• Journal of Biosystems Engineering
• /
• 제42권3호
• /
• pp.136-146
• /
• 2017

Purpose: This paper presents an appropriate wrapping method by analyzing the pressure distribution applied to a bale surface, along with the change in pressure according to an increase in the number of film layers in rice straw bales, which account for 74% of the total bulky feed supply in Korea. Methods: A model with the shape of an actual bale was fabricated to analyze the distribution of surface pressure in bale wrapping, and the pressure was measured. Experiments were conducted to analyze the pressure using eight different layer numbers (2, 4, 6, 8 10, 12, 14, and 16 layers) at five wrapping speeds (27, 29, 31, 33, and 35 rpm). Results: The maximum pressure applied to a circular bale by the film occurred at the center of the end of the bale, whereas the minimum pressure occurred at the center of the bale side. An extreme value ratio between the minimum and maximum pressures was distributed as 8.5-56.6%, which was improved with an increase in rotation speed. The an uneven pressure distribution occurred because the number of film overlaps was 8.24-times greater at the center of the bale's end than at the center of the ba le side. At a level 5 rotation speed, the minimum pressure was $P_{LV5-M1}=0.0625{\sigma}^2+36.173{\sigma}-36.753$ ($R^2=0.9845$) at $M_1$, and the maximum pressure was $P_{LV5-M6}=5.5552{\sigma}^2+41.05{\sigma}-39.071$ at $M_2$, revealing a correlation of $R^2=0.9983$. Conclusions: To replace four layers with six layers, 2-4 layers were added only to the side of the bale, and the minimum pressure at $M_1$ was then improved from that at four layers to that at six layers, and the amount of film consumed for 4-6 layers was reduced by 84.6%.

• 한국분말재료학회지
• /
• 제30권2호
• /
• pp.146-155
• /
• 2023

The Ti-6Al-4V lattice structure is widely used in the aerospace industry owing to its high specific strength, specific stiffness, and energy absorption. The quality, performance, and surface roughness of the additively manufactured parts are significantly dependent on various process parameters. Therefore, it is important to study process parameter optimization for relative density and surface roughness control. Here, the part density and surface roughness are examined according to the hatching space, laser power, and scan rotation during laser-powder bed fusion (LPBF), and the optimal process parameters for LPBF are investigated. It has high density and low surface roughness in the specific process parameter ranges of hatching space (0.06-0.12 mm), laser power (225-325 W), and scan rotation (15°). In addition, to investigate the compressive behavior of the lattice structure, a finite element analysis is performed based on the homogenization method. Finite element analysis using the homogenization method indicates that the number of elements decreases from 437,710 to 27 and the analysis time decreases from 3,360 to 9 s. In addition, to verify the reliability of this method, stress-strain data from the compression test and analysis are compared.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.87-94
• /
• 2002

Most of Rapid Prototyping (RP) process adopt a solid Computer Aided Design (CAD) model, slicing into thin layers of uniform, but not necessarily constant, thickness in the building direction. Each cross-sectional layer is successive1y deposited and at the same time, bonded onto the previous layers; the stacked layers form a physical part of the model. The objective of this study is to develop a method for calculating the rotation angle ($$\theta$_x, $\theta$_y$) of hotwire of the cutting system in the three-dimensional space for the Variable Lamination Manufacturing process using expandable polystyrene foam sheet (VLM-S). In order to examine the applicability of the developed method to VLM-S, various three-dimensional shapes. such as a screw, an extruded cross, and free surface bodies such as miniatures of the monkey(a figure of Sonokong), were made using the data obtained form the method.

• Advances in nano research
• /
• 제14권2호
• /
• pp.117-126
• /
• 2023

This experimental study investigated friction stir welding (FSW) of the acrylonitrile-butadiene-styrene (ABS) T-joint in the presence of various nano-silica levels. This study aim to handle the drawbacks of the friction stir welding (FSW) of an ABS T-joint with various quantity of nanoparticles and assess the performance of nanoparticles in the welded joint. Moreover, the relationship between the nanoparticle quantity and FSW was analyzed using response surface methodology (RSM) Box-Behnken design. The input parameters were the tool rotation speed (400, 600, 800 rpm), the transverse speed (20, 30, 40 mm/min), and the nano-silica level (0.8, 1.6, 2.4 g). The tensile strength of the prepared specimens was determined by the universal testing machine. Silica nanoparticles were used to improve the mechanical properties (the tensile strength) of ABS and investigate the effect of various FSW parameters on the ABS T-joint. The results of Box-Behnken RSM revealed that sound joints with desired characteristics and efficiency are fabricated at tool rotation speed 755 rpm, transverse speed 20 mm/min, and nano-silica level 2.4 g. The scanning electron microscope (SEM) images revealed the crucial role of silica nanoparticles in reinforcing the ABS T-joint. The SEM images also indicated a decrease in the nanoparticle size by the tool rotation, leading to the filling and improvement of seams formed during FSW of the ABS T-joint.

• 대한기계학회논문집
• /
• 제19권3호
• /
• pp.771-783
• /
• 1995

A simplified model for the so-called ACRT(accelerated crucible rotation technique) Bridgman crystal growth was considered in order to investigate the principal effects of the periodic variation of angular velocity. Numerical solutions were obtained for Ro=0.5, Ra=4.236*10$_{6}$ and E=2.176*10$^{-3}$ . The effects of spin-up process combined with natural convection was investigated as a preliminary study. The spin-up time scale for the present problem was a little larger than that observed for homogeneous spin-up problems. Numerical results reveal that over a time scale of (H$^{2}$/.nu..omega.$_{f}$)$^{1}$2/ the forced convection due to the formation of Ekman layer predominates. When the state of rigid body rotation is attained, natural convection due to buoyancy emerges as the main driving force and them the steady-state is approached asymptotically. Based on our preliminary results with simple spin-up, several fundamental features associated with variation of rotation speed are successfully identified. When a periodic variation of angular velocity was imposed, the system response was also periodic. Due to effect of mixing, the heat transfer was enlarged. From the analysis of time-averaged Nusselt number along the bottom surface the effect of a periodic variation of angular velocity on the interface location could be indirectly identified.d.

• The Journal of Korean Physical Therapy
• /
• 제31권2호
• /
• pp.134-139
• /
• 2019

Purpose: This study examined the most effective exercise while performing shoulder abduction below ninety degrees. Methods: Thirty two healthy individuals (17 males, 15 females) participated and performed four exercises, 1) Posterior fly, 2) Prone row, 3) Modified prone cobra, and 4) External rotation in the prone position. Surface electromyography (sEMG) was used to measure the electrical activities for the lower, middle and upper fiber of trapezius and serratus anterior. Results: A significant difference in the muscle activities of the upper/middle/lower trapezius and serratus anterior was observed among the three different positions in terms of the PF (posterior fly), PR (prone row), and MPC (modified prone cobra) (p<0.05). In post-hoc analysis, the activities of the lower and upper trapezius were significantly higher than those of the upper trapezius and serratus anterior (p<0.05). In addition, in ERP (external rotation in prone), there was a significant difference in each activity of the muscles. Post-hoc results indicated that the upper trapezius showed greater EMG activity than the other three muscles. Conclusion: External rotation in the prone position revealed the highest activation of the lower trapezius compared to upper trapezius muscle activity. This may be particularly useful in isolating the lower trapezius in cases where excessive scapular elevation is noted. Therefore, the most effective lower trapezius exercise should be performed below ninety degrees of shoulder abduction.

• 대한기계학회논문집B
• /
• 제21권3호
• /
• pp.436-444
• /
• 1997

Three-dimensional conjugate heat transfer and particle deposition on a circular cylinder in the OVD process are numerically investigated. Flow and temperature fields are obtained by an iterative method, and thermophoretic particle deposition is simulated. Effects of the heat conduction in the cylinder, the rotation speed of the cylinder, and the traversing speed of torch on the deposition are studied. Effects of variable properties are also included. As the conductivity of the cylinder decreases, particle deposition rate and deposition efficiency greatly decrease due to the reduced temperature gradient. The rotation of the cylinder has no significant effect on the deposition due to the small diameter of the cylinder and low speed of rotation. Since the increase of the torch speed keeps the surface low temperature, the particle deposition increases with the traversing speed.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.99-107
• /
• 1995

This paper reported research results to develop an algorithm of on-lin evaluation of surface profiles and roughness generated by turning. The developed module consisted of computer simulation of surface profiles using mechanism of cutting mark formation and cutting vibrations, and online measurement of cutting vibrations. The relative cutting vibrations between tool and worpkiece were measured through an inductance pickup at the rate of one sample per rotation of the workpiece. The sampling process was monitored using an encoder to avoid conceling out the phase lag between waves. The digital cutting signals from the Analog-to-Digital converter were transferred to the simulation module of surface profile where the surface profiles were generated. The developed algorithm or surface generation in a hard turning was analyzed through computer simulations to consider the stochastic and dynamic nature of cutting process. Cutting tests were performed using AISI 304 Stainless Steel and carbide inserts in practical range of cutting conditions. Experimental results showed good correlation between the surface profiles and roughness obtained using the developed algorithm and the surface texture measured using a surface profilemeter. The research provided the feasibility to monitor surface characteristics during tribelogical tests considering wear effect on surface texture in machining.

• 한국결정성장학회지
• /
• 제3권2호
• /
• pp.117-124
• /
• 1993

연속성장법은 crystal growth chamber의 상부에 있는 reservoir에서 원료 분말을 연속적으로 공급하면서 도가니 하부에 용융대를 형성시킨 후, 종자결정을 용융대에 dipping하여 회전시키면서 아래로 끌어내려 단결정을 성장시키는 방법이다. 본 연구에서는 연속 성장법을 이용하여 silicon 단결정을 육성시켰으며 연속성장에 영향을 미치는 인자는 critical melt level, 원료공급속도, 성장속도, graphite crucible과 gruphite susceptor의 형태, work coil의 위치에 따른 graphite susceptor의 수직온도구배, 중력과 종자결정의 회전에 의한 원심력이 용융대의 안정화에 미치는 영향과 용융액 표면에서 일어나는 소결현상에 관해 고찰하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.555-556
• /
• 2006

In recent years, the higher flatness level in wafer shape has been strictly demanded with a high integration of the semiconductor devices. It has become difficult for a conventional wafer preparing process to satisfy those demands. In order to meet those demands, surface grinding with in-feed grinder is adopted. In an in-feed grinding method, a chuck table fur fixing a semiconductor wafrr rotates on its rotation axis with a slight tilt angle to the rotation axis of a cup shaped grinding wheel and the grinding wheel in rotation moves down to grind the wafer. So, stability of the grinder structure is very important to aquire a wafer of good quality. This paper describes the features of the in-feed grinder and some FEM analysis results of the grinder structure.