• Applied Chemistry for Engineering
• /
• v.24 no.5
• /
• pp.513-517
• /
• 2013

We investigated the properties of impregnated activated carbons, a commercial adsorbent for the individual protection equipment, and examined CO adsorption and oxidation to $CO_2$. The surface area, pore volume and pore size were measured for four commercial samples using Brunauer-Emmett-Teller/Barrett-Joyner-Halenda (BET/BJH), and atomic compositions of the sample surface were analyzed based on SEM/EDS and XPS. Impregnated activated carbons containing Mn and Cu for fire showed the catalytic CO oxidation to $CO_2$ with a high catalytic activity (up to 99% $CO_2$ yield), followed by the CO adsorption at an initial reaction time. On the other hand, C: for chemical biologial and radiological (CBR) samples, not including Mn, showed a lower CO conversion to $CO_2$ (up to 60% yield) compared to that of fire samples. It was also found that a heat-treated activated carbon has a higher removal capacity both for CO and $CO_2$ at room temperature than that of untreated carbon, which was probably due to the impurity removal in pores resulted in a detection-delay about 30 min.

• Research in Plant Disease
• /
• v.15 no.1
• /
• pp.23-29
• /
• 2009

Cooking oil and yolk mixture (COY), a environmentally acceptable plant protection agent, and COY+$CaCO_3$+neem oil mixture were studied to control the powdery mildew occurring on eggplant, paprika, cherry tomato and maturity tomato in glass houses and vinyl houses during 2005 to 2007. The morphological changes of the pathogenic fungi on the leaf surface before and after treatment of COY were observed. COY made of rape seed oil and COY+$CaCO_3$+neem oil mixture were sprayed three times with 5 days interval to foliar parts of eggplant, paprika and tomato and the disease development were examined 5 days after final spray. In eggplant, the control efficacy of COY to powdery mildew was 94.6%. In paprika, the control efficacy of COY to powdery mildew was 91.6% and that of COY+$CaCO_3$+neem oil mixture was 96.2% that revealed little higher than COY itself. In tomatoes(cherry or maturity tomato), the control efficacy of COY were about 91 %, however, when COY mixture were sprayed to tomato leaves and stems the powdery mildew was controlled completely. Typical and healthy mycelia, conidiophores and condia were observed through scanning electron microscope in COY unsprayed leaf surface, on the other hand destroyed and winkled mycelia and conidiophores were observed in COY treated leaves regardless host plants nor taxonomic differences of fungi.

• Journal of Korean Society for Atmospheric Environment
• /
• v.33 no.2
• /
• pp.159-173
• /
• 2017

The Weather Research and Forecast (WRF) - Community Multiscale Air Quality (CMAQ) system was applied to investigate the influence of major point sources located in Chungcheongnam-do (CN) on surface $PM_{2.5}$ (Particulate Matter of which diameter is $2.5{\mu}m$ or less) concentrations in its surrounding areas. Uncertainties associated with contribution estimations were examined through cross-comparison of modeling results using various combinations of model inputs and setups; two meteorological datasets developed with WRF for 2010 and 2014, and two domestic emission inventories for 2010 and 2013 were used to estimate contributions of major point sources in CN. The results show that contributions of major point sources in CN to annual $PM_{2.5}$ concentrations over Seoul, Incheon, Gyeonggi, and CN ranged $0.51{\sim}1.63{\mu}g/m^3$, $0.71{\sim}1.62{\mu}g/m^3$, $0.63{\sim}1.66{\mu}g/m^3$, and $1.04{\sim}1.86{\mu}g/m^3$, respectively, depending on meteorology and emission inventory choice. It indicates that the contributions over the surrounding areas can be affected by model inputs significantly. Nitrate was the most dominant $PM_{2.5}$ component that was increased by major point sources in CN followed by sulfate, ammonium, and others. Based on the model simulations, it was estimated that primary $PM_{2.5}$ $(PPM)-to-PM_{2.5}$ conversion rates were 41.3~50.7 ($10^{-6}{\mu}g/m^3/TPY$) for CN, and 12.4~18.3 ($10^{-6}{\mu}g/m^3/TPY$) for Seoul, Incheon, and Gyeonggi, respectively. In addition, spatial gradients of PPM contributions show very steep trends. $NO_X$-to-nitrate conversion rates were 7.61~12.3 ($10^{-6}{\mu}g/m^3/TPY$) for CN, and 3.94~11.3 ($10^{-6}{\mu}g/m^3/TPY$) for the sub-regions in the SMA. $SO_2$-to-sulfate conversion rates were 4.04~5.28 ($10^{-6}{\mu}g/m^3/TPY$) for CN, and 3.73~4.43 ($10^{-6}{\mu}g/m^3/TPY$) for the SMA, respectively.

• Journal of Wetlands Research
• /
• v.22 no.3
• /
• pp.187-193
• /
• 2020

The increase in the area of impervious water due to the recent abnormal weather conditions and rapid urbanization led to a decrease in the amount of low current, resulting in an increase in the amount of surface runoff. Increased surface runoff is causing erosion, destruction of underwater ecosystems, human and property damage in urban areas due to flooding of urban river. The damage has been increasing in Korea recently due to localized heavy rains, typhoons and floods. As a countermeasure, the Busan Metropolitan Government will proceed with the creation of the Eco-Delta City waterfront zone in Busan with the aim of creating a future-oriented waterfront city from 2012 to 2023. Therefore, the current urban river conditions and precipitation data were collected by utilizing SWMM developed by the Environment Protection Agency, and the target basin was selected to simulate flood damage. Measures to reduce flood damage in various cases were proposed using simulated data. It is a method to establish a disaster prevention plan for each case by establishing scenario for measures to reduce flood damage. Considering structural and non-structural measures by performing an analysis of the drainage door with a 30-year frequency of 80 minutes duration, the expansion effect of the drainage pump station is considered to be greater than that of the expansion of the drainage door, and 8 scenarios and corresponding alternatives were planned in combination with the pre-excluding method, which is a non-structural disaster prevention measure. As a result of the evaluation of each alternative, it was determined that 100㎥/s of the pump station expansion and the pre-excluding EL.(-)1.5m were the best alternatives.

• Journal of Korean Ophthalmic Optics Society
• /
• v.10 no.1
• /
• pp.27-34
• /
• 2005

Photochromic lens is the color changing lens from colorlessness to colorness when exposed to UV light. It can protect eyes from UV-B light which cause the cataract and can be used as sunglass in the summer since it can cut off 70~80% of sun light. Surface coating technique was used to develop lens which has 70% light transmittance and of which fading time of color change is within 5 min. Various color lenses were developed so that these had various color such as blue, green, brown, violet, yellow and red etc. Lens has an excellent physical properties, 100% adhesion and 4~5H hardness. The chemical and the scratch resistance of this lens were the greatest and the thermal stability was also higher. The clinical trial of developed lens were applied to 65 patients who had photophobia by various reasons at ophthalmology of Soonchunhyang University Hospital. Results showed that glaring was significantly reduced and the visual health were remarkably improved. Especially, anti-glaring effect in the night was great for the patient who had the LASIK operation. Protection of UV-B and blue light also can prevent the patient from cataract and the yellowish crystalline lens at old ages. Through the result of clinical. trial, we know that photochromic lens could be a new technique for both cure and precaution of photophobia.

• Korean Journal of Environmental Biology
• /
• v.25 no.4
• /
• pp.313-318
• /
• 2007

Monitoring for the quality of coastal water is necessary to improve its biological resources and to maintain healthy environments. We measured the concentrations of phenols, nine polychlorinated biphenyls (PCBs), tributyltin (TBT) in surface water at 5 stations and the concentrations of mercury (Hg), chromium (Cr (VI)), cadmium (Cd), lead (Pb) in surface water of 10 stations in Tongyeong marine ranching ground of Korea in August, 2003. The concentrations of analytes were determined as follows: phenols: 1.6$\sim$2.8 ppb, PCBs: not detected (ND), Hg: <0.1 ppb, Cr (VI): 0.01$\sim$5.32 ppb, Cd: ND$\sim$0.41 ppb and Pb: 0.43$\sim$2.60 ppb. These concentrations satisfied the standards of human health protection in coastal water by Ministry of Environment, Republic of Korea as follows: phenols; 5 ppb, PCBs: 0.5 ppb, Hg: 0.5 ppb, Cr (VI): 50 ppb, Cd: 10 ppb and Pb: 50 ppb. TBT was not listed in the standards. The concentrations of Sn in TBT analyzed in sea water of Tongyeong marine ranching ground were in the range of ND$\sim$0.0273 ppb which are similar with the values of 8$\sim$35 ng Sn $L^{-1}$ (0.008$\sim$0.035 ppb) in Chinhae Bay studied by Shim et al.. Therefore, the quality of sea water in Tongyeong marine ranching ground was safe enough to protect human health.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.1
• /
• pp.45-53
• /
• 2000

To analyze the photodegradation mechanism of materials for fisheries facilities which stand for considerable time immediately under or even partly above the water surface, such as cage collar, cage net, stationary fishing gear, egc. after 900 hours exposure, weathering experiments on 3 kinds of netting twines like dyed polyethylene(PE) and nylon, and non-treated high strength PE(Hi-PE) were carried out by using xenon light source. The results obtained are as follows : It was observed by scanning electron micrograph(SEM) that a good protection by pigments was obtained in PE and nylon specimen, while crack was rapidly progressed at the surface of Hi-PE one owing to etching by UVR. There was a little increase in density resulting from reorientation of polymer chain, chain scission, etc. in Hi-PE specimen. A wide angle X-ray diffraction showed that 3 kinds of specimens had no fundamental changes in polymer crystalline structure considering each 2$\theta$ of diffraction peak. Remaining tenacity of netting twines was in order of PE, nylon, and Hi-PE after having been exposed to the effect of 900 hours. PE and nylon treated with stuffs were shown to be more resilient than non-treated Hi-PE as confirmed by SEM.

• Korean journal of applied entomology
• /
• v.47 no.2
• /
• pp.127-131
• /
• 2008

Ambrosia beetle, Platypus koryoensis, is a vector of oak wilt disease caused by Raffaelea sp. in Korea. The degree of damage by oak wilt disease was dependent on the density of the beetles in the oak trunk, a relationship between the degree of damage by oak wilt disease and the density of beetle on the basis of the number of entry hole was studied. Entry hole distribution within tree trunk was analyzed by the nearest neighbor method. Thirty four oak trees (Quercus mongolica) located in survey area were selected and then degree of damage, the number of attack hole/$623cm^2$ in upper (50cm from the surface) and lower (surface) trunk and the nearest neighbor distance between the holes were measured. The number of hole and the nearest neighbor distance in upper and lower part were positively correlated with each other. As the degree of damage was severer, the number of the holes increased, whereas the nearest neighbor distance decreased. The distribution pattern of the hole was changed from clumped one to uniform as the severity of damage increased. These results suggested that Platypus koryoensis attacked the oak tree in concentrative manner at initial stage of attack but at final stage, it distributed uniformly to reduce intraspecific competition between the beetles.

• Journal of the Korean Society of Safety
• /
• v.20 no.4 s.72
• /
• pp.171-179
• /
• 2005

It is essential to understand the role of wall lining materials when they are exposed to a fire from an ignition source. Full-scale test methods permit an assessment of the performance of a wall lining material. Fire growth models have been developed due to the costly expense associated with full-scale testing. The models require heat flux maps from the ignition burner flame as input data. Work to date was impeded by a lack of detailed spatial characterization of the heat flux maps due to the use of limited instrumentation. To increase the power of fire modeling, accurate and detailed heat flux maps from the ignition burner are essential. High level spatial resolution for surface temperature can be provided from an infrared camera. The objective of this study was to develop a heat flux mapping procedure for a room test burner flame to a wall configuration with surface temperature information taken from an infrared camera. A prototype experiment was performed using the ISO 9705 test burner to demonstrate the developed heat flux mapping procedure. The results of the experiment allow the heat flux and spatial resolutions of the method to be determined and compared to the methods currently available.

• Journal of Sensor Science and Technology
• /
• v.8 no.5
• /
• pp.414-420
• /
• 1999

The oxide sacrificial layer technology is one of the key technologies in surface micromachining. However, the commonly used aqueous HF solutions, including the $NH_4F$ buffered HF solutions (BHF), are known to attack the Al metal layers during the oxide sacrificial etch. A mixed $NH_4F$/HF/glycerine aqueous solution of 4:1:2 ratio is known to have the best etch selectivity between oxide and AI, but even this sacrificial etchant has a significant etch rate for AI. This paper reports an extensive experimental study on various concentration ratios for HF, $NH_4F$ and glycerine, and develops the optimal mixture ratio for sacrificial etching. At the $NH_4F$/HF/glycerine ratio of 2:1:4, the etch selectivity between PSG and Al improves by approximately 6 times over the previously known best selectivity, to a value of 7,700. At this condition, the measured etch rate of PSG film is approximately $2.1\;{\mu}m/min$, which is sufficiently fast. The developed sacrificial etchant allows the addition of a Al metal layer in surface micromachining, without the worry of Al layer erosion during sacrificial etch.