• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.11
• /
• pp.848-853
• /
• 2010

We have grown GaN nanowires by the low pressure MOCVD method on Ni deposited oxidized Si surface and have established optimum conditions by observing surface microstructure and its photoluminescence. Optimum growth temperature of $880^{\circ}C$, growth time of 30 min, TMG source flow rate of 10 sccm have resulted in dense nanowires on the surface, however further increase of growth time or TMG flow rate has not increased the length of nanowire but has formed nanocrystals. On the contrary, the increase of ammonia flow has increased the length of nanowires and the coverage of nanowire over the surface. The shape of nanowire is needle-like with a Ni droplet at its tip; the length is tens of micron with more than 40 nm in diameter. Low temperature photoluminescence obtained from the sample at optimum growth condition has revealed several peaks related to exciton decay near band-edge, but does not show any characteristic originated from one dimensional quantum confinement. Strong and broad luminescence at 2.2 eV is observed from dense nanowire samples and this suggests that the broad band is related to e-h recombination at the surface state in a nanowire. The current result is implemented to the nanowire device fabrication by nanowire bridging between micro-patterned neighboring Ni catalysis islands.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.2
• /
• pp.51-55
• /
• 2011

We investigated the etching characteristics of zinc oxide (ZnO) thin films deposited by the atomic layer deposition method. The gases of the inductively coupled plasma chemistry consisted of $Cl_2$, Ar, and $O_2$. The maximum etch rate was 40.3 nm/min at a gas flow ratio of $Cl_2$/Ar=15:5 sccm, radio-frequency power of 600 W, bias power of 200 W, and process pressure of 2 Pa. We also investigated the plasma induced damage in the etched ZnO thin films using X-ray diffraction (XRD), atomic force microscopy and photoluminescence (PL). A highly oriented (100) peak was present in the XRD spectroscopy of the ZnO samples. The full width at half maximum value of the ZnO sample etched using the $O_2/Cl_2$/Ar chemistry was higher than that of the as-deposited sample. The roughness of the ZnO thin films increased from 1.91 nm to 2.45 nm after etching in the $O_2/Cl_2$/Ar plasma chemistry. Also, we obtained a strong band edge emission at 380 nm. The intensities of the peaks in the PL spectra from the samples etched in all of the chemistries were increased. However, there was no deep level emission.

• Korean Journal of Human Ecology
• /
• v.6 no.1
• /
• pp.97-109
• /
• 1997

Sean means a narrow cloth added to the edge of costume or cushion. At the beginning, Seon was originated to prevent from fraying warp of cloth or wearing out of cloth. However, with the progress of clothing culture, it is used to satisfy the human desire of decoration and enhance the function of costume. The Seon appeared on costumes of Ming dynasty was simple compared to that of the period preceeding it. The position of Seon was mostly at neckline, end of sleeves and hemline. The width of Seon also was quite monotonous and lacks of varieties. The patterns of Seon were limited to ax, cloud and dragon and cloud and chinese phoenix. And the colors used were also limited to four colors, namely Blue, Red Crimson and Black. In Ming dynasty, the same colors of Seon as those of the costume were more preferably used, while different colors of Seon were used in the previous era. The reason why Seon in Ming dynasty show simple design and use the same colors as those of the costume was due to Ming dynasty's desire to represent and to enhance her castic political structure. The need for class distinction was expressed through the pattern rather than the colors of the costumes themselves. While, in Ming dynasty, Bo(補) which was attached to the breast and the shoulders was used to represent the social class because it could be easily distinguished. In Ming dynasty, to stress Bo and to make Seon less conspicuous, Seon became simple and the colors of Seon were same as those of the costumes avoiding strong contrast in style and colors.

• Atmosphere
• /
• v.27 no.3
• /
• pp.277-290
• /
• 2017

Characteristics of precipitation in South Korea during the 2016 Changma period (6/18~7/30) are analyzed in great details. El $Ni{\tilde{n}}o$-induced tropical Indian Ocean (IO) basin-wide warming lasts from spring to early summer and induces the western North Pacific subtropical high (WNPSH) circulation anomaly through an equatorial Kelvin wave during the 2016 Changma period. Along the northern edge of the WNPSH, strong precipitation occurred, in particular, over eastern China and southern Japan. During the Changma period, South Korea had the near-normal mean precipitation amount (~332 mm). However, about 226 mm of rain fell in South Korea during 1 July to 6 July, which amounts to 67% of total Changma precipitation in that year. Upper-level synoptic migratory lows and low-level moisture transport played an essential role, especially from 1 July to 3 July, in triggering an abrupt development of fronts over the Korean Peninsula and the eastern continent China. The front over the eastern China migrates progressively eastward, which results in heavy rainfall over the Korean peninsula from 1 to 3 July. In contrast, from 4 to 6 July, the typhoon (NEPARTAK) affected an abrupt northward advance of the North Pacific subtropical high (NPSH). The northward extension of the NPSH strengthens the Changma front and induces the southerly flows toward the Korean peninsula, giving rise to an increase in heavy rainfall. The NEPARTAK is generated due to interaction of the Madden-Julian Oscillation (MJO), equatorial Rossby wave and Kelvin waves.

• Atmosphere
• /
• v.27 no.4
• /
• pp.455-466
• /
• 2017

In Korea, property and human damages occur annually due to heavy precipitation during the summer. On August 8, 2015, heavy rainfall occurred in the Seoul metropolitan area due to an outflow boundary, and $77mmhr^{-1}$ rainfall was recorded in Gwangju, Gyeonggi Province. In this study, the simulation of the WRF numerical model is performed to understand the cause and characteristics of heavy rainfall using the Conditional Instability of the Second Kind (CISK), potential vorticity (PV), frontogenesis function, and convective available potential energy (CAPE) analyses, etc. Convective cells initiated over the Shandong Peninsula and located on the downwind side of an upper level trough. Large amounts of water vapor were supplied to the Shandong Peninsula along the southwestern edge of a high pressure system, and from the remnants of typhoon Soudelor. The mesoscale convective system (MCS) developed through CISK process and moved over to the Yellow Sea. The outflow boundary from the MCS progressed east and pushed cold pool eastward. The warm and humid air over the Korean Peninsula further enhanced convective development. As a result, a new MCS developed rapidly over land. Because of the latent heat release due to convection and precipitation, strong potential vorticity was generated in the lower atmosphere. The rapid development of MCS and the heavy rainfall occurred in an area where the CAPE value was greater than $1300Jkg^{-1}$ and the fronto-genesis function value of 1.5 or greater coincided. The analysis result shows that the MCS driven by an outflow boundary can be identified using CISK process.

• Korean Journal of Remote Sensing
• /
• v.33 no.4
• /
• pp.359-375
• /
• 2017

We developed fog detection algorithm (KNU_FDA) based on the optical and textural properties of fog using satellite (COMS) and ground observation data. The optical properties are dual channel difference (DCD: BT3.7 - BT11) and albedo, and the textural properties are normalized local standard deviation of IR1 and visible channels. Temperature difference between air temperature and BT11 is applied to discriminate the fog from other clouds. Fog detection is performed according to the solar zenith angle of pixel because of the different availability of satellite data: day, night and dawn/dusk. Post-processing is also performed to increase the probability of detection (POD), in particular, at the edge of main fog area. The fog probability is calculated by the weighted sum of threshold tests. The initial threshold and weighting values are optimized using sensitivity tests for the varying threshold values using receiver operating characteristic analysis. The validation results with ground visibility data for the validation cases showed that the performance of KNU_FDA show relatively consistent detection skills but it clearly depends on the fog types and time of day. The average POD and FAR (False Alarm Ratio) for the training and validation cases are ranged from 0.76 to 0.90 and from 0.41 to 0.63, respectively. In general, the performance is relatively good for the fog without high cloud and strong fog but that is significantly decreased for the weak fog. In order to improve the detection skills and stability, optimization of threshold and weighting values are needed through the various training cases.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.3 s.46
• /
• pp.251-258
• /
• 2000

Based on the numerical investigations using steel bridge pier subjected to strong seismic excitations a new approach to seismic damage assessment for steel structures and their members has been proposed in conjunction with the suggested definition of failure state. The relevant failure form of the steel pier is evaluated. It is revealed that when a seismic load has a short period, the failure of global buckling beyond the allowable displacement is more dominant than that by that of the local buckling caused by the accumulation of plastic strain. When a seismic load is not beyond this certain part, but repeats within the range of where a plastic deformation occurs, the plastic strain is accumulated on the partial element of bottom edge of steel pier and the failure occurs by the local buckling from the accumulated plastic local strain.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.5
• /
• pp.1-11
• /
• 2006

The effects of continuous blowing on flow control and stall suppression for flows over a NACA 0015 airfoil at low Reynolds numbers were numerically investigated through its parameter variation on unstructured meshes. The aerodynamic force and moment variations due to flow control were examined, along with the stall angle-of-attack change for stall suppression. The results showed that blowing with relatively strong jet increases lift at the cost of drag increment below stall angle. Continuous blowing delays flow stall when it is implemented near the leading edge. When the blowing jet was aligned along the flow direction on the airfoil, the favorable flow control effect was most significant below the stall angle of attack.

• The Journal of the Korea Contents Association
• /
• v.10 no.10
• /
• pp.318-325
• /
• 2010

This study is to examine loyalty building model which reflected differentiated traits of professional service to establish strong loyalty for gaining competitive edge. Professional service is where consumer can not easily predict the result of service as well as other common traits. It also has trait that is difficult to evaluate service satisfaction and quality even after using the service because knowledge imbalance between service provider and user is great. Therefore, in professional service, satisfaction and emotion that consumer perceives in the service use process will play critical role in loyalty formation. As a result, the model of this study divided dimension into responsiveness satisfaction which is satisfaction dimension of professional service use process, interaction satisfaction, technical satisfaction and structurally examined the relationship between emotional commitment and cognitive commitment and the relationship between dimension of commitment and loyalty. The analysis result show that dimension of satisfaction which perceived in professional service use process increases both emotional commitment and cognitive commitment and these commitments effect to loyalty formation.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.41 no.6
• /
• pp.285-294
• /
• 2004

Median Filters in the Signal Processing have been most widely used and have demonstrated the most strongest effects. This paper proposes the Adaptive Median Filters by using noise detection. The basic algorithm of the proposed filters is to determine whether noise or not by the each noise judgement standards, and then take the Median Filter if it satisfies the conditions as a result of judgement and returns to the original image(No Filters) if not. This paper presented Noise Detection by Local Variance and Local Central Variance for noise judgement, compared and analyzed the features and performance of existing [5]∼[10] Filters. Filter improved on the result of executing the existing filters at the same condition and showed the effects over that when it was judged with naked eyes. Accordingly, the Adaptive Median Filters by Local Variance and Local Central Variance was proven to have reinforced edge preservation ability and have the strong features for removing the Impulse Noise of the Median Filter.