• Korean Journal of Food Science and Technology
• /
• v.17 no.3
• /
• pp.203-207
• /
• 1985

Relationship between cell surface hydrophobicity and pellicle formation was studied in a film strain isolated from stored apple wine and identified as Hansenula beijerinckii FY-5. In the media containing non-ionic surface-active agents the pellicle formation of strain FY-5 was efficiently repressed, whereas growth of the yeast was possible, and also cell surface hydrophobicity was greatly decreased by the addition of these agents. These results indicate that a pellicle formation factor, which keeps yeast cells floating on the medium surface, is necessary for the pellicle formation, and surely this factor is the hydrophobicity of the cell surface. The pellicle formation in the film strains was abundant with the increase of the cell surface hydrophobicity, whereas the non-film strains had less hydrophobicity as compared with the film strains. Ethanol, as a sole carbon source, efficiently increased hydrophobicity more than glucose, and the hydrophobicity was lowered with the rise of pH. In the experiments of time course, the hydrophobicity was increased in proportion to cell growth, and was maximum during the stationary phase.

• Journal of Microbiology and Biotechnology
• /
• v.5 no.4
• /
• pp.241-243
• /
• 1995

A lipopolysaccharide (LPS) defective mutant of Bradyrhizobium japonicum was characterized in terms of its cell surface hydrophobicity (CSH). By monitoring the kinetics of adhesion to hexadecane the LPS mutant was found to be far more hydrophobic than the wild type strain; the removal coefficients were 4.65 $min^{-1}$ for the mutant, as compared with only 2.40 $min^{-1}$ for the wild type. The possible role of cell surface hydrophobicity of B. japonicum in nodulation process is discussed.

• Journal of Environmental Science International
• /
• v.7 no.3
• /
• pp.269-274
• /
• 1998

In order to develop of support medla for bloom reactor, physicochemical properties and attachability of surface of activated carbon, clay mineral, non-clay mineral, and waste mold sand were enamined. Measured physicochemical properties of materials were surface roughness, mean particle size, surface area, hydrophobicity, and surface charge. At a tested materials, activated carbon was the best attachable material and microorganisms were attached $20.1{\times}10^7CFU/cm^2$ at surface, compared with diatomaceous earth which were attached of $9.2{\times}10^7CFU/cm^2$ in our research, surface area and hydrophobicity show- ed more Influence than any other factor on attachment of microorganisms.

• Korean Journal of Food Science and Technology
• /
• v.25 no.5
• /
• pp.571-575
• /
• 1993

Effect of surface hydrophobicity of soybean peptides on serum cholesterol in rats was investigated. Soybean protein(ISP), casein(CNP), and their peptic hydrolyzates fractionated by acid precipitations (SHT, SH8, SH6, SH4, CHT, CH6, CH5, CH4) were fed to rats and the concentration of serum cholesterol and the fecal steroid excretion were measured. And surface hydrophobicities of the peptide fractions were measured by determining by the ANS flourescence intensity and SDS binding capacity. It was found that the higher the surface hydrophobicity of peptides was, the more the fecal steroids excreted(r=0.801) and the lower the concentration of serum cholesterol became(r=-0.868). However, there was no relationship between SDS surface hydrophobicity and fecal steroids or serum cholesterol. ANS surface hydrophobicity of soybean protein was increased by enzymatic hydrolysis. These results suggest that high surface hydrophobicity of peptides formed during digestion is responsible for the hypocholestrolemic effect of soybean protein through the hydrophobic interaction between the peptides and bile salts in rats.

• Food Science of Animal Resources
• /
• v.26 no.4
• /
• pp.497-502
• /
• 2006

The adhesion of 16 bifidobacterial strains, including 10 isolates from Korea infants, to Caco-2 cells and their cell surface hydrophobicity were tested. The results of adhesion and cell surface hydrophobicity of for various bifidobacterial strains were obtained and correlations between adhesion and hydrophobicity were strain-dependent properties. Any correlations between species of tested strains were not observed. Among the tested strains, Bifidobacterim longum D6, B. longum H4, B. thermophilum ATCC 25525, B. suis ATCC 27533, and B. animalis subsp. lactis BB12 had higher adherent properties and B. bifidum B3, B. longum D6, B. longum stronger hydrophobicity, respectively. Due to the strain-dependant correlation between adhesion to Caco-2 cells and cell surface hydrophobicity of bifidobacteria, these results provide a possible method for preliminary selection of bifidobacteria potentially adherent to Caco-2 cells by means of cell surface hydrophobic properties.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.7
• /
• pp.636-641
• /
• 2000

The purpose of this study is assessing the characteristics of surface aging and recovery of hydrophobicity for silicone rubber which takes a great interest as outdoor insulation recently subjected to the combined stressed of salt fog and AC power. The methods for assessing are contact angle ATR-FRIR, AFM and XRD. In addition salt fog method is adopted as the artificial contamination experiment and AC power is applied 24 hour on and 24 hour off repeatedly for 5 cycles. The results suggest that degraded surface was more rough than virgin but was restored water repellency through the off cycle. It was due to not only the formation of fractal surface but also maintenance of hydrophobic surface by diffusion of low molecular oil. Although surface recovers initial hydropohbicity there are possibilities of decreasing electrical performance due to irreversable changes such as depolymerization of surface and loss of filler particles. This fact is confirmed by surface conductivity measurement showing that the degradation is significant and the recovery of hydrophobicity is imperfect as the energized cycle increases.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.4
• /
• pp.153-160
• /
• 2001

In order to analyze the degradation process of epoxy/glass fiber for outdoor condition, FRP laminate was exposed to high temperature. Then, the degradation process was evaluated by comparing contact angle, surface potential, surface resistivity, and XPS. The experimental results showed that the amount of weight loss, contact angle, surface potential and surface resistivity increased up to 200 $^{\circ}C$ as a function of temperature. These phenomena show the existence of hydrophobic surface. With the change to the hydrophobic surface and the electrical potential and resistivity on FRP surface increased. In XPS to analyze surface chemical structures, the increased hydrophobicity in thermal increase of unsaturated double bond in carbon chains. Aslo, thermal treatment caused the discoloration on the point of treated surface. These phenomena were attributed to the generations of ether group.

• Computers and Concrete
• /
• v.23 no.5
• /
• pp.351-359
• /
• 2019

In this study, the calcium hydroxide, an inherent product of cement hydration, was treated using biomimetic carbonation method of incorporating stearic acid to generate the hydrophobic calcium carbonate on concrete surface. Carbonation reaction was carried out at various $CO_2$ pressure and temperatures and utilizing the Scanning Electron Microscope (SEM), chloride-ion penetration test apparatus, and compression test machine to investigate the hydrophobicity, durability, and mechanical properties of the synthesized products. Experimental results indicate that the calcium stearate may change the surface property of concrete from hydrophilicity to hydrophobicity. Increasing reaction temperature can change the particles from irregular shapes to needle-rod structures with increased shear stress and thus favorable to hydrophobicity and microhardness. The contact angle against water for the concrete surface was found to increase with increasing $CO_2$ pressure and temperature, and reached to an optimum value at around $90^{\circ}C$. The maximum static water contact angle of 128.7 degree was obtained at the $CO_2$ pressure of 2 atm and temperature of $90^{\circ}C$. It was also found that biomimetic carbonation increased the permeability, acid resistance and chloride-ion permeability of the concrete material. These unique results demonstrate that the needle-rod structures of $CaCO_3$ synthetized on concrete surface could enhance hydrophobicity, durability, and mechanical properties of concrete.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.6
• /
• pp.462-468
• /
• 1999

Room temperature vulcanizing (RTV) silicone rubber has been widely used to coat porcelain insulators to render water repellency to prevent formation of water film on the surface and thus to suppress the leakage current and consequently flashover. However, the electrical property and the hydrophobicity of RTV silicone rubber coating under outdoor condition may be influenced by many environmental factors. In this studyvarious treatments, such as salt-fog, salt water immerging and UV irradiation were applied to the samples to investigate the change of the electrical property and hydrophobicity. As a result the leakage current increased and contact angle decreased asthe degradation time is longer. But the degraded RTV silicone rubber has recovered its hydrophobicity during the drying time in ambient condition because LMW(Low Molecular Weight) silicone fluid diffused from the bulk to the surface.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.168-169
• /
• 2021

A hydrophobic surface increases the contact angle between water and cement paste. There are two methods to increase water contact angle, i.e. lowering the surface energy and adjusting the surface roughness of concrete. The hydrophobicity of concrete can be quantitatively evaluated according to the chemical and physical properties of the solid surface. So far, researches have shown the chemical properties of hydrophobic concrete, however it has not covered how to control surface. This study demonstrated the hydrophobic cement paste prepared by low-resolution molds printed with a 3D printer that exhibit rough surface. Thus, we presented the most hydrophobic characteristics of mold.