and industry such as walking physical therapy, dancing, a large quantity of sensors interface system, etc.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1507_1508
• /
• 2009

This study proposes a composite right/left-handed transmission line (CRLH-TL) that permits switching between the right-handed (RH) and left-handed (LH) modes using single crystalline silicon (SCS) RF MEMS switches. It is possible to change modes from the RH to LH mode, or vice versa, by controlling the admittance of capacitors and the impedance of inductors using switch operations. The proposed switchable CRLH-TL consists of SCS RF MEMS switches, metal-insulator-metal (MIM) capacitors and shunt inductors. At 8 GHz, the fabricated device shows a phase response of $87^{\circ}$ with an insertion loss of 2.7 dB in the LH mode, and a phase response of $-77^{\circ}$ with an insertion loss of 0.56 dB in the RH mode.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.723-727
• /
• 2004

A new high-performance and low cost single switch energy recovery display driver for an AC plasma display panel (PDP) is proposed. Since it is composed of only one auxiliary power switch, two small inductors, and eight diodes compared with the conventional circuit consisting of four auxiliary power switches, two small inductors, eight power diodes, and two external capacitors, it features a much simpler structure and lower cost. Nevertheless, since the rootmean-square (RMS) value of the inductor current is very small, it also has very desirable advantages such as n low conduction loss and high efficiency. Furthermore, there are no serious voltage-drops caused by the large gas-discharge current with the aid of the discharge current compensation, which can also greatly reduce the current flowing through power switches and maintain the panel to light at n lower sustaining voltage. In addition, all main power switches are turned on under the zero-voltage switching (ZVS) and thus, the proposed circuit has a improved EMI, increased reliability, and high efficiency. Therefore, the proposed circuit will be well suited to the wall hanging PDP TV. To confirm the validity of the proposed circuit, circuit operations, features,and design considerations are presented and verified experimentally on a 6-inch PDP, 50kHz-switching frequency, and sustaining voltage 141V based prototype.

• Proceedings of the KIEE Conference
• /
• 2000.07a
• /
• pp.537-540
• /
• 2000

The Distribution System consist of many tie-line switches and sectionalizing switches, operated a radial type. When an outage occurs in Distribution System, outage areas are isolated by system switches, has to restored as soon as possible. At this time, system operator have to get a information about network topology for service restoration of outage areas. Therefore, the searching result of restorative topology has to fast computation time and reliable result topology for to restore a electric service to outage areas, equal to optimal switching operation problem. So, the problem can be defined as combinatorial optimization problem. The service restoration problem is so important problem which have outage area minimization, outage loss minimization. Many researcher is applying to the service restoration problem with various techniques. In this paper, advanced Dijkstra algorithm is applied to searching a restoration topology, is so efficient to searching a shortest path in graph type network. Additionally, fuzzy rules and operator are applied to overcome a fuzziness of correlation with input data. The present technique has superior results which are fast computation time and searching results than previous researches, demonstrated by example distribution model system which has 3 feeders, 26 buses. For a application capability to real distribution system, additionally demonstrated by real distribution system of KEPCO(Korea Electric Power Corporation) which has 8 feeders and 140 buses.

• Progress in Superconductivity
• /
• v.6 no.1
• /
• pp.7-12
• /
• 2004

Due to the very fast switching speed of Josephson junctions, superconductive digital circuit has been a very good candidate fur future electronic devices. High-speed and Low-power microprocessor can be developed with Josephson junctions. As a part of an effort to develop superconductive microprocessor, we have designed an RSFQ 4-bit ALU (Arithmetic Logic Unit) in a pipelined structure. To make the circuit work faster, we used a forward clocking scheme. This required a careful design of timing between clock and data pulses in ALU. The RSFQ 1-bit block of ALU used in this work consisted of three DC current driven SFQ switches and a half-adder. We successfully tested the half adder cell at clock frequency up to 20 GHz. The switches were commutating output ports of the half adder to produce AND, OR, XOR, or ADD functions. For a high-speed test, we attached switches at the input ports to control the high-speed input data by low-frequency pattern generators. The output in this measurement was an eye-diagram. Using this setup, 1-bit block of ALU was successfully tested up to 40 GHz. An RSFQ 4-bit ALU was fabricated and tested. The circuit worked at 5 GHz. The circuit size of the 4-bit ALU was 3 mm ${\times}$ 1.5 mm, fitting in a 5 mm ${\times}$ 5 mm chip.

• ETRI Journal
• /
• v.34 no.1
• /
• pp.1-8
• /
• 2012

This paper proposes a reconfigurable beam-steering antenna using a bended dipole and a loop. The radiation patterns of the two antennas are cancelled or compensated, and headed towards a specific direction when the dipole and loop antenna are combined at a reasonable ratio. The proposed antenna can steer the beam directions by controlling the operation of two artificial switches. The proposed antenna was manufactured on a PCB (FR-4) and a flexible PCB (polyimide). In the case of the antenna that was fabricated on a PCB, the maximum beam directions were $+50^{\circ}$, $0^{\circ}$, and $-50^{\circ}$ in the azimuth direction using the two artificial switches, and the antenna gain was 1.96 dBi to 2.48 dBi in the operation bandwidth of 2.47 GHz to 2.53 GHz. Also, the antenna was fabricated on a flexible PCB and measured under various bending conditions for wearable applications.