• KSBB Journal
• /
• v.19 no.6 s.89
• /
• pp.421-426
• /
• 2004

The extraction and separation of isoflavones from Korean soybean were peformed by various mechanical and chemical extraction methods. They included solvent extraction, stirring, supersonification and sub/supercritical water extraction. From the experimental results of the variation of solvent extraction by change in composition, the increase in extraction of a specific compound by stirring or supersonic energy, and the application of supercritical fluid with superior solvating power over solvents, the sonification was the most desirable extraction method in extracting aglycone isoflavones, daidzein and genistein from Korean soybean.

• Current Photovoltaic Research
• /
• v.7 no.1
• /
• pp.21-27
• /
• 2019

Lifetime of Si photovoltaics modules are about 25 years and a large amount of waste modules are expected to be discharged in the near future. Therefore, the extraction and collection of valuable metals out of discharged Si modules will be one of the important technologies. In this study, we demonstrated that supercritical $CO_2$ extraction method can be effectively used to remove Cu, one of the abundant elements in the module, as well as its oxide form, $Cu_2O$. Especially, we proved that the addition of hexane as co-solvent is effective for the removal of both materials. The optimal ratio of $CO_2$ and hexane was 4:1 at a fixed temperature and pressure of $250^{\circ}C$ and 250 bar, respectively. In addition, it was proven that the removal of $Cu_2O$ was preceded via reduction of $Cu_2O$ to Cu.

• Nuclear Engineering and Technology
• /
• v.40 no.2
• /
• pp.155-162
• /
• 2008

Heat transfer experiments in an annulus passage were performed using SPHINX(Supercritical Pressure Heat Transfer Investigation for NeXt Generation), which was constructed at KAERI(Korea Atomic Energy Research Institute), to investigate the heat transfer behaviors of supercritical $CO_{2}$. $CO_{2}$ was selected as the working fluid to utilize its low critical pressure and temperature when compared with water. The mass flux was in the range of 400 to 1200 $kg/m^{2}s$ and the heat flux was chosen at rates up to 150 $kW/m^{2}$. The selected pressures were 7.75 and 8.12 MPa. At lower mass fluxes, heat transfer deterioration occurs if the heat flux increases beyond a certain value. Comparison with the tube test results showed that the degree of heat transfer deterioration in the heat flux was smaller than that in the tube. In addition, the Nusselt number correlation for a normal heat transfer mode is presented.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.33 no.4
• /
• pp.32-43
• /
• 2020

Objectives : The aim of this study was to investigate the anti-oxidant and anti-aging effect of the seed of Camellia japonica L. extracted by supercritical CO₂. Methods : The cell viability was performed by MTT assay. Nitric oxide (NO) production was performed by NO assay. The anti-oxidant effect was performed by beta-carotene bleaching assay and the intracellular proteome was analyzed expression of each 15 proteins by 2-D electrophoresis. Results : Fatty acid analysis of extract from Camellia japonica L. has shown oleic acid was 84%. And the antioxidant effect was about 186% compared with alpha-tocoperol(0.1%) by beta carotene bleaching assay. In 2D PAGE analysis, fifteen protein changes in five mechanisms which was collagen synthesis pathway, MMPs, ECM-cell interaction, cytokine, antioxidant enzymes were analyzed. Conclusions : On this study extract from seed of Camellia japonica L. by supercritical extraction could be used as a antioxidant and antiaging substance for the skin.

• Journal of Convergence for Information Technology
• /
• v.11 no.12
• /
• pp.236-243
• /
• 2021

The aim of this study was to evaluate the anti-oxidant and anti-wrinkle effect of the black carrot(BC) extracted by supercritical dioxide(SC-CO₂). DPPH/ABTS radical scavenging and total polyphenol contents were measured to investigate the anti-oxidant activity of the BC supercritical extract. Collagen production and MMP-1 expression were assessed in normal human dermal fibroblasts(NHDF) for anti-wrinkle activity, The black carrot extract showed the highest total phenolic content(9.037±1.123 mg GAE/g extract) and the best antioxidant properties as shown by DPPH and ABTS assay. The supercritical fluid extracts of black carrot exhibited low toxicity to NHDF cells. In addition, the supercritical fluid extracts showed MMP-1 inhibition and type I pro-collagen synthesis inducing activities in a dose-dependent manner, respectively. Therefore, these results suggest that the black carrot is a potential source of high anti-oxidative, solvent-free and anti-aging material with promising applications in cosmetic, food, and beauty-food industries.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.4
• /
• pp.41-50
• /
• 2000

Cement-bonded particleboard is being used as outdoor siding material all over the world, because this composite particularly bears a light weight, high resistance against fire, decay, and crack by cyclic freezing and thawing, anti-shock property, and strength enhancement. Construction systems are currently changing into a frame-building style and wooden houses are being constructed with prefabrication type. Therefore, they require a more durability at outdoor-exposed sides. In this study, the cement hydration property for Korean pine particle, Japanese larch particle and face- and middle layer particles (designated as PB particle below) used in Korean particleboard-manufacturing company was investigated, and the rapid manufacturing characteristics of cement-bonded particleboard by supercritical $CO_2$ curing was evaluated. Korean pine flour showed a good hydration property, however, larch flour showed a bad one. PB particle had a better hydration property than larch flour. The addition of $Na_2SiO_3$ indicated a negative effect on hydration, however, $MgCl_2$ had a positive one. Curing by supercritical $CO_2$ fluid gave a conspicuous enhancement in the performances of cement-bonded particleboards compared to conventional curing. $MgCl_2$ 3%-added PB particle had the highest properties, and $MgCl_2$ 1%-added Korean pine particle had the second class with the conditions of cement/wood ratio of 2.7, a small fraction-screened particle and supercritical curing. On the contrary, the composition of non-hammermilled or large fraction-screened particle at cement/wood ratio of 2.2 was poorer. Also, the feasibility for actual use of 3%-added, small PB particle-screened fraction was greatest of all the conventional curing treatments. Relative superiority of supercritical curing vs. conventional curing at dimensional stability was not so apparent as in strength properties. Through the thermogravimetric analysis, it was ascertained that the peak of a component $CaCO_3$ was highest, and the two weak peaks of calcium silicate hydrate and ettringite and $Ca(OH)_2$ were present in supercritical treatment. Accordingly, it was inferred that the increased formation of carbonates in board contributes to strength enhancement.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.2
• /
• pp.254-263
• /
• 2015

In this study, numerical simulations are carried out to investigate the dynamic SGS model effects in a Kerosene-LOx coaxial swirl injector under high pressure conditions. The turbulent model is based on large-eddy simulation (LES) with real-fluid transport and thermodynamics. To assess the effect of the dynamic subgrid-scale (SGS) model, the dynamic SGS model is compared with that of the algebraic SGS model. In a swirl injector under supercritical pressure, the characteristics of temporal pressure fluctuation and power spectral density (PSD) present comparable discrepancies dependant on the SGS models, which affect the mixing characteristics. Mixing efficiency and the probability density (PDF) function are conducted for a statistical description of the turbulent flow fields according to the SGS models. The back-scattering of turbulent kinetic energy is estimated in terms of the film thickness of the swirl injector.

• Textile Coloration and Finishing
• /
• v.31 no.1
• /
• pp.14-24
• /
• 2019

In this study, dyeability of PET fabric was investigated depending on dyeing temperature, pressure, and leveling time using laboratory scale supercritical $CO_2(scCO_2)$ dyeing machine. Dyeing temperature, pressure, leveling time were varied from 100, 120, $130^{\circ}C$, 150, 200, 250bar, 40, 60, 80, 100min, respectively. It is proved that the higher temperature of $scCO_2$ dyeing process, the higher K/S value and the lower $L^*$ value, which in turn means the lower amount of dyeing molecules remained after process done. Compared 200bar with 250bar of dyeing pressure, $scCO_2$ dyeing fabrics under 250bar appeared to have a lower $L^*$ value, a higher K/S value than those from 200bar, meaning that dyeing color turns to darker with higher dyeing pressure. The experiments showed that the most ideal condition for $scCO_2$ dyeing process is $120^{\circ}C$, 250bar for 60 - 100min of leveling time.

• Textile Coloration and Finishing
• /
• v.33 no.1
• /
• pp.31-39
• /
• 2021

In this study, the dyeing properties of supercritical fluid dyed nylon fabrics were investigated which use two types of dyes for dyeing nylon. For other dyeing conditions were referred to related literature, and dyeing was performed with different dyeing concentrations. Dyeability was confirmed through measurement of washing fastness and color coordinate, and a calibration curve of each dye was drawn up and the absorbance of the residual dye was measured to confirm the amount of residual dye and the dye exhaustion rate at the corresponding concentration. As a result of color difference measurement, the color intensity increased as the concentration increased, but the increase was insignificant at high concentration. This tendency was more obvious in C.I. Disperse Orange 155 than in C.I. Disperse Yellow 42. The dye absorption rate also decreases as the concentration increases, but at 0.85% o.w.f concentration, C.I. Disperse Yellow 42 was 97.29% and C.I. Disperse Orange 155 was 93.77%. For both dyes, the wash fastness dropped by 0.5 to 1 class from the sample that was dyed at a concentration of 0.5% o.w.f in the wash fastness test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.5
• /
• pp.333-338
• /
• 2022

The single jet of decane/methylcyclohexane mixed fuel that is surrogate for kerosene was injected into supercritical environment and visualized using shadowgraph technique. The injection pressure drop of the fuel jet of T_r = 0.484 was kept constant at 0.5 MPa and the experiment was conducted above the critical point of the mixed fuel, and the reduced temperatures of the chamber was changed from 1.00 to 1.23, and the reduced pressures was 1.00 and 1.38. As an index for reducing the density of jets sprayed into the supercritical environment, the brightness intensity of the post-processed jet image was observed with the internal temperature and pressure of the chamber. It was confirmed that the decrease in the brightness intensity of the jet when the temperature inside the chamber increased, and when the pressure inside the chamber was higher at the same temperature, the decrease in the brightness intensity of the jet was delayed. When the pressure inside the chamber is high, it is thought that the change in brightness intensity is delayed due to the increase in the pseudo-critical temperature of the fuel and the increase in the temperature required to reduce the density of the fuel jet.