• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.3
• /
• pp.353-358
• /
• 2010

This research introduces a new and improved design for a pneumatic cylinder driven roll feeder wherein each of the principal rotating feeder parts is configured so as to have feeding accuracy and to be low manufacturing cost. The feed pitch accuracy of the proposed roll feeder was evaluated by measuring lengths of cut offs of the strip stock with a shear attached to an air press. The air press was designed, manufactured, and mounted on the same table of the proposed roll feeder such that the strip stock maintained horizontal plane until the strip stock entered into the shear. The proposed roll feeder and the air press were designed to be operated automatically by a PLC employed controller. The feed pitch accuracy of the proposed roll feeder was analyzed by setting the pitch as 10, 12.5, and 15mm. At each predetermined feed pitch, the proposed roll feeder was tested 300 times as one test set and replicated three times. The average lengths of the cut offs of the strip stock ranged from 9.98 to 10.13mm, from 12.42 to 12.57mm, and from 14.96 to 15.06mm at the predetermined 10, 12.5, and 15mm feed pitch, respectively, among the total of 900 samples of each feed pitch. Main cause of variation of the length of the cut off of the strip stock fed by the proposed roll feeder was considered to be fluctuation of the air press during recompressing period of the air compressor to pressurize the air in the air tank. The largest difference between the maximum and the minimum length of the cut off was appeared while the air compressor recompressing the air. The air compressor used for this study restricted the air delivered to the proposed roll feeder while it was still running. Thus, this air delivery restriction problem should be improved by stabilizing the air press while the proposed roll feeder is running.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.221-224
• /
• 2005

In this paper, We have designed, fabricated and measured a stacked planar antenna for Ultra-Wideband communication. Radiation parts of the antenna have exponential curve and fed by strip feeding network. We have used the HFSS of Ansoft to simulate the antenna. It was designed to work on a substrate Teflon of thickness 1.575mm and relative permittivity 3.2. The proposed antenna covered the entire UWB band( 3.1GHz $\sim$ 10.6GHz ) for S11$\leq$l0dB. Also the proposed antenna show a good characteristics, linear phase, omni -directional pattern lot UWB applications. Besides the measured results have a reasonable agreement with the simulated results.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.3
• /
• pp.14-25
• /
• 1990

A model predicting thermal and wear crown in order to control strip crown and shape has been investigated at the hot roll mill. A basic equation of predicting wear crown was obtained experimentally whereas thermal crown was approximately analyzed by the integral method. The calculated result based on the accumulative model of basic eauation coincides with that measured under the real rolling conditions. The effect of wear corwn is also analyzed by the longitudinal feeding method of the work roll. The high frequency feeding method is recommended in removing local wear effectively.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.80-85
• /
• 2002

The progressive die for U-bending production part is a very specific division. This study reveals the Sheet metal forming process with multi-forming die by Center Carrier type feeding system. Through the FEM simulation by DEFORM it was accepted to u-bending process as the first performance to design in strip process layout design. The next process of die development was studied according to sequence of die development.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.5
• /
• pp.475-483
• /
• 2013

In this paper, a coupled-fed monopole antenna for LTE/WWAN mobile handset applications is presented. The antenna consists of a monopole, a coupling strip, a feeding pad, a stub, and a shorting strip. The basic resonance of the monopole combines with the resonance formed by the coupling that occurs between the coupling strip and the feeding pad to include LTE700(698~787 MHz), GSM850(824~894 MHz), and GSM900(890~960 MHz) bands. The resonance of the stub combines with the harmonics of the monopole to include GSM1800(1,710~1,880 MHz), GSM1900(1,850~1,990 MHz), and UMTS(1,920~2,170 MHz) bands. Therefore, the proposed antenna is suitable as antenna for hexa-band mobile handset applications, covering LTE700, GSM850, GSM900, GSM1800, GSM1900, and UMTS bands. A stable and omni-directional radiation pattern with reasonable gains is observed within the operating bandwidth.

• Asian-Australasian Journal of Animal Sciences
• /
• v.10 no.6
• /
• pp.599-602
• /
• 1997

Fluctuation of fungal zoospores on agar strips were observed in the rumen of sheep fed three different levels of dietary concentrate, timothy hay: concentrate = 3:0 (AF diet), timothy hay: concentrate = 2:1 (MC diet), timothy hay : concentrate = 1:2 (HC diet) respectively. The number of zoospores on the strip was drastically decreased after morning feed with AF diet. The number was the highest at 0 h ($1.34{\times}10^2/cm^2$), then declined to $2.0{\times}10^3/cm^2$ at 9 h after feeding. In the rumen of animals fed MC diet, the number of zoospores decreased with time after feeding, although the decrement was slower than that with AF diet. During 0-3 h after feeding, number of zoospores was $1.6{\times}10^4/cm^2$. Although the number slightly decreased at 6 and 9 h, relatively high levels were maintained. It seems that the inducers for zoospore-release were maintained at relatively high concentration throughout incubation period. The fluctuation pattern of number of germinated zoospores was different in the rumen of animals fed HC diet from those of AF and MC diets. The number of zoospores was constantly maintained at lower level ($1.0{\times}10^3/cm^2$) than the other diets. For MC diet, continuous high number of germinated zoospores may be due to the continuous release of zoospores by hemes in timothy hay and concentrate feed, and by unknown mechanisms. Unlike AF diet which promoted relatively rapid decline of zoosporogenesis, supplementation of concentrate feed to the timothy hay did not promote such rapid decline of zoosporogenesis. It was suggested that release of inducers for zoosporogenesis from concentrate feed persisted longer time than from timothy hay. HC diet promoted the lowest zoospore production, suggested the lowest fungal population size in this experiment. These results show that an appropriate amount of concentrate may support fungal growth and stimulate zoosporogenesis in the rumen.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.6
• /
• pp.152-157
• /
• 2012

This study investigates compressive strength of ice pellet strip which is potential medium for Natural Gas Hydrate(NGH) extruded from die holes of Twin-roll Press for Continuous Pelletizing(TPCP). Recently, the prototype of TPCP is newly developed where ice powder is continuously fed and extruded into strip-type pellet between twin rolls. The system is specifically designed for future expansion towards mass-production of ice pellet strips or solid form of natural gas hydrate. It is shown that the compressive strength of pellet strip heavily depends on factors in extrusion process such as disk size, surface smoothness, ring size, taper shape, feeding mechanism, and rotational speed. Here, the mechanism of TPCP, along with compressive strength of pellets is discussed in terms of its feasibility for producing NGH pellets in the future.

• Food Science of Animal Resources
• /
• v.32 no.4
• /
• pp.414-427
• /
• 2012

Carcass characteristics and meat quality traits as a function of endpoint months of slaughter age (26 vs 32 mon) and chiller ageing (1 vs 10 d) were evaluated for m. longissmus of 26 Hanwoo steers fed with commercial diets including whole crop barley silage. Totally twenty six Hanwoo steers for 6 mon of age that were fed until 26 mon of age constituted the short term-fed group and fed until 32 mon of age constituted long-term fed group. Carcasses were chilled for 24 h and were graded. Strip loin samples were divided into two age groups (1 d and 10 d). Long-term feeding increased carcass weight, rib-eye area, yield grade, marbling score, firmness and quality grade of the meat. The feeding for 32 mon produced tender, juicy meat (p<0.01) with lower cooking loss and higher rating score (p<0.05) than short term feeding, while other quality traits were not influenced by the length of feeding. Intramuscular fat content and oxidative stability (TBARS value) were significantly (p<0.05) higher in beef from long-term feeding however the length of feeding did not alter the fatty acid composition. Chiller aging reduced instrumental tenderness (WBSF value), improved color, sensory tenderness, acceptability and rating of beef. The results of the present study mirrors that Hanwoo steers until 32 mon of age overall improved carcass traits and palatability compared to that for 26 mon. However, from the viewpoints of economical and environmental aspects, cost of the additional feeding for 6 mon for value-adding of eating quality was relatively high and the effects in turn were limited.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.2
• /
• pp.45-51
• /
• 2003

The multi-piloting type progressive die for U-bending sheet metal production part is a very specific division. This study reveals the sheet metal forming process with multi-forming die by center carrier type feeding system. Through the FEM simulation by DEFORM, it was accepted to u-bending process as the first performance to design of strip process layout. The next process of die development was studied according to sequence of die development, i.e die structure, machining condition for die making, die materials, heat treatment of partially die components, know-how and so on. The feature of this study is the die development of scrapless progressive die of multi-stage through the modeling on the I-DEAS program, components drawing on the Auto-LISP, CAD/CAM application, ordinary machine tool operating and revision by tryout.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.05a
• /
• pp.295-300
• /
• 2001

The progressive die performs a series of fundamental sheet metal working, particularly this study regards to develop the center carrier feeding type die for thick sheet metal(SS41, 2.5mm) production that is a specific division. In order to prevent defect on the production, the analysis of production part, optimum design of strip process layout, die design and die making and tryout etc. are necessary. In this study, we designed and predicted a progressive die of multi stages by wide collected data base and computer aided method.