• 한국표면공학회지
• /
• 제30권4호
• /
• pp.272-280
• /
• 1997

The Thermal Barrier Coation(TBC) to improve the that barrier and wear resistant propenrty in high temperature ofthe aircraftength between the accumlation of the aircraft engine and the automobile engine has usually the two layer structure. One is a creamic top layer for heat insulation and the other is a metal bond layer to facilitate the bond strength between the top ceramic layer and the substrate. But, the coated layers should be peeled off because of the accumulation of the thermal stress by the differance of the thermal expantion coefficient between metal and ceramics in a hrat cyclic environment. In this study, the intermediate layer by plasm spray process was introduced to reduce the thermal stress. The powders of plasm spray coating were the Yttria Stabilized Zirconia (YSZ), the Magnesia Stabillized Zirconia(MSZ) and NiCrAlY. the intermediate layer was sprayed with the powders of the bond cast for the purpose of test were executed. The high temperature wear resistance tends to decreasnceee wear and thermal shock test were exeucuted. The high temperature were resistance of the YSZ TBC is better that of the MSZ TBC. The wearrsistance tends to decrease accoring to incresing the temperature between $400^{\circ}C$to $600^{\circ}C$. The thermal shock life of the 3 layer TBC with YSZ top casting was the most outstanding thermal shock rsisstasnce. This means that the intermediate layer should play an importnat roll to alleviate the diffrerence of the thermal expansion coef frcients between metallic layer and cermics layer.

• Ocean and Polar Research
• /
• 제29권1호
• /
• pp.33-42
• /
• 2007

To obtain the overall distribution patterns and characteristics of the East Sea Intermediate Water (ESIW), the historical data obtained by the Japan Maizuru Marine Observatory (MMO) and the Korea Ocean Research and Development Institute (KORDI) were analyzed. To obtain water characteristics of the ESIW on isopycnal surfaces, temperature, salinity and dissolved oxygen were interpolated at every 0.01 interval of potential density. And then the interpolated values were averaged at the same potential density. This potential density average method preserved the salinity minimum layer more clearly compared to the depth average method. The potential density(${\sigma}_{\theta}$) range of the ESIW was $26.9{\sim}27.3$. The representative potential density of the ESIW was found to be 27.2, because the characteristics of the ESIW was clear at this density. From the horizontal distributions of physical properties on the isopycnal surface of $27.2{\sigma}_{\theta}$ it is suggested that the low salinity ESIW circulates anticlockwise over the whole basin with the high salinity intermediate water. The low salinity intermediate water extended from the northwestern part to the east along the sub-polar front and to the Ulleung Basin along the east coast of Korea.

• 해양환경안전학회지
• /
• 제22권1호
• /
• pp.123-128
• /
• 2016

프로펠러 표면의 생물 부착이 프로펠러 성능에 상당한 영향을 미치지만 프로펠러 표면 거칠기와 관련된 연구는 상대적으로 선체 표면에 비하여 많지 않다. 본 연구에서는 Schultz(2007)가 발표한 Granville's similarity-law scaling 절차에 기초하여 실선 7 m 크기의 탱커 프로펠러에 표면 부착물 상태가 서로 다른 3가지 경우를 고려하여 프로펠러 단독 효율의 감소의 변화를 Lifting surface code를 사용하여 수치적 계산을 수행하여 효율을 비교하였다. 본 논문에서의 결과는 표면 거칠기가 큰 석회질 부착물($k_s=0.001$)은 선박 설계 속도(J=0.5)에서 최대 15 %의 프로펠러 효율 감소를 보였음을 확인하였으며 이는 선박 운항 시 생물 부착에 의한 효율 감소에 대한 평가가 고려되어야 한다는 점을 나타내고 있다.

• 한국환경보건학회지
• /
• 제36권3호
• /
• pp.236-246
• /
• 2010

In preparative anti-corrosive coating experiments, polyaniline was obtained by reacting an oxidizing agent with the monomer aniline. Further, the primer coating was prepared using a variety of widely-used materials such as urethane resin. For the top coating, epoxy resin and acrylic urethane resin were used. Characteristics of the coatings were assessed according to KS and ASTM specifications, and the structure of the polyaniline was characterized using FT-IR and TGA. For analysis of anti-corrosive properties in salt-spray experiments, measurements of the oxidation state of iron and surface atomic analysis were conducted using XPS and SEM-EDX. Unlike general anti-corrosive coatings which exhibit anti-corrosive effects only as a primer coating, the anti-corrosive coatings using polyaniline as the anti-corrosive pigment showed a marked synergistic effect with the top coatings. In other words, the top coatings not only produce a fine view effect, but also increase, through interaction with the primer coatings, the resistance to diffusion of corrosive factors from the external environment. It was also found that, unlike the heavy metal oxide-forming layer of the passive barrier alone, the polyaniline anti-corrosive pigment oxidized iron at the interface with the iron substrate to form a passive barrier in the oxidic layer, and itself formed a potential barrier layer with anti-corrosive factors from the external environment. Although the passive layer was damaged, the damaged area did not become completely oxidized iron; on the contrary, it showed a tendency to reduction. This can be interpreted such that a passive layer is formed again on the damaged area, and that at the same time there is a tendency to self-healing.

• 한국물환경학회지
• /
• 제31권6호
• /
• pp.723-731
• /
• 2015

We investigated the spatial and temporal patterns of water quality in the Gangjung-Goryoung weir that is located in the middle area of the Nakdong river, Korea. The monitoring results indicated that there are discernible vertical differences in water quality during the pre- and post-monsoon periods (May to September). During this period, it was observed that the weak thermal stratification formed at the maximum level, and pH, Chl-a, and DO concentrations in the surface layer were higher than those in the bottom layer. This vertical difference was especially noticeable for DO concentrations: there were DO depletions at the bottom layer in late June to early August. During the summer monsoon period with heavy rainfall, there was a decline in vertical differences in water quality. From this study, it was suggested that continuous monitoring of vertical profiles could become a useful tool for identifying the spatial and temporal distributions of water quality and for developing the best management policy for water quality in the Nakdong river.

• 인간식물환경학회지
• /
• 제22권6호
• /
• pp.551-561
• /
• 2019

This study was conducted to find out differences in the removal efficiency of particulate matter (PM) depending on the type of plants and the morphological characteristics of leaves. A total of 12 plants were used, with three plants selected for each type of leaves (big leaf, small leaf, compound leaf, needle leaf). We measured the removed amount of PM10 and PM2.5, the structure of the abaxial leaf surface, and the weight of the wax layer of each plant. Plants with the high removal efficiency of PM included Pachira aquatica Aubl., Ardisia crenata, and Dieffenbachia 'Marianne', and plants with the low removal efficiency included Nandina domestica Thunb, Schefflera arboricola, and Quercus dentata. The abaxial leaf surface having a high removal efficiency of PM had many large wrinkles, and the abaxial leaf surface having a medium removal efficiency was flat and smooth. On the other hand, there were many fine hairs on the abaxial leaf surface with a low removal efficiency. According to the plant leaf type, the PM10 removal efficiency of plants with needle leaves was about three times higher than that of other plants. In particular, the wax layer of conifers weighed 6-24 times higher than those of other plants. The stomata of conifers were evenly distributed on the adaxial and abaxial leaf surfaces; however, the stomata of Sciadopitys verticillata appeared in the form of papillae unlike general stomata. Therefore, the removal efficiency of PM varied depending on the macro-, and micro-morphological characteristics of plant leaves such as the structure of the abaxial leaf surface, and the weight of the wax layer. Based on this research, selecting plants that are effective in reducing PM in consideration of the plant type and leaf characteristics will improve indoor air quality and decrease exposure of PM to human body.

• 폴리머
• /
• 제29권4호
• /
• pp.392-398
• /
• 2005

Layer-by-layer(LbL) 흡착에 의한 poly(ethylene-alt-m미? anhydride) (PEMAh)/poly(4-vinyl pyridine) (P4VP) 자기조립 다층박막을 제조하였다. 자기조립 다층막을 이루는 PEMAh/P4VP 두 고분자 사이의 수소 결합과 정전기적 인력이 다층막을 이루는 원동력이라는 것이 푸리에 변환 적외선(FT-IR) 분광분석에 의해서 확인되었다. 다층막의 균일한 자기조립 과정은 PEMAh/P4VP 이중층막의 적층 수 증가에 따른 UV-vis 스펙트럼의 256 nm에서 나타나는 P4VP 특성 흡수 피크의 선형적 증가에 의해서 확인할 수 있었다. 다층막을 이루는 고분자 전해질 담지 용액의 조건 변화가 다층막 형성에 미치는 영향을 살펴보기 위하여 두 고분자 용액의 농도 및 PEMAh 담지용액의 pH를 변화시키면서 다층막을 제조하였다. 다층막의 두께, 흡착된 고분자 전해질 질량 및 표면 거칠기의 변화를 UV-vis 분광 분석, 수정진동자 미량저울(quartz crystal microbalance;QCM) 및 원자 힘 현미경(atomic force microscopy;AFM)을 이용하여 측정하였다.

• Corrosion Science and Technology
• /
• 제4권4호
• /
• pp.121-129
• /
• 2005

Basic design concept of the future steel structure requires environmental compatibility and maintenance free capability to minimize economic burdens. Recent trends in alloy design for advanced weathering steel include addition of various alloying elements which can enhance formation of stable and protective rust layer even in polluted urban and/or high $Cl^{-}$ environment. The effects of Ca, Ni, W, and Mo addition on the corrosion property of Ca-modified weathering steel were evaluated through a series of electrochemical tests (pH measurement and electrochemical impedance spectroscopy: EIS) and structural analysis on rust layer formed on the steel surface. Ca-containing inclusions of Ca-Al-Mn-O-S compound are formed if the amount of Ca addition is over 25 ppm. Steels with higher Ca content results in higher pH value for condensed water film formed on the steel surface, however, addition of Ni, W, and Mo does not affect pH value of the thin water film. The steels containing a high amount of Ca, Ni, W and Mo showed a dense and compact rust layer with enhanced amount of ${\alpha}-FeOOH$. Addition of Ni, W and Mo in Ca-modified weathering steel shows anion-selectivity and contributes to lower the permeability of $Cl^{-}$ ions. Effect of each alloying element on the formation of protective rust layer will be discussed in detail with respect to corrosion resistance.

• Ocean and Polar Research
• /
• 제28권2호
• /
• pp.153-161
• /
• 2006

To investigate inflow path of the East Sea Intermediate Water (ESIW) into the Ulleung Basin, hydrographic data surveyed in July 2005 were analyzed. The ESIW was characterized by the Salinity Minimum Layer (SML) within a depth range of 100 to 360 meters. Averaged potential temperature and salinity of the SML were $1.835^{\circ}C$ and 34.049 psu, respectively. Mean potential density $({\sigma}_{\theta})$ of the SML was 27.221 with a standard deviation of 0.0393. On isopycnal surfaces of 27.14 and 27.18 $({\sigma}_{\theta})$ which correspond to upper layers of the ESIW, the coastal low salinity water was separated from the offshore low salinity water by the relatively warm and saline water which might be affected by the Tsushima Warm Current Water. Relatively cold and fresh water, however, intruded into the Ulleung Basin from the region of Korean coast on isopycnal surfaces of 27.22 and 27.26 which was lower layer of the ESIW. The salinity distribution in the isopycnal layer of $27.14{\sim}27.26$ with acceleration potential on 27.22 up surface also showed clearly that the low salinity water flowed from the coastal area and intruded into the Ulleung Basin. This implies that the ESIW flows ken the north to the south along the east coasts of Korea and spreads into the Ulleung Basin in summer.

• 보존과학연구
• /
• 통권29호
• /
• pp.255-278
• /
• 2008

Considering the physical quality of the wall body in this study we tried to select a replenishing that is proper for filling the cracked part of the painting wall layer and apply the natural adhesives that have traditionally been used, investigating whether it is possible to substitute those for the chemical adhesive which is used at present time. The result of this study showed the red algae adhesive was, in a weathering environment, as safe as the synthetic resin originated from the polyvinyl acetate which is used generally on the present spot, and it was concluded that although the starch adhesive displayed its superiority in enhancing the strength of the earth mortar and its work disposition, it seemed proper for it to be used as a filling adhesive for the first or midterm layer because it showed a surface hardening phenomenon. And also the glue and fish glue were judged they were not qualified as a filling adhesive due to mold occurring in a environment of high moisture that is a biological problem, showing at same time a weak physical feature in a weathering environment. Therefore it would be possible to use the red algae adhesive or starch one substituting them for the original one sold on the present market, if among natural adhesives the weak points of the them were to be corrected.