• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.1
• /
• pp.3642-3654
• /
• 1975

The purpose of this thesis is to derive a unit hydrograph which may be applied to the ungaged watershed area from the relations between directly measurable unitgraph properties such as peak discharge(qp), time to peak discharge (Tp), and lag time (Lg) and watershed characteristics such as river length(L) from the given station to the upstream limits of the watershed area in km, river length from station to centroid of gravity of the watershed area in km (Lca), and main stream slope in meter per km (S). Other procedure based on routing a time-area diagram through catchment storage named Instantaneous Unit Hydrograph(IUH). Dimensionless unitgraph also analysed in brief. The basic data (1969 to 1973) used in these studies are 9 recording level gages and rating curves, 41 rain gages and pluviographs, and 40 observed unitgraphs through the 9 sub watersheds in Nak Oong River basin. The results summarized in these studies are as follows; 1. Time in hour from start of rise to peak rate (Tp) generally occured at the position of 0.3Tb (time base of hydrograph) with some indication of higher values for larger watershed. The base flow is comparelatively higher than the other small watershed area. 2. Te losses from rainfall were divided into initial loss and continuing loss. Initial loss may be defined as that portion of storm rainfall which is intercepted by vegetation, held in deppression storage or infiltrated at a high rate early in the storm and continuing loss is defined as the loss which continues at a constant rate throughout the duration of the storm after the initial loss has been satisfied. Tis continuing loss approximates the nearly constant rate of infiltration (${\Phi}$-index method). The loss rate from this analysis was estimated 50 Per cent to the rainfall excess approximately during the surface runoff occured. 3. Stream slope seems approximate, as is usual, to consider the mainstreamonly, not giving any specific consideration to tributary. It is desirable to develop a single measure of slope that is representative of the who1e stream. The mean slope of channel increment in 1 meter per 200 meters and 1 meter per 1400 meters were defined at Gazang and Jindong respectively. It is considered that the slopes are low slightly in the light of other river studies. Flood concentration rate might slightly be low in the Nak Dong river basin. 4. It found that the watershed lag (Lg, hrs) could be expressed by Lg=0.253 (L.Lca)0.4171 The product L.Lca is a measure of the size and shape of the watershed. For the logarithms, the correlation coefficient for Lg was 0.97 which defined that Lg is closely related with the watershed characteristics, L and Lca. 5. Expression for basin might be expected to take form containing theslope as {{{{ { L}_{g }=0.545 {( { L. { L}_{ca } } over { SQRT {s} } ) }^{0.346 } }}}} For the logarithms, the correlation coefficient for Lg was 0.97 which defined that Lg is closely related with the basin characteristics too. It should be needed to take care of analysis which relating to the mean slopes 6. Peak discharge per unit area of unitgraph for standard duration tr, ㎥/sec/$\textrm{km}^2$, was given by qp=10-0.52-0.0184Lg with a indication of lower values for watershed contrary to the higher lag time. For the logarithms, the correlation coefficient qp was 0.998 which defined high sign ificance. The peak discharge of the unitgraph for an area could therefore be expected to take the from Qp=qp. A(㎥/sec). 7. Using the unitgraph parameter Lg, the base length of the unitgraph, in days, was adopted as {{{{ {T}_{b } =0.73+2.073( { { L}_{g } } over {24 } )}}}} with high significant correlation coefficient, 0.92. The constant of the above equation are fixed by the procedure used to separate base flow from direct runoff. 8. The width W75 of the unitgraph at discharge equal to 75 per cent of the peak discharge, in hours and the width W50 at discharge equal to 50 Per cent of the peak discharge in hours, can be estimated from {{{{ { W}_{75 }= { 1.61} over { { q}_{b } ^{1.05 } } }}}} and {{{{ { W}_{50 }= { 2.5} over { { q}_{b } ^{1.05 } } }}}} respectively. This provides supplementary guide for sketching the unitgraph. 9. Above equations define the three factors necessary to construct the unitgraph for duration tr. For the duration tR, the lag is LgR=Lg+0.2(tR-tr) and this modified lag, LgRis used in qp and Tb It the tr happens to be equal to or close to tR, further assume qpR=qp. 10. Triangular hydrograph is a dimensionless unitgraph prepared from the 40 unitgraphs. The equation is shown as {{{{ { q}_{p } = { K.A.Q} over { { T}_{p } } }}}} or {{{{ { q}_{p } = { 0.21A.Q} over { { T}_{p } } }}}} The constant 0.21 is defined to Nak Dong River basin. 11. The base length of the time-area diagram for the IUH routing is {{{{C=0.9 {( { L. { L}_{ca } } over { SQRT { s} } ) }^{1/3 } }}}}. Correlation coefficient for C was 0.983 which defined a high significance. The base length of the T-AD was set to equal the time from the midpoint of rain fall excess to the point of contraflexure. The constant K, derived in this studies is K=8.32+0.0213 {{{{ { L} over { SQRT { s} } }}}} with correlation coefficient, 0.964. 12. In the light of the results analysed in these studies, average errors in the peak discharge of the Synthetic unitgraph, Triangular unitgraph, and IUH were estimated as 2.2, 7.7 and 6.4 per cent respectively to the peak of observed average unitgraph. Each ordinate of the Synthetic unitgraph was approached closely to the observed one.

• The Journal of Korean Society for Radiation Therapy
• /
• v.32
• /
• pp.41-52
• /
• 2020

Purpose: To find out the dosimetric usefulness, setup reproducibility and efficiency of applying 3D Bolus by comparing two treatment plans in which Commercial Bolus and 3D Bolus produced by 3D Printing Technology were applied to the neck during VMAT treatment of Hypopahrynx Cancer to evaluate the clinical applicability. Materials and Methods: Based on the CT image of the RANDO phantom to which CB was applied, 3D Bolus were fabricated in the same form. 3D Bolus was printed with a polyurethane acrylate resin with a density of 1.2g/㎤ through the SLA technique using OMG SLA 660 Printer and MaterializeMagics software. Based on two CT images using CB and 3D Bolus, a treatment plan was established assuming VMAT treatment of Hypopharynx Cancer. CBCT images were obtained for each of the two established treatment plans 18 times, and the treatment efficiency was evaluated by measuring the setup time each time. Based on the obtained CBCT image, the adaptive plan was performed through Pinnacle, a computerized treatment planning system, to evaluate target, normal organ dose evaluation, and changes in bolus volume. Results: The setup time for each treatment plan was reduced by an average of 28 sec in the 3D Bolus treatment plan compared to the CB treatment plan. The Bolus Volume change during the pretreatment period was 86.1±2.70㎤ in 83.9㎤ of CB Initial Plan and 99.8±0.46㎤ in 92.2㎤ of 3D Bolus Initial Plan. The change in CTV Min Value was 167.4±19.38cGy in CB Initial Plan 191.6cGy and 149.5±18.27cGy in 3D Bolus Initial Plan 167.3cGy. The change in CTV Mean Value was 228.3±0.38cGy in CB Initial Plan 227.1cGy and 227.7±0.30cGy in 3D Bolus Initial Plan 225.9cGy. The change in PTV Min Value was 74.9±19.47cGy in CB Initial Plan 128.5cGy and 83.2±12.92cGy in 3D Bolus Initial Plan 139.9cGy. The change in PTV Mean Value was 226.2±0.83cGy in CB Initial Plan 225.4cGy and 225.8±0.33cGy in 3D Bolus Initial Plan 224.1cGy. The maximum value for the normal organ spinal cord was the same as 135.6cGy on average each time. Conclusion: From the experimental results of this paper, it was found that the application of 3D Bolus to the irregular body surface is more dosimetrically useful than the application of Commercial Bolus, and the setup reproducibility and efficiency are excellent. If further case studies along with research on the diversity of 3D printing materials are conducted in the future, the application of 3D Bolus in the field of radiation therapy is expected to proceed more actively.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.1
• /
• pp.3-44
• /
• 1986

In order to obtain the basic physical and mechanical properties of steel wire reinforced particleboard, particleboards were formed with large particles through 2.11 mm (12 meshes) and retained on 1.27mm (20 meshes) sieves and small particles through 1.27mm (20 meshes) and retained on 0.42mm (60 meshes) sieves from the plywood mill wastes of meranti (Shorea spp.) in the form of pallmanchips, applying urea-formaldehyde resin as an adhesive on the particle surface in 10 percent on the oven dried weight of particles, and arranging steel wires of 1mm in diameter 5,10,15,20, and 25mm in longitudinal and transverse direction with crossing in the mid of the board depth in single layer boards, 10mm in longitudinal or transverse direction without crossing in two layers and 10mm in longitudinal and transverse directions with and without crossing in three steel wire layers boards. The stepwise 9-minutes-multi-pressing schedule in 5 minutes at 35 kgf/$cm^2$, 2.5 minutes at 25 kgf/$cm^2$. and 1.5 minutes at 15 kgf/$cm^2$ was applied for $300{\times}200{\times}13$mm board at the temperature of 160$^{\circ}C$ in a hot press. Specific gravity, thickness swelling, bending properties of modulus of rupture (MOR), modulus of elasticity(MOE), work to proportional limit, and work to ultimate load, internal bond (IB), and screw holding power(SHP) of the reinforced boards were analyzed on the wire openings and wire layers. The results obtained are summarized as follows; 1) In specific gravity, particleboards with large particles and small particles had higher value with more steel wire placements and more steel layers composition, 2) Particleboards with large particles in accordance with more steel wire liners composition gave very poor thickness swelling. 3) The mechanical properties of particleboards formed with large or small particles were reinforced with more steel wire layers. Therefore, bending strength was improved in modulus of rupture, modulus of elasticity, and work to ultimate load. Especiallv, particleboards with two or three steel wire layers showed the tension lamination effect when the steels in lower steel wire layer were oriented parallel to the board length. 4) The modulus of rupture, modulus of elasticity, and work to ultimate load in bending varied with opening area, distance of lengthwise wires multipled by distance of transverse wires. Particleboards formed with large particles resulted in higher value in modulus of rupture with 1.5-3 $cm^2$ opening area, 1-2cm distance between transverse wires, and 1.5-2.5cm distance between lengthwise wires. Particle boards formed with small particles showed higher value with 0.5-1.5$cm^2$ or 3.75-6.25 $cm^2$ opening area, 0.5 or 2.5cm distance between transverse wires. 5) In modulus of elasticity, particleboards formed with large particles with one steel wire layer suggested higher value with 5-3$cm^2$ opening area, 1-2.5cm distance between transverse wires and also 1-2.5 cm distance between lengthwise wires. Particleboards formed with small particles showed higher value with 0.75-1.25$cm^2$ or 3-6.25$cm^2$ opening area and 0.5 or 2.5cm distance between transverse wires. 6) Particleboards formed with large particles gaved higher value in work to ultimate load with 1-3$cm^2$ opening area. Particleboards formed with small particles showed increasing tendancy with decreasing opening area. 7) In internal bond and screw holding power, particleboards formed with large particles had increasing value in two and three steel wire layers compositions, but particleboards formed with small particles showed no difference. Particleboards formed with large particles containing one steel wire layer showed no difference in internal bond and screw holding power, and particleboards formed with small panicles containing one steel wire layer resulted in increasing value in internal bond and decreasing value in screw holding power in accordance with increase in opening area.

• Journal of Korean Society of Archives and Records Management
• /
• v.5 no.2
• /
• pp.27-48
• /
• 2005

This study investigates the current preservation and management of four records and documentary heritage in Korea that is in the UNESCO's Memory of the World Register. The study analyzes their problems and corresponding solutions in digitizing those world records heritages. This study also reviews additional four documentary books in Korea that are in the wish list to add to UNESCO's Memory of the World Register. This study is organized as the following: Chapter 2 examines the value and meanings of world records and documentary heritage in Korea. The registry requirements and procedures of UNESCO's Memory of the World Register are examined. The currently registered records of Korea include Hunmin-Chongum, the Annals of the Choson Dynasty, the Diaries of the Royal Secretariat (Seungjeongwon Ilgi), and Buljo- Jikji-Simche-Yojeol (vol. II). These records heritage's worth and significance are carefully analyzed. For example, Hunmin-Chongum("訓民正音") is consisted of unique and systematic letters. Letters were delicately explained with examples in its original manual at the time of letter's creation, which is an unparalleled case in the world documentary history. The Annals of the Choson Dynasty("朝鮮王朝實錄") are the most comprehensive historic documents that contain the longest period of time in history. Their truthfulness and reliability in describing history give credits to the annals. The Royal Secretariat Diary (called Seungjeongwon-Ilgi("承政院日記")) is the most voluminous primary resources in history, superior to the Annals of Choson Dynasty and Twenty Five Histories in China. Jikji("直指") is the oldest existing book published by movable metal print sets in the world. It evidences the beginning of metal printing in the world printing history and is worthy of being as world heritage. The review of the four registered records confirms that they are valuable world documentary heritage that transfers culture of mankind to next generations and should be preserved carefully and safely without deterioration or loss. Chapter 3 investigates the current status of preservation and management of three repositories that store the four registered records in Korea. The repositories include Kyujanggak Archives in Seoul National University, Pusan Records and Information Center of National Records and Archives Service, and Gansong Art Museum. The quality of their preservation and management are excellent in all of three institutions by the following aspects: 1) detailed security measures are close to perfection 2) archiving practices are very careful by using a special stack room in steady temperature and humidity and depositing it in stack or archival box made of paulownia tree and 3) fire prevention, lighting, and fumigation are thoroughly prepared. Chapter 4 summarizes the status quo of digitization projects of records heritage in Korea. The most important issue related to digitization and database construction on Korean records heritage is likely to set up the standardization of digitization processes and facilities. It is urgently necessary to develop comprehensive standard systems for digitization. Two institutions are closely interested in these tasks: 1) the National Records and Archives Service experienced in developing government records management systems; and 2) the Cultural Heritage Administration interested in digitization of Korean old documents. In collaboration of these two institutions, a new standard system will be designed for digitizing records heritage on Korean Studies. Chapter 5 deals with additional Korean records heritage in the wish list for UNESCO's Memory of the World Register, including: 1) Wooden Printing Blocks(經板) of Koryo-Taejangkyong(高麗大藏經) in Haein Temple(海印寺); 2) Dongui-Bogam("東醫寶鑑") 3) Samguk-Yusa("三國遺事") and 4) Mugujeonggwangdaedaranigyeong. Their world value and importance are examined as followings. Wooden Printing Blocks of Koryo-Taejangkyong in Haein Temple is the worldly oldest wooden printing block of cannon of Buddhism that still exist and was created over 750 years ago. It needs a special conservation treatment to disinfect germs residing in surface and inside of wooden plates. Otherwise, it may be damaged seriously. For its effective conservation and preservation, we hope that UNESCO and Government will schedule special care and budget and join the list of Memory of the Word Register. Dongui-Bogam is the most comprehensive and well-written medical book in the Korean history, summarizing all medical books in Korea and China from the Ancient Times through the early 17th century and concentrating on Korean herb medicine and prescriptions. It is proved as the best clinical guidebook in the 17th century for doctors and practitioners to easily use. The book was also published in China and Japan in the 18th century and greatly influenced the development of practical clinic and medical research in Asia at that time. This is why Dongui Bogam is in the wish list to register to the Memory of the World. Samguk-Yusa is evaluated as one of the most comprehensive history books and treasure sources in Korea, which illustrates foundations of Korean people and covers histories and cultures of ancient Korean peninsula and nearby countries. The book contains the oldest fixed form verse, called Hyang-Ka(鄕歌), and became the origin of Korean literature. In particular, the section of Gi-ee(紀異篇) describes the historical processes of dynasty transition from the first dynasty Gochosun(古朝鮮) to Goguryeo(高句麗) and illustrates the identity of Korean people from its historical origin. This book is worthy of adding to the Memory of the World Register. Mugujeonggwangdaedaranigyeong is the oldest book printed by wooden type plates, and it is estimated to print in between 706 and 751. It contains several reasons and evidence to be worthy of adding to the list of the Memory of the World. It is the greatest documentary heritage that represents the first wooden printing book that still exists in the world as well as illustrates the history of wooden printing in Korea.