• Membrane and Water Treatment
• /
• v.3 no.1
• /
• pp.35-49
• /
• 2012

In membrane processes, various agents are used to enhance, protect, and recover membrane performance. Applying these agents in membrane modification could potentially be considered as a simple method to improve membrane performance without additional process. Citric acid (CI) and sodium bisulfite (SB) are two chemicals that are widely used in membrane feed water pretreatment and cleaning processes. In this work, preadsorptions of CI and SB were developed as simple methods for polysulfone ultrafiltration membrane modification. It was found that hydrogen bonding and Van Der Waals attraction could be responsible for the adsorptions of CI and SB onto membranes, respectively. After modification with CI or SB, the membrane surfaces became more hydrophilic. Membrane permeability improved when modified by SB while decreased a little when modified by CI. The modified membranes had an increase in PEG and BSA rejections and better antifouling properties with higher flux recovery ratios during filtration of a complex pharmaceutical wastewater. Moreover, membrane chlorine tolerance was elevated after modification with either agent, as shown by the mechanical property measurements.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1999.07a
• /
• pp.115-115
• /
• 1999

In this work a new process was developed for the sulfonation of the chemicallly stable engineering polymer polyethersulfone as membrane materials for electrodialysis or a flow battery applications. Commercially available polyethersulfone polymer was partially sulfonated using a CSA sulfonating agent in a dichloromethane solvent, which sulfonated polyethersulfone with various sulfonation levels have been prepared. Sulfonated polyethersulfone (SPES) membranes with different ion capacities were prepared for the purpose of identifying cation exchange membrane properties, in an attempt to find a low cost replacement for Nafion, which most of the perfluorinated membranes, known to exhibit a prolonged service life, are expensive and difficult to process. The following features were determined: the degree of sulfonation, water uptake, thermal analysis, and electrochemical properties such as ion exchange capacities, resistivity, selectivity of ion permeation. The surface of the cation exchange membranes, decomposed with the H202-treatment, were observed by using scanning electron microscope. The area resistivities of SPES mebranes in 5N-NaOH decreased from $2,150{\;}{\Omega}-cm2$ to less than $15{\Omega}-cm2$ as the ion exchange capacity (IEC) increased from 0.62 to 1.73 millieequivlants per dry gram(meq/dg).eq/dg).

• Conservation Science in Museum
• /
• v.11
• /
• pp.49-52
• /
• 2010

A wooden Comb excavated at Shinchang-dong wetland site was treated with cetylalcohol as a reinforcing agent. The conservation process was done by freeze drying the wooden artifact after substituting it with no.3 butyl alcohol and impregnating with 40wt% cetylalcohol solution. Consequently there was no noticeable surface damage. Also it showed 54% of remaining weight and a shrinkage of length 3.3%, width 2.1% and thickness 3.1%. Therefore using cetylalcohol for conservation of waterlogged archeological wood was effective dimensional stability and remaining weight.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.81-82
• /
• 2022

Al and Zn are used to protect the steel structures from corrosion. In the present studies, 15Al-85Zn alloy wires has been used for the deposition of coating by arc thermal spray process. Moreover, this process of coating exhibited severe defects formation, therefore, this coating was post-treated with different concentrations i.e. 0.05, 0.1 and 0.5M sodium hexa meta phosphate (Na6[(PO3)6]: SHMP) to fill to defects of deposited coatings and assessed their corrosion resistance in 3.5 wt.% NaCl solution with exposure periods. After the treatment, the porosity of the coating reduced significantly by formation of composite oxide films onto the coating surface. Initially, 0.5 M SHMP treated coating exhibited highest in total impedance due to significant reduction of porosity but once the exposure periods are extended, the composite oxides are dissolved, thus, total impedance is decreased.

• Membrane and Water Treatment
• /
• v.13 no.2
• /
• pp.105-110
• /
• 2022

Al₂O₃ positively charged nanofiltration composite membrane was successfully prepared with aluminate coupling agent (ACA) as modifier, sodium bisulfite (NaHSO₃) and potassium persulfate (K₂S₂O₈) as initiator and methacryloyloxyethyl trimethylammonium chloride (DMC) as crosslinking monomer. The surface of the membrane before grafting and after polymerization were characterized by SEM and FT-IR. Three factor and three-level orthogonal experiments were designed to explore the optimal conditions for membrane preparation, and the optimal group was successfully prepared. The filtration experiments of different salt solutions were carried out, and the retention molecular weight was determined by polyethylene glycol (PEG). The results showed that the polymerization temperature had the greatest effect on the rejection rate, followed by the reaction time, and the concentration of DMC had the least effect on the rejection rate. The rejection rates of CaCl₂, MgSO₄, NaCl and Na₂SO₄ in the optimal group were 83.8%, 81.3%, 28.1% and 23.6% (average value), respectively. The molecule weight cut-off of 90% (MWCO) of the optimal group was about 460, which belongs to nanofiltration membrane.

• Clean Technology
• /
• v.19 no.3
• /
• pp.264-271
• /
• 2013

In this study, we optimized the removal condition of contaminants attached on the scrap surface to recycle the scrap generated from the Zr alloy tube manufacturing process back to the nuclear grade. The main contaminant is remnant of watersoluble cooling lubricant that is used in the pilgering manufacture during the tube production, and it is assumed to be compressed and carbonized on the surface of tube. Zirlo alloy tube of ${\phi}9.50mm$, which has high occurrence frequency of scrap, was selected as the object to be cleaned, and cleaning abilities of reagents were evaluated by measuring the characteristics of contaminants remained and by analyzing the surface of the tube after cleaning process. For evaluation of each cleaning agent, we selected two types of sodium hydroxide series and three types of potassium hydroxide series. Furthermore, to confirm dependence on tempe-rature and ultrasonic intensities, cleaning at the room temperature, $40^{\circ}C$, and $60^{\circ}C$ was conducted, and results showed that higher the cleaning temperature and higher the ultrasonic intensity, better the cleaning effect. As a result of the bare-eye inspection, while the use of sodium hydroxide provided satisfactory condition on the tube surface, the use of potassium hydroxide series provided satisfactory condition on the tube surface only when the ultrasonic intensity was over 120 W. In the cleaning effect analysis using the gravimetric method, cleaning efficiency of sodium hydroxide series was as high as 97.6% ($60^{\circ}C$, 120 W), but since the tube surface condition was poor after the use of potassium hydroxide, the gravimetric method was not appropriate. In the analytical result of surface contaminants on the tube surface, C, O, Ca, and Zr were detected, and mainly C and O dominated the proportion of contaminants. It was also found that the degree of cleaning on the tube affected the componential ratio of C and O; if the degree of cleaning is high, or if cleaning is well-conducted, the proportion of C is decreased, and the proportion of O is increased. Based on these results, optimal cleaning for application in the industry can be expected by categorizing cleaning process into three steps of Alkali cleaning, Rinsing, and Drying and by adjusting cleaning parameters in each step.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.36 no.1
• /
• pp.38-45
• /
• 2009

The aim of this study was to examine efficacy of the commercially available 10% CPP-ACP cream (Tooth mousse, GC Co., Japan) and/or 0.05% NaF solution on the remineralization of artifical caries-like lesion in the bovine teeth enamel. Sixty bovine teeth were embedded in orthodontic resin and flattened. The enamel surface in 3 mm diameter was exposed with nail varnish. Specimens were stored in demineralizing solution and divided 5 groups; Group 1 (No treatment), 2 (0.05% NaF solution 1 min), 3 (Tooth mousse 3 min), 4 (After 0.05% NaF solution, Tooth mousse treatment), and 5 (After Tooth mousse treatment, soaking in 0.05% NaF solution during 1 min). After treatment by groups, all specimens was stored in artificial saliva for 30 min. After the process described as above was performed during 10 days without pH cycling, surface hardness (Vickers Hardness Number, VHN) was tested and analyzed by paired t-test and one-way ANOVA test with SPSS 14.0. In intragroup comparison between surface hardness of pre and post-treatment, group 3, 4, 5 showed statistically significant increase (P < 0.05). In intergroup comparison among surface hardness increase of all groups, difference of group 5 between pre and post-treatment ($15.80{\pm}12.21$) was the highest, and followed by group 4 ($14.27{\pm}11.73$), 3 ($4.05{\pm}5.18$), 2 ($1.15{\pm}6.83$), 1 ($0.78{\pm}6.21$). Tooth mousse can be a good alternative agent for the fluoride, and the combination use with fluoride might have the additional anticariogenic effect.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.2
• /
• pp.94-100
• /
• 2016

PURPOSE. To evaluate the effects of hydrogen peroxide pretreatment and heat activation of silane on the shear bond strength of fiber-reinforced composite posts to resin cement. MATERIALS AND METHODS. The specimens were prepared to evaluate the bond strength of epoxy resin-based fiber posts (D.T. Light-Post) to dual-curing resin cement (RelyX U200). The specimens were divided into four groups (n=18) according to different surface treatments: group 1, no treatment; group 2, silanization; group 3, silanization after hydrogen peroxide etching; group 4, silanization with warm drying at $80^{\circ}C$ after hydrogen peroxide etching. After storage of the specimens in distilled water at $37^{\circ}C$ for 24 hours, the shear bond strength (in MPa) between the fiber post and resin cement was measured using a universal testing machine. The fractured surface of the fiber post was examined using scanning electron microscopy. Data were analyzed using one-way ANOVA and post-hoc analysis with Tukey's HSD test (${\alpha}=0.05$). RESULTS. Silanization of the fiber post (Group 2) significantly increased the bond strength in comparison with the non treated control (Group 1) (P<.05). Heat drying after silanization also significantly increased the bond strength (Group 3 and 4) (P<.05). However, no effect was determined for hydrogen peroxide etching before applying silane agent (Group 2 and 3) (P>.05). CONCLUSION. Fiber post silanization and subsequent heat treatment ($80^{\circ}C$) with warm air blower can be beneficial in clinical post cementation. However, hydrogen peroxide etching prior to silanization was not effective in this study.

• Journal of Adhesion and Interface
• /
• v.16 no.4
• /
• pp.137-145
• /
• 2015

This study aimed to develop epoxy putty as a multi-purpose connection and restoration material that can be used for material-specific restoration work such as metal, wood, ceramics, earthenware and stone artifacts by replacing synthetic resins currently being used for preservation treatment of cultural assets. Existing synthetic resins have the issue of cutting force resulting from high strength, deflection resulting from long hardening time, contaminating the surface of artifacts through staining on tools or gloves and need for re-treatment resulting from material discoloration. Accordingly, paste type restoration material most widely being used in the field of cultural assets preservation treatment was selected and examined the property to select it as an object of comparison. Based on such process, epoxy putty was developed according to the kind of agent, hardener and filler. For the purpose of solving the issues of existing material and allowing the epoxy putty developed to have similar property, property experiments were conducted by selecting agents and hardeners with different characteristics and conditions. The study findings showed that both kinds are paste type that improved work convenience and deflection issue as a result of their work time of within 5~10 minutes that are about 3~10 times shorter than that of existing material. In regards to wear rate for increasing cutting force, it improved by about 3 times, thereby allowing easy molding. For the purpose of improving the issue of surface contamination that occurs during work process, talc and micro-ballon were added as filler to reduce the issue of stickiness and staining on hand. Furthermore, a multi-purpose restoration material with low shrinkage, low discoloration and high cutting force was developed with excellent coloring, lightweight and cutting force features.

• Current Research on Agriculture and Life Sciences
• /
• v.31 no.3
• /
• pp.193-199
• /
• 2013

This study dyed rayon fabric using loess as a natural colorant. To obtain the optimal dyeing conditions, various dyeing conditions were examined (temperature, pH, time, and concentration). The color fastness was evaluated using standard washing and rubbing fastness tests. The results were as follows: The loess powder particle size ranged from 0.4 to $1.7{\mu}m$ with a distribution range of 1.1 to $1.4{\mu}m$, representing a fine and uniform manufactured loess powder. The loess component analysis showed a large amount of silicon dioxide and aluminum oxide. TheFT-IR spectra showed that the ammonium group in the rayon fabric produced N-H banding at $1,540cm^{-1}$. The highest K/S value for the rayon fabric was obtained when the pH was 8.0, and this value increased rapidly with a longer dyeing time and when increasing the loess concentration to 30% (w/v). Pre-treatment with a soybean solution produced the highest K/S value for the rayon fabric with a loess concentration of 30% (w/v). The SEM analysis showed a higher amount of loess adhered to the rayon fabric surface when increasing the loess concentration. However, pre-treatment with a cationic agent and soybean solution resulted in a much higher attachment of loess to the fabric surface. Thus, the experimental results showed that using a cationized fabric and pre-treatment with a soybean solution are more effective when dyeing rayon fabric with loess than when using only loess.